Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel

From: Julian Margetson
Date: Mon Dec 21 2015 - 12:27:20 EST

Next message: Daniel Cashman: "[PATCH v7 1/4] mm: mmap: Add new /proc tunable for mmap_base ASLR."
Previous message: Andy Shevchenko: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
In reply to: Julian Margetson: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
Next in thread: Andy Shevchenko: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 12/21/2015 12:48 PM, Andy Shevchenko wrote:

On Sun, 2015-12-20 at 22:55 +0200, Andy Shevchenko wrote:

On Sun, Dec 20, 2015 at 10:17 PM, Andy Shevchenko
<andy.shevchenko@xxxxxxxxx> wrote:

On Sun, Dec 20, 2015 at 8:49 PM, MÃns RullgÃrd <mans@xxxxxxxxx>
wrote:
I noticed thanks to DWC_PARAMS that burst size is hardcoded to 32
items on this board, however registers for SATA program it to 64. I
remember that I got no interrupt when I programmed transfer width
wrongly (64 bits against 32 bits) when I ported dw_dmac to be used
on
Intel SoCs.

One more thing, I have a patch to monitor DMA IO, we may check what
exactly the values are written / read in DMA. I can share it
tomorrow.

As promised the patch I have to debug IO of DW DMA. Didn't check though
if it applies cleanly on top of recent vanilla kernel.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.12.21 13:22:26 =~=~=~=~=~=~=~=~=~=~=~=

U-Boot 2015.a (May 16 2015 - 14:20:11)

CPU: AMCC PowerPC 460EX Rev. B at 1155 MHz (PLB=231 OPB=115 EBC=115)
No Security/Kasumi support
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
Internal PCI arbiter enabled
32 kB I-Cache 32 kB D-Cache
Board: Sam460ex/cr, PCIe 4x + SATA-2
I2C: ready
DRAM: 2 GiB (ECC not enabled, 462 MHz, CL4)
PCI: Bus Dev VenId DevId Class Int
00 04 1095 3512 0104 00
00 06 126f 0501 0380 00
PCIE1: successfully set as root-complex
02 00 1002 683f 0300 ff
Net: ppc_4xx_eth0
FPGA: Revision 03 (2010-10-07)
SM502: found
PERMD2:not found
VGA: 1
VESA: OK
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Using Canyonlands machine description
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 4.4.0-rc5-Sam460ex-dirty (root@julian-VirtualBox) (gcc version 4.8.2 (Ubuntu 4.8.2-16ubuntu3) ) #4 PREEMPT Mon Dec 21 13:13:19 AST 2015
[ 0.000000] Found legacy serial port 0 for /plb/opb/serial@ef600300
[ 0.000000] mem=4ef600300, taddr=4ef600300, irq=0, clk=11059200, speed=0
[ 0.000000] Found legacy serial port 1 for /plb/opb/serial@ef600400
[ 0.000000] mem=4ef600400, taddr=4ef600400, irq=0, clk=11059200, speed=0
[ 0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c0a34dc8, node_mem_map eefed000
[ 0.000000] DMA zone: 1536 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] HighMem zone: 327680 pages, LIFO batch:31
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
[ 0.000000] Kernel command line: root=/dev/sda8 console=ttyS0,115200 ignore_loglevel dw_dmac_core.dyndbg dw_dmac.dyndbg
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2068868K/2097152K available (6736K kernel code, 328K rwdata, 3232K rodata, 236K init, 368K bss, 28284K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffa00000..0xffc00000 : consistent mem
[ 0.000000] * 0xffa00000..0xffa00000 : early ioremap
[ 0.000000] * 0xf1000000..0xffa00000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[ 0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[ 0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[ 0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[ 0.000000] time_init: decrementer frequency = 1155.000010 MHz
[ 0.000000] time_init: processor frequency = 1155.000010 MHz
[ 0.000014] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x10a60dda894, max_idle_ns: 440795207041 ns
[ 0.000028] clocksource: timebase mult[dda520] shift[24] registered
[ 0.000039] clockevent: decrementer mult[93d70a53] shift[31] cpu[0]
[ 0.000148] Console: colour dummy device 80x25
[ 0.000180] pid_max: default: 32768 minimum: 301
[ 0.000281] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000293] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004078] devtmpfs: initialized
[ 0.006787] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.007177] xor: measuring software checksum speed
[ 0.016341] 8regs : 856.000 MB/sec
[ 0.026349] 8regs_prefetch: 784.000 MB/sec
[ 0.036382] 32regs : 1120.000 MB/sec
[ 0.046414] 32regs_prefetch: 996.000 MB/sec
[ 0.046421] xor: using function: 32regs (1120.000 MB/sec)
[ 0.046455] prandom: seed boundary self test passed
[ 0.048899] prandom: 100 self tests passed
[ 0.049441] NET: Registered protocol family 16
[ 0.052543] cpuidle: using governor ladder
[ 0.055576] cpuidle: using governor menu
[ 0.055976] 256k L2-cache enabled
[ 0.056060] PCIE0: Port disabled via device-tree
[ 0.056111] PCIE1: Checking link...
[ 0.056118] PCIE1: Device detected, waiting for link...
[ 0.056124] PCIE1: link is up !
