Re: [PATCH 1/3] ARM: dts: omap5-board-common: enable rtc and charging of backup battery

[Tony Lindgren]

* Grygorii Strashko <grygorii.strashko@xxxxxx> [160113 07:15]:
> On 01/13/2016 04:55 PM, Nishanth Menon wrote:
> > On 01/13/2016 04:25 AM, H. Nikolaus Schaller wrote:
> >>
> >> I wonder now what MODE1 is.
> >>
> >> In my OMAP5 TRM (Version "Y" - may be too old) the MODE1 is tagged as "reserved".
> >>
> >> Maybe "reserved" happens to output a "1" on OMAP5 and a "0" on the X15?

The 5430 data manual I listed in the commit states mode 1 is for
msecure. It is unlikely it got changed for 5432 as the mux registers
tend to stay the same for most part across a SoC generation with just
devices being enabled or disabled.

For beagle-x15, the msecure is now called "powerhold" and seems to
have some additional or different functionality in the PMIC. So
that's a separate issue from this one.

> >> And as far as I am aware there is no "driver" for some MSECURE module (but I don't know the details of MSECURE control by software).
> > 
> > Good catch. This one is interesting. If my memory serves me right,
> > MSECURE signal from SoC is triggered in secure mode (trustzone) - the
> > requirement was that certain PMIC modifications should only be done in
> > secure mode for certain product applications. What this means is that
> > certain functions of the PMIC will be unavailable when the SoC is
> > running in "untrusted" mode.
> > 
> > Instead, the usual mode of operation is to set it up as GPIO (as Nikolas
> > pointed below) and either use GPIO HOG or default weak pull to keep it
> > in the required state.
> > 
> > I think it is better to set it as GPIO than as DRM_MSECURE.

Well we do have the data manual saying it's the msecure pin, and
we are muxing it to msecure for omap4 in twl6030_omap4.dtsi. And a
TI commit has used msecure mode for GP omap5 evm at least here:

https://gitlab.com/ubuntu-omap/u-boot-omap5/commit/dcc5279ffe880e874abb4d7f95302a34ab4968ca

I've added Keerthy to Cc, maybe he knows how this should be handled
in the long run?

So if we start changing things to GPIO mode, we really need some
further explanations and neeed to handle the GPIO pin properly in
the TWL driver. And it should be done in a separate patch for all
of the TWL SoCs.

> > This is probably also the reason why this mode is NOT in public TRM -
> > all security related topics are probably in the NDA only secure TRM
> > addendum.

Right, probably the msecure pin has been set reserved in the public TRM
because of whatever NDA reasons there might be to not allow writes to RTC.

> > I'd suggest setting up a GPIO hog and a mux to GPIO for board-common (we
> > are not doing any HS OMAP5 at least in public domain :) ).
> 
> Yeah. As I remember the same issue was with OMAP4 (twl6030_omap4.dtsi)
> and, again if i remember correctly, someone reported that sys_drm_msecure might have different values
> on different SoCs. Also I'd like to note that on Old non-DT kernel such functionality
> was always modeled using GPIO.

Care to dig up some more information on that?

I don't have anything against adding GPIO handling to the TWL driver
so it can be optionally specified. But that's clearly a separate patch
and should be done by somebody who knows more about the issue and has
a test case needing the GPIO logic for this pin.

Regards,

Tony