Re: [PATCH v1] ARM: dts: nitrogen6x: add USB host 1 support

[Troy Kisky]

On 2/22/2016 1:03 PM, Peter Seiderer wrote:
> Regulator stuff and pin configuration copied from imx6qdl-nitrogen6_max.dtsi
> and checked against Boundary Devices linux kernel tree ([1]).
> 
> [1] https://github.com/boundarydevices/linux-imx6/blob/boundary-imx_3.14.28_1.0.0_ga/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
> 
> Signed-off-by: Peter Seiderer <ps.report@xxxxxxx>
> ---
>  arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi | 25 ++++++++++++++++++++++---
>  1 file changed, 22 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
> index c6c590d..81f8c5c 100644
> --- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
> @@ -85,9 +85,21 @@
>  			enable-active-high;
>  		};
>  
> -		reg_can_xcvr: regulator@3 {
> +		reg_usb_h1_vbus: regulator@3 {
>  			compatible = "regulator-fixed";
>  			reg = <3>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_usbh1>;
> +			regulator-name = "usb_h1_vbus";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_can_xcvr: regulator@4 {
> +			compatible = "regulator-fixed";
> +			reg = <4>;
>  			regulator-name = "CAN XCVR";
>  			regulator-min-microvolt = <3300000>;
>  			regulator-max-microvolt = <3300000>;
> @@ -96,9 +108,9 @@
>  			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
>  		};
>  
> -		reg_wlan_vmmc: regulator@4 {
> +		reg_wlan_vmmc: regulator@5 {
>  			compatible = "regulator-fixed";
> -			reg = <4>;
> +			reg = <5>;
>  			pinctrl-names = "default";
>  			pinctrl-0 = <&pinctrl_wlan_vmmc>;
>  			regulator-name = "reg_wlan_vmmc";
> @@ -515,6 +527,12 @@
>  			>;
>  		};
>  
> +		pinctrl_usbh1: usbh1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_17__GPIO7_IO12          0x0b0b0




I'm ok with this patch, but a more correct fix would be to add a
reset-gpios to usbh1 instead, as this is a reset pin for
a usb hub. So if nobody else has a problem,

Acked-by: Troy Kisky <troy.kisky@xxxxxxxxxxxxxxxxxxx>


> +			>;
> +		};
> +
>  		pinctrl_usbotg: usbotggrp {
>  			fsl,pins = <
>  				MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
> @@ -632,6 +650,7 @@
>  };
>  
>  &usbh1 {
> +	vbus-supply = <&reg_usb_h1_vbus>;
>  	status = "okay";
>  };
>  
>