[ 0.158408] PCI host bridge /plb/pciex@d20000000 (primary) ranges:
[ 0.158435] MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
[ 0.158450] MEM 0x0000000f00100000..0x0000000f001fffff -> 0x0000000000000000
[ 0.158460] IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
[ 0.158483] 4xx PCI DMA offset set to 0x00000000
[ 0.158489] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158495] DMA window size 0x0000000080000000
[ 0.158519] PCIE1: successfully set as root-complex
[ 0.158585] PCI host bridge /plb/pci@c0ec00000 (primary) ranges:
[ 0.158600] MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000
[ 0.158615] MEM 0x0000000c0ee00000..0x0000000c0eefffff -> 0x0000000000000000
[ 0.158625] IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000
[ 0.158639] 4xx PCI DMA offset set to 0x00000000
[ 0.158645] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158650] DMA window size 0x0000000080000000
[ 0.159137] PCI: Probing PCI hardware
[ 0.159238] PCI host bridge to bus 0000:80
[ 0.159257] pci_bus 0000:80: root bus resource [io 0xfffe0000-0xfffeffff] (bus address [0x0000-0xffff])
[ 0.159270] pci_bus 0000:80: root bus resource [mem 0xe80000000-0xeffffffff] (bus address [0x80000000-0xffffffff])
[ 0.159282] pci_bus 0000:80: root bus resource [mem 0xf00100000-0xf001fffff] (bus address [0x00000000-0x000fffff])
[ 0.159295] pci_bus 0000:80: root bus resource [bus 80-ff]
[ 0.159309] pci_bus 0000:80: busn_res: [bus 80-ff] end is updated to ff
[ 0.159346] pci 0000:80:00.0: [aaa1:bed1] type 01 class 0x060400
[ 0.159386] pci 0000:80:00.0: reg 0x10: [mem 0x00000000-0x7fffffff pref]
[ 0.159418] PCI: Hiding 4xx host bridge resources 0000:80:00.0
[ 0.159693] pci 0000:81:00.0: [1002:683f] type 00 class 0x030000
[ 0.159743] pci 0000:81:00.0: reg 0x10: [mem 0xea0000000-0xeafffffff 64bit pref]
[ 0.159764] pci 0000:81:00.0: reg 0x18: [mem 0xeb0000000-0xeb003ffff 64bit]
[ 0.159780] pci 0000:81:00.0: reg 0x20: [io 0xfffe2000-0xfffe20ff]
[ 0.159802] pci 0000:81:00.0: reg 0x30: [mem 0xf00100000-0xf0011ffff pref]
[ 0.159865] pci 0000:81:00.0: supports D1 D2
[ 0.159875] pci 0000:81:00.0: PME# supported from D1 D2 D3hot
[ 0.160025] pci 0000:81:00.1: [1002:aab0] type 00 class 0x040300
[ 0.160074] pci 0000:81:00.1: reg 0x10: [mem 0xf00100000-0xf00103fff 64bit]
[ 0.160159] pci 0000:81:00.1: supports D1 D2
[ 0.160286] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.160302] pci 0000:80:00.0: bridge window [io 0xfffe2000-0xfffe2fff]
[ 0.160313] pci 0000:80:00.0: bridge window [mem 0xea0000000-0xeb00fffff]
[ 0.160400] pci_bus 0000:80: busn_res: [bus 80-ff] end is updated to bf
[ 0.160491] PCI host bridge to bus 0001:00
[ 0.160504] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.160517] pci_bus 0001:00: root bus resource [mem 0xd80000000-0xdffffffff] (bus address [0x80000000-0xffffffff])
[ 0.160529] pci_bus 0001:00: root bus resource [mem 0xc0ee00000-0xc0eefffff] (bus address [0x00000000-0x000fffff])
[ 0.160539] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.160550] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.160577] pci 0001:00:04.0: [1095:3512] type 00 class 0x010400
[ 0.160601] pci 0001:00:04.0: reg 0x10: [io 0x1000-0x1007]
[ 0.160613] pci 0001:00:04.0: reg 0x14: [io 0x1008-0x100b]
[ 0.160626] pci 0001:00:04.0: reg 0x18: [io 0x1010-0x1017]
[ 0.160638] pci 0001:00:04.0: reg 0x1c: [io 0x1018-0x101b]
[ 0.160651] pci 0001:00:04.0: reg 0x20: [io 0x1020-0x102f]
[ 0.160664] pci 0001:00:04.0: reg 0x24: [mem 0xd80000000-0xd800001ff]
[ 0.160677] pci 0001:00:04.0: reg 0x30: [mem 0xc0ee00000-0xc0ee7ffff pref]
[ 0.160704] pci 0001:00:04.0: supports D1 D2
[ 0.160825] pci 0001:00:06.0: [126f:0501] type 00 class 0x038000
[ 0.160849] pci 0001:00:06.0: reg 0x10: [mem 0xd84000000-0xd87ffffff]
[ 0.160862] pci 0001:00:06.0: reg 0x14: [mem 0xd88000000-0xd881fffff]
[ 0.160898] pci 0001:00:06.0: supports D1 D2
[ 0.161072] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.161163] pci 0000:80:00.0: BAR 9: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161175] pci 0000:80:00.0: BAR 8: assigned [mem 0xe90000000-0xe900fffff]
[ 0.161186] pci 0000:80:00.0: BAR 7: assigned [io 0xfffe1000-0xfffe1fff]
[ 0.161202] pci 0000:81:00.0: BAR 0: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161223] pci 0000:81:00.0: BAR 2: assigned [mem 0xe90000000-0xe9003ffff 64bit]
[ 0.161240] pci 0000:81:00.0: BAR 6: assigned [mem 0xe90040000-0xe9005ffff pref]
[ 0.161253] pci 0000:81:00.1: BAR 0: assigned [mem 0xe90060000-0xe90063fff 64bit]
[ 0.161270] pci 0000:81:00.0: BAR 4: assigned [io 0xfffe1000-0xfffe10ff]
[ 0.161283] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.161294] pci 0000:80:00.0: bridge window [io 0xfffe1000-0xfffe1fff]
[ 0.161305] pci 0000:80:00.0: bridge window [mem 0xe90000000-0xe900fffff]
[ 0.161316] pci 0000:80:00.0: bridge window [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161329] pci_bus 0000:80: resource 4 [io 0xfffe0000-0xfffeffff]
[ 0.161339] pci_bus 0000:80: resource 5 [mem 0xe80000000-0xeffffffff]
[ 0.161348] pci_bus 0000:80: resource 6 [mem 0xf00100000-0xf001fffff]
[ 0.161358] pci_bus 0000:81: resource 0 [io 0xfffe1000-0xfffe1fff]
[ 0.161368] pci_bus 0000:81: resource 1 [mem 0xe90000000-0xe900fffff]
[ 0.161378] pci_bus 0000:81: resource 2 [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161393] pci 0001:00:06.0: BAR 0: assigned [mem 0xd80000000-0xd83ffffff]
[ 0.161406] pci 0001:00:06.0: BAR 1: assigned [mem 0xd84000000-0xd841fffff]
[ 0.161418] pci 0001:00:04.0: BAR 6: assigned [mem 0xd84200000-0xd8427ffff pref]
[ 0.161429] pci 0001:00:04.0: BAR 5: assigned [mem 0xd84280000-0xd842801ff]
[ 0.161441] pci 0001:00:04.0: BAR 4: assigned [io 0x1000-0x100f]
[ 0.161453] pci 0001:00:04.0: BAR 0: assigned [io 0x1010-0x1017]
[ 0.161464] pci 0001:00:04.0: BAR 2: assigned [io 0x1018-0x101f]
[ 0.161476] pci 0001:00:04.0: BAR 1: assigned [io 0x1020-0x1023]
[ 0.161487] pci 0001:00:04.0: BAR 3: assigned [io 0x1024-0x1027]
[ 0.161500] pci_bus 0001:00: resource 4 [io 0x0000-0xffff]
[ 0.161510] pci_bus 0001:00: resource 5 [mem 0xd80000000-0xdffffffff]
[ 0.161519] pci_bus 0001:00: resource 6 [mem 0xc0ee00000-0xc0eefffff]
[ 0.188264] raid6: int32x1 gen() 300 MB/s
[ 0.205418] raid6: int32x1 xor() 173 MB/s
[ 0.222443] raid6: int32x2 gen() 433 MB/s
[ 0.239493] raid6: int32x2 xor() 240 MB/s
[ 0.256583] raid6: int32x4 gen() 476 MB/s
[ 0.273662] raid6: int32x4 xor() 267 MB/s
[ 0.290719] raid6: int32x8 gen() 234 MB/s
[ 0.307890] raid6: int32x8 xor() 218 MB/s
[ 0.307897] raid6: using algorithm int32x4 gen() 476 MB/s
[ 0.307903] raid6: .... xor() 267 MB/s, rmw enabled
[ 0.307909] raid6: using intx1 recovery algorithm
[ 0.308208] vgaarb: device added: PCI:0000:81:00.0,decodes=io+mem,owns=none,locks=none
[ 0.308221] vgaarb: loaded
[ 0.308227] vgaarb: bridge control possible 0000:81:00.0
[ 0.308493] SCSI subsystem initialized
[ 0.308638] libata version 3.00 loaded.
[ 0.308879] usbcore: registered new interface driver usbfs
[ 0.308922] usbcore: registered new interface driver hub
[ 0.308978] usbcore: registered new device driver usb
[ 0.309073] pps_core: LinuxPPS API ver. 1 registered
[ 0.309081] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
[ 0.309108] PTP clock support registered
[ 0.309255] EDAC MC: Ver: 3.0.0
[ 0.309604] Advanced Linux Sound Architecture Driver Initialized.
[ 0.329537] DMA-API: preallocated 65536 debug entries
[ 0.329551] DMA-API: debugging enabled by kernel config
[ 0.329597] clocksource: Switched to clocksource timebase
[ 0.336198] NET: Registered protocol family 2
[ 0.336786] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336880] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 0.337220] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337333] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337399] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337744] NET: Registered protocol family 1
[ 0.338057] RPC: Registered named UNIX socket transport module.
[ 0.338067] RPC: Registered udp transport module.
[ 0.338073] RPC: Registered tcp transport module.
[ 0.338079] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338148] PCI: CLS mismatch (32 != 4), using 32 bytes
[ 0.338837] Could not remap bcsr
[ 0.341995] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 0.345046] futex hash table entries: 256 (order: 0, 7168 bytes)
[ 0.355229] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.355768] fuse init (API version 7.23)
[ 0.359937] async_tx: api initialized (async)
[ 0.360034] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.360050] io scheduler noop registered
[ 0.360191] io scheduler cfq registered (default)
[ 0.362260] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 0.362271] crc32: self tests passed, processed 225944 bytes in 892141 nsec
[ 0.363245] crc32c: CRC_LE_BITS = 64
[ 0.363254] crc32c: self tests passed, processed 225944 bytes in 446207 nsec
[ 0.429644] crc32_combine: 8373 self tests passed
[ 0.496237] crc32c_combine: 8373 self tests passed
[ 0.496288] glob: 64 self-tests passed, 0 failed
[ 0.534422] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.535200] console [ttyS0] disabled
[ 0.555345] serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a U6_16550A
[ 1.838037] console [ttyS0] enabled
[ 1.862154] serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a U6_16550A
[ 1.871999] console [ttyS0] disabled
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Using Canyonlands machine description
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 4.4.0-rc5-Sam460ex-dirty (root@julian-VirtualBox) (gcc version 4.8.2 (Ubuntu 4.8.2-16ubuntu3) ) #4 PREEMPT Mon Dec 21 13:13:19 AST 2015
[ 0.000000] Found legacy serial port 0 for /plb/opb/serial@ef600300
[ 0.000000] mem=4ef600300, taddr=4ef600300, irq=0, clk=11059200, speed=0
[ 0.000000] Found legacy serial port 1 for /plb/opb/serial@ef600400
[ 0.000000] mem=4ef600400, taddr=4ef600400, irq=0, clk=11059200, speed=0
[ 0.000000] Top of RAM: 0x80000000, Total RAM: 0x80000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c0a34dc8, node_mem_map eefed000
[ 0.000000] DMA zone: 1536 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 196608 pages, LIFO batch:31
[ 0.000000] HighMem zone: 327680 pages, LIFO batch:31
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
[ 0.000000] Kernel command line: root=/dev/sda8 console=ttyS0,115200 ignore_loglevel dw_dmac_core.dyndbg dw_dmac.dyndbg
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2068868K/2097152K available (6736K kernel code, 328K rwdata, 3232K rodata, 236K init, 368K bss, 28284K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffa00000..0xffc00000 : consistent mem
[ 0.000000] * 0xffa00000..0xffa00000 : early ioremap
[ 0.000000] * 0xf1000000..0xffa00000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[ 0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[ 0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[ 0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[ 0.000000] time_init: decrementer frequency = 1155.000010 MHz
[ 0.000000] time_init: processor frequency = 1155.000010 MHz
[ 0.000014] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x10a60dda894, max_idle_ns: 440795207041 ns
[ 0.000028] clocksource: timebase mult[dda520] shift[24] registered
[ 0.000039] clockevent: decrementer mult[93d70a53] shift[31] cpu[0]
[ 0.000148] Console: colour dummy device 80x25
[ 0.000180] pid_max: default: 32768 minimum: 301
[ 0.000281] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000293] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004078] devtmpfs: initialized
[ 0.006787] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.007177] xor: measuring software checksum speed
[ 0.016341] 8regs : 856.000 MB/sec
[ 0.026349] 8regs_prefetch: 784.000 MB/sec
[ 0.036382] 32regs : 1120.000 MB/sec
[ 0.046414] 32regs_prefetch: 996.000 MB/sec
[ 0.046421] xor: using function: 32regs (1120.000 MB/sec)
[ 0.046455] prandom: seed boundary self test passed
[ 0.048899] prandom: 100 self tests passed
[ 0.049441] NET: Registered protocol family 16
[ 0.052543] cpuidle: using governor ladder
[ 0.055576] cpuidle: using governor menu
[ 0.055976] 256k L2-cache enabled
[ 0.056060] PCIE0: Port disabled via device-tree
[ 0.056111] PCIE1: Checking link...
[ 0.056118] PCIE1: Device detected, waiting for link...
[ 0.056124] PCIE1: link is up !
[ 0.158408] PCI host bridge /plb/pciex@d20000000 (primary) ranges:
[ 0.158435] MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
[ 0.158450] MEM 0x0000000f00100000..0x0000000f001fffff -> 0x0000000000000000
[ 0.158460] IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
[ 0.158483] 4xx PCI DMA offset set to 0x00000000
[ 0.158489] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158495] DMA window size 0x0000000080000000
[ 0.158519] PCIE1: successfully set as root-complex
[ 0.158585] PCI host bridge /plb/pci@c0ec00000 (primary) ranges:
[ 0.158600] MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000
[ 0.158615] MEM 0x0000000c0ee00000..0x0000000c0eefffff -> 0x0000000000000000
[ 0.158625] IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000
[ 0.158639] 4xx PCI DMA offset set to 0x00000000
[ 0.158645] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158650] DMA window size 0x0000000080000000
[ 0.159137] PCI: Probing PCI hardware
[ 0.159238] PCI host bridge to bus 0000:80
[ 0.159257] pci_bus 0000:80: root bus resource [io 0xfffe0000-0xfffeffff] (bus address [0x0000-0xffff])
[ 0.159270] pci_bus 0000:80: root bus resource [mem 0xe80000000-0xeffffffff] (bus address [0x80000000-0xffffffff])
[ 0.159282] pci_bus 0000:80: root bus resource [mem 0xf00100000-0xf001fffff] (bus address [0x00000000-0x000fffff])
[ 0.159295] pci_bus 0000:80: root bus resource [bus 80-ff]
[ 0.159309] pci_bus 0000:80: busn_res: [bus 80-ff] end is updated to ff
[ 0.159346] pci 0000:80:00.0: [aaa1:bed1] type 01 class 0x060400
[ 0.159386] pci 0000:80:00.0: reg 0x10: [mem 0x00000000-0x7fffffff pref]
[ 0.159418] PCI: Hiding 4xx host bridge resources 0000:80:00.0
[ 0.159693] pci 0000:81:00.0: [1002:683f] type 00 class 0x030000
[ 0.159743] pci 0000:81:00.0: reg 0x10: [mem 0xea0000000-0xeafffffff 64bit pref]
[ 0.159764] pci 0000:81:00.0: reg 0x18: [mem 0xeb0000000-0xeb003ffff 64bit]
[ 0.159780] pci 0000:81:00.0: reg 0x20: [io 0xfffe2000-0xfffe20ff]
[ 0.159802] pci 0000:81:00.0: reg 0x30: [mem 0xf00100000-0xf0011ffff pref]
[ 0.159865] pci 0000:81:00.0: supports D1 D2
[ 0.159875] pci 0000:81:00.0: PME# supported from D1 D2 D3hot
[ 0.160025] pci 0000:81:00.1: [1002:aab0] type 00 class 0x040300
[ 0.160074] pci 0000:81:00.1: reg 0x10: [mem 0xf00100000-0xf00103fff 64bit]
[ 0.160159] pci 0000:81:00.1: supports D1 D2
[ 0.160286] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.160302] pci 0000:80:00.0: bridge window [io 0xfffe2000-0xfffe2fff]
[ 0.160313] pci 0000:80:00.0: bridge window [mem 0xea0000000-0xeb00fffff]
[ 0.160400] pci_bus 0000:80: busn_res: [bus 80-ff] end is updated to bf
[ 0.160491] PCI host bridge to bus 0001:00
[ 0.160504] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.160517] pci_bus 0001:00: root bus resource [mem 0xd80000000-0xdffffffff] (bus address [0x80000000-0xffffffff])
[ 0.160529] pci_bus 0001:00: root bus resource [mem 0xc0ee00000-0xc0eefffff] (bus address [0x00000000-0x000fffff])
[ 0.160539] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.160550] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.160577] pci 0001:00:04.0: [1095:3512] type 00 class 0x010400
[ 0.160601] pci 0001:00:04.0: reg 0x10: [io 0x1000-0x1007]
[ 0.160613] pci 0001:00:04.0: reg 0x14: [io 0x1008-0x100b]
[ 0.160626] pci 0001:00:04.0: reg 0x18: [io 0x1010-0x1017]
[ 0.160638] pci 0001:00:04.0: reg 0x1c: [io 0x1018-0x101b]
[ 0.160651] pci 0001:00:04.0: reg 0x20: [io 0x1020-0x102f]
[ 0.160664] pci 0001:00:04.0: reg 0x24: [mem 0xd80000000-0xd800001ff]
[ 0.160677] pci 0001:00:04.0: reg 0x30: [mem 0xc0ee00000-0xc0ee7ffff pref]
[ 0.160704] pci 0001:00:04.0: supports D1 D2
[ 0.160825] pci 0001:00:06.0: [126f:0501] type 00 class 0x038000
[ 0.160849] pci 0001:00:06.0: reg 0x10: [mem 0xd84000000-0xd87ffffff]
[ 0.160862] pci 0001:00:06.0: reg 0x14: [mem 0xd88000000-0xd881fffff]
[ 0.160898] pci 0001:00:06.0: supports D1 D2
[ 0.161072] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.161163] pci 0000:80:00.0: BAR 9: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161175] pci 0000:80:00.0: BAR 8: assigned [mem 0xe90000000-0xe900fffff]
[ 0.161186] pci 0000:80:00.0: BAR 7: assigned [io 0xfffe1000-0xfffe1fff]
[ 0.161202] pci 0000:81:00.0: BAR 0: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161223] pci 0000:81:00.0: BAR 2: assigned [mem 0xe90000000-0xe9003ffff 64bit]
[ 0.161240] pci 0000:81:00.0: BAR 6: assigned [mem 0xe90040000-0xe9005ffff pref]
[ 0.161253] pci 0000:81:00.1: BAR 0: assigned [mem 0xe90060000-0xe90063fff 64bit]
[ 0.161270] pci 0000:81:00.0: BAR 4: assigned [io 0xfffe1000-0xfffe10ff]
[ 0.161283] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.161294] pci 0000:80:00.0: bridge window [io 0xfffe1000-0xfffe1fff]
[ 0.161305] pci 0000:80:00.0: bridge window [mem 0xe90000000-0xe900fffff]
[ 0.161316] pci 0000:80:00.0: bridge window [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161329] pci_bus 0000:80: resource 4 [io 0xfffe0000-0xfffeffff]
[ 0.161339] pci_bus 0000:80: resource 5 [mem 0xe80000000-0xeffffffff]
[ 0.161348] pci_bus 0000:80: resource 6 [mem 0xf00100000-0xf001fffff]
[ 0.161358] pci_bus 0000:81: resource 0 [io 0xfffe1000-0xfffe1fff]
[ 0.161368] pci_bus 0000:81: resource 1 [mem 0xe90000000-0xe900fffff]
[ 0.161378] pci_bus 0000:81: resource 2 [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161393] pci 0001:00:06.0: BAR 0: assigned [mem 0xd80000000-0xd83ffffff]
[ 0.161406] pci 0001:00:06.0: BAR 1: assigned [mem 0xd84000000-0xd841fffff]
[ 0.161418] pci 0001:00:04.0: BAR 6: assigned [mem 0xd84200000-0xd8427ffff pref]
[ 0.161429] pci 0001:00:04.0: BAR 5: assigned [mem 0xd84280000-0xd842801ff]
[ 0.161441] pci 0001:00:04.0: BAR 4: assigned [io 0x1000-0x100f]
[ 0.161453] pci 0001:00:04.0: BAR 0: assigned [io 0x1010-0x1017]
[ 0.161464] pci 0001:00:04.0: BAR 2: assigned [io 0x1018-0x101f]
[ 0.161476] pci 0001:00:04.0: BAR 1: assigned [io 0x1020-0x1023]
[ 0.161487] pci 0001:00:04.0: BAR 3: assigned [io 0x1024-0x1027]
[ 0.161500] pci_bus 0001:00: resource 4 [io 0x0000-0xffff]
[ 0.161510] pci_bus 0001:00: resource 5 [mem 0xd80000000-0xdffffffff]
[ 0.161519] pci_bus 0001:00: resource 6 [mem 0xc0ee00000-0xc0eefffff]
[ 0.188264] raid6: int32x1 gen() 300 MB/s
[ 0.205418] raid6: int32x1 xor() 173 MB/s
[ 0.222443] raid6: int32x2 gen() 433 MB/s
[ 0.239493] raid6: int32x2 xor() 240 MB/s
[ 0.256583] raid6: int32x4 gen() 476 MB/s
[ 0.273662] raid6: int32x4 xor() 267 MB/s
[ 0.290719] raid6: int32x8 gen() 234 MB/s
[ 0.307890] raid6: int32x8 xor() 218 MB/s
[ 0.307897] raid6: using algorithm int32x4 gen() 476 MB/s
[ 0.307903] raid6: .... xor() 267 MB/s, rmw enabled
[ 0.307909] raid6: using intx1 recovery algorithm
[ 0.308208] vgaarb: device added: PCI:0000:81:00.0,decodes=io+mem,owns=none,locks=none
[ 0.308221] vgaarb: loaded
[ 0.308227] vgaarb: bridge control possible 0000:81:00.0
[ 0.308493] SCSI subsystem initialized
[ 0.308638] libata version 3.00 loaded.
[ 0.308879] usbcore: registered new interface driver usbfs
[ 0.308922] usbcore: registered new interface driver hub
[ 0.308978] usbcore: registered new device driver usb
[ 0.309073] pps_core: LinuxPPS API ver. 1 registered
[ 0.309081] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
[ 0.309108] PTP clock support registered
[ 0.309255] EDAC MC: Ver: 3.0.0
[ 0.309604] Advanced Linux Sound Architecture Driver Initialized.
[ 0.329537] DMA-API: preallocated 65536 debug entries
[ 0.329551] DMA-API: debugging enabled by kernel config
[ 0.329597] clocksource: Switched to clocksource timebase
[ 0.336198] NET: Registered protocol family 2
[ 0.336786] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336880] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 0.337220] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337333] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337399] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337744] NET: Registered protocol family 1
[ 0.338057] RPC: Registered named UNIX socket transport module.
[ 0.338067] RPC: Registered udp transport module.
[ 0.338073] RPC: Registered tcp transport module.
[ 0.338079] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338148] PCI: CLS mismatch (32 != 4), using 32 bytes
[ 0.338837] Could not remap bcsr
[ 0.341995] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 0.345046] futex hash table entries: 256 (order: 0, 7168 bytes)
[ 0.355229] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.355768] fuse init (API version 7.23)
[ 0.359937] async_tx: api initialized (async)
[ 0.360034] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.360050] io scheduler noop registered
[ 0.360191] io scheduler cfq registered (default)
[ 0.362260] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 0.362271] crc32: self tests passed, processed 225944 bytes in 892141 nsec
[ 0.363245] crc32c: CRC_LE_BITS = 64
[ 0.363254] crc32c: self tests passed, processed 225944 bytes in 446207 nsec
[ 0.429644] crc32_combine: 8373 self tests passed
[ 0.496237] crc32c_combine: 8373 self tests passed
[ 0.496288] glob: 64 self-tests passed, 0 failed
[ 0.534422] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.535200] console [ttyS0] disabled
[ 0.555345] serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a U6_16550A
[ 1.838037] console [ttyS0] enabled
[ 1.862154] serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a U6_16550A
[ 1.871999] console [ttyS0] disabled
[ 1.875668] 4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a 16550
[ 3.183169] console [ttyS0] enabled
[ 3.187294] 4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a 16550
[ 3.196669] Generic non-volatile memory driver v1.1
[ 3.201825] [drm] Initialized drm 1.1.0 20060810
[ 3.206512] [drm] radeon kernel modesetting enabled.
[ 3.212199] [drm] initializing kernel modesetting (VERDE 0x1002:0x683F 0x1545:0x7750).
[ 3.220185] [drm] register mmio base: 0xe90000000
[ 3.224923] [drm] register mmio size: 262144
[ 3.561022] ATOM BIOS: C44501
[ 3.564259] radeon 0000:81:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 3.573159] radeon 0000:81:00.0: GTT: 2048M 0x0000000040000000 - 0x00000000BFFFFFFF
[ 3.580827] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 3.585713] [drm] RAM width 128bits DDR
[ 3.589760] [TTM] Zone kernel: Available graphics memory: 379074 kiB
[ 3.596230] [TTM] Zone highmem: Available graphics memory: 1034434 kiB
[ 3.602762] [TTM] Initializing pool allocator
[ 3.607218] [drm] radeon: 1024M of VRAM memory ready
[ 3.612200] [drm] radeon: 2048M of GTT memory ready.
[ 3.617234] [drm] Loading verde Microcode
[ 3.621286] [drm] Internal thermal controller with fan control
[ 3.627355] [drm] probing gen 2 caps for device aaa1:bed1 = 18cc41/0
[ 3.681119] [drm] radeon: dpm initialized
[ 3.685345] radeon 0000:81:00.0: Direct firmware load for radeon/TAHITI_vce.bin failed with error -2
[ 3.694543] radeon 0000:81:00.0: radeon_vce: Can't load firmware "radeon/TAHITI_vce.bin"
[ 3.702692] [drm] GART: num cpu pages 524288, num gpu pages 524288
[ 3.719398] [drm] probing gen 2 caps for device aaa1:bed1 = 18cc41/0
[ 3.782990] [drm] PCIE GART of 2048M enabled (table at 0x0000000000277000).
[ 3.790272] radeon 0000:81:00.0: WB enabled
[ 3.794505] radeon 0000:81:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xedccec00
[ 3.804607] radeon 0000:81:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xedccec04
[ 3.814701] radeon 0000:81:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xedccec08
[ 3.824797] radeon 0000:81:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xedccec0c
[ 3.834892] radeon 0000:81:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xedccec10
[ 3.875472] radeon 0000:81:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xf5135a18
[ 3.885575] radeon 0000:81:00.0: VCE init error (-22).
[ 3.890726] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.897344] [drm] Driver supports precise vblank timestamp query.
[ 3.903450] radeon 0000:81:00.0: radeon: MSI limited to 32-bit
[ 3.909363] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 3.917632] radeon 0000:81:00.0: radeon: using MSI.
[ 3.922572] [drm] radeon: irq initialized.
[ 4.682096] [drm:r600_ring_test] *ERROR* radeon: ring 0 test failed (scratch(0x850C)=0xCAFEDEAD)
[ 4.690915] radeon 0000:81:00.0: disabling GPU acceleration
[ 4.900020] [drm] Radeon Display Connectors
[ 4.904266] [drm] Connector 0:
[ 4.907335] [drm] HDMI-A-1
[ 4.910226] [drm] HPD4
[ 4.912773] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
[ 4.920173] [drm] Encoders:
[ 4.923152] [drm] DFP1: INTERNAL_UNIPHY2
[ 4.927431] [drm] Connector 1:
[ 4.930495] [drm] DVI-I-1
[ 4.933298] [drm] HPD2
[ 4.935846] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[ 4.943246] [drm] Encoders:
[ 4.946215] [drm] DFP2: INTERNAL_UNIPHY
[ 4.950408] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 5.068678] [drm] fb mappable at 0x80678000
[ 5.072874] [drm] vram apper at 0x80000000
[ 5.076979] [drm] size 8294400
[ 5.080043] [drm] fb depth is 24
[ 5.083281] [drm] pitch is 7680
[ 5.361963] Console: switching to colour frame buffer device 240x67
[ 5.440884] radeon 0000:81:00.0: fb0: radeondrmfb frame buffer device
[ 5.449663] [drm] Initialized radeon 2.43.0 20080528 for 0000:81:00.0 on minor 0
[ 5.466378] brd: module loaded
[ 5.473901] loop: module loaded
[ 5.477284] sata_sil 0001:00:04.0: version 2.4
[ 5.481849] sata_sil 0001:00:04.0: Applying R_ERR on DMA activate FIS errata fix
[ 5.489939] scsi host0: sata_sil
[ 5.493468] scsi host1: sata_sil
[ 5.496859] ata1: SATA max UDMA/100 mmio m512@0xd84280000 tf 0xd84280080 irq 21
[ 5.504189] ata2: SATA max UDMA/100 mmio m512@0xd84280000 tf 0xd842800c0 irq 21
[ 5.512144] PPC 4xx OCP EMAC driver, version 3.54
[ 5.517411] MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
[ 5.523290] ZMII /plb/opb/emac-zmii@ef600d00 initialized
[ 5.528721] RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
[ 5.535888] TAH /plb/opb/emac-tah@ef601350 initialized
[ 5.541083] TAH /plb/opb/emac-tah@ef601450 initialized
[ 5.546496] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
[ 5.553645] eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:50:c2:80:d5:c5
[ 5.560540] eth0: found Generic MII PHY (0x00)
[ 5.565172] /plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode
[ 5.572263] eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:00:00:00:00:00
[ 5.579164] eth1: found Generic MII PHY (0x01)
[ 5.583661] PPP generic driver version 2.4.2
[ 5.588113] PPP BSD Compression module registered
[ 5.592835] PPP Deflate Compression module registered
[ 5.597897] NET: Registered protocol family 24
[ 5.602530] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.609222] ppc-of-ehci 4bffd0400.ehci: OF EHCI
[ 5.613930] ppc-of-ehci 4bffd0400.ehci: new USB bus registered, assigned bus number 1
[ 5.622735] ppc-of-ehci 4bffd0400.ehci: irq 31, io mem 0x4bffd0400
[ 5.634615] ppc-of-ehci 4bffd0400.ehci: USB 2.0 started, EHCI 1.00
[ 5.641001] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.647810] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.655038] usb usb1: Product: OF EHCI
[ 5.658796] usb usb1: Manufacturer: Linux 4.4.0-rc5-Sam460ex-dirty ehci_hcd
[ 5.665766] usb usb1: SerialNumber: PPC-OF USB
[ 5.670666] hub 1-0:1.0: USB hub found
[ 5.674481] hub 1-0:1.0: 1 port detected
[ 5.678723] ehci-pci: EHCI PCI platform driver
[ 5.683262] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.689634] ppc-of-ohci 4bffd0000.usb: OF OHCI
[ 5.694231] ppc-of-ohci 4bffd0000.usb: new USB bus registered, assigned bus number 2
[ 5.702026] ppc-of-ohci 4bffd0000.usb: irq 32, io mem 0x4bffd0000
[ 5.825623] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.865156] ata1.00: ATA-8: WDC WD5000AAKS-00V1A0, 05.01D05, max UDMA/133
[ 5.876598] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 5.894901] ata1.00: configured for UDMA/100
[ 5.917867] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 1D05 PQ: 0 ANSI: 5
[ 5.932790] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.938463] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 5.950753] sd 0:0:0:0: [sda] Write Protect is off
[ 5.960603] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.970679] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.988609] usb 1-1: new high-speed USB device number 2 using ppc-of-ehci
[ 6.005549] sda: RDSK (512) sda1 (DOS^G)(res 2 spb 1) sda2 (SFS^@)(res 2 spb 1) sda3 (SFS^@)(res 2 spb 1) sda4 (SFS^@)(res 2 spb 1) sda5 (SFS^@)(res 2 spb 1) sda6 (SFS^@)(res 2 spb 1) sda7 (NTFS)(res 2 spb 2) sda8 (EXT^C)(res 2 spb 1)
[ 6.047924] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.116959] usb 1-1: New USB device found, idVendor=0424, idProduct=2517
[ 6.129602] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 6.145694] hub 1-1:1.0: USB hub found
[ 6.152695] hub 1-1:1.0: 7 ports detected
[ 6.258622] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.290740] ata2.00: ATAPI: ASUS DRW-24B3ST i, 1.00, max UDMA/100
[ 6.307716] ata2.00: configured for UDMA/100
[ 6.323524] scsi 1:0:0:0: CD-ROM ASUS DRW-24B3ST i 1.00 PQ: 0 ANSI: 5
[ 6.366834] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 6.381600] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 6.393202] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 6.403804] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 6.430268] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.437081] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.444324] usb 1-1.1: new high-speed USB device number 3 using ppc-of-ehci
[ 6.451304] usb usb2: Product: OF OHCI
[ 6.455068] usb usb2: Manufacturer: Linux 4.4.0-rc5-Sam460ex-dirty ohci_hcd
[ 6.462086] usb usb2: SerialNumber: PPC-OF USB
[ 6.467082] hub 2-0:1.0: USB hub found
[ 6.470900] hub 2-0:1.0: 1 port detected
[ 6.475172] ohci-pci: OHCI PCI platform driver
[ 6.479913] usbcore: registered new interface driver usblp
[ 6.485551] usbcore: registered new interface driver usb-storage
[ 6.491794] usbcore: registered new interface driver usbserial
[ 6.497753] usbcore: registered new interface driver usbserial_generic
[ 6.504364] usbserial: USB Serial support registered for generic
[ 6.510683] mousedev: PS/2 mouse device common for all mice
[ 6.516362] i2c /dev entries driver
[ 6.522263] rtc-m41t80 8-0068: rtc core: registered m41t80 as rtc0
[ 6.529423] ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
[ 6.535701] ibm-iic 4ef600800.i2c: using standard (100 kHz) mode
[ 6.541796] md: linear personality registered for level -1
[ 6.547306] md: raid0 personality registered for level 0
[ 6.552626] md: raid1 personality registered for level 1
[ 6.558000] md: raid10 personality registered for level 10
[ 6.563753] md: raid6 personality registered for level 6
[ 6.569120] md: raid5 personality registered for level 5
[ 6.574449] md: raid4 personality registered for level 4
[ 6.580453] usb 1-1.1: New USB device found, idVendor=1a40, idProduct=0101
[ 6.587402] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@xxxxxxxxxx
[ 6.595886] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 6.603262] EDAC PPC4xx MC: v1.0.0
[ 6.606702] usb 1-1.1: Product: USB 2.0 Hub
[ 6.610898] EDAC PPC4xx MC: Reporting type: interrupt
[ 6.616403] hub 1-1.1:1.0: USB hub found
[ 6.620535] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.626314] hub 1-1.1:1.0: 4 ports detected
[ 6.630808] usbcore: registered new interface driver usbhid
[ 6.636453] usbhid: USB HID core driver
[ 6.640981] usbcore: registered new interface driver snd-usb-audio
[ 6.647367] usbcore: registered new interface driver snd-ua101
[ 6.653487] usbcore: registered new interface driver snd-usb-usx2y
[ 6.660061] ipip: IPv4 over IPv4 tunneling driver
[ 6.665283] Initializing XFRM netlink socket
[ 6.670342] NET: Registered protocol family 10
[ 6.675969] sit: IPv6 over IPv4 tunneling driver
[ 6.681111] NET: Registered protocol family 17
[ 6.685616] NET: Registered protocol family 15
[ 6.690323] Running MSI bitmap self-tests ...
[ 6.696369] Key type encrypted registered
[ 6.702025] rtc-m41t80 8-0068: setting system clock to 2015-12-21 13:22:59 UTC (1450704179)
[ 6.710587] ALSA device list:
[ 6.713601] No soundcards found.
[ 6.717533] md: Waiting for all devices to be available before autodetect
[ 6.724368] md: If you don't use raid, use raid=noautodetect
[ 6.730067] usb 1-1.2: new low-speed USB device number 4 using ppc-of-ehci
[ 6.737571] md: Autodetecting RAID arrays.
[ 6.741790] md: Scanned 0 and added 0 devices.
[ 6.746335] md: autorun ...
[ 6.749186] md: ... autorun DONE.
[ 6.777002] EXT4-fs (sda8): mounting ext3 file system using the ext4 subsystem
[ 6.794151] EXT4-fs (sda8): INFO: recovery required on readonly filesystem
[ 6.801071] EXT4-fs (sda8): write access will be enabled during recovery
[ 6.841802] usb 1-1.2: New USB device found, idVendor=04f2, idProduct=0116
[ 6.848867] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.857020] usb 1-1.2: Product: USB Keyboard
[ 6.861475] usb 1-1.2: Manufacturer: CHICONY
[ 6.877190] input: CHICONY USB Keyboard as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.2/1-1.2:1.0/0003:04F2:0116.0001/input/input0
[ 6.940637] usb 1-1.1.1: new full-speed USB device number 5 using ppc-of-ehci
[ 6.948358] hid-generic 0003:04F2:0116.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-PPC-OF USB-1.2/input0
[ 7.048062] usb 1-1.1.1: New USB device found, idVendor=0d8c, idProduct=000c
[ 7.055647] usb 1-1.1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 7.064556] usb 1-1.1.1: Product: C-Media USB Audio Device
[ 7.100633] input: C-Media USB Audio Device as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.3/0003:0D8C:000C.0002/input/input1
[ 7.114624] usb 1-1.6: new full-speed USB device number 6 using ppc-of-ehci
[ 7.172929] hid-generic 0003:0D8C:000C.0002: input,hidraw1: USB HID v1.00 Device [C-Media USB Audio Device ] on usb-PPC-OF USB-1.1.1/input3
[ 7.210292] usb 1-1.6: New USB device found, idVendor=046d, idProduct=c52b
[ 7.217335] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.224812] usb 1-1.6: Product: USB Receiver
[ 7.229128] usb 1-1.6: Manufacturer: Logitech
[ 7.237511] input: Logitech USB Receiver as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.6/1-1.6:1.0/0003:046D:C52B.0003/input/input2
[ 7.300884] hid-generic 0003:046D:C52B.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input0
[ 7.318919] input: Logitech USB Receiver as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.6/1-1.6:1.1/0003:046D:C52B.0004/input/input3
[ 7.382959] hid-generic 0003:046D:C52B.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input1
[ 7.400708] hid-generic 0003:046D:C52B.0005: hidraw4: USB HID v1.11 Device [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input2
[ 7.412289] random: nonblocking pool is initialized
[ 7.490621] usb 1-1.7: new high-speed USB device number 7 using ppc-of-ehci
[ 7.589147] usb 1-1.7: New USB device found, idVendor=0424, idProduct=2240
[ 7.596076] usb 1-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7.603429] usb 1-1.7: Product: Ultra Fast Media
[ 7.608182] usb 1-1.7: Manufacturer: Generic
[ 7.612477] usb 1-1.7: SerialNumber: 000000225001
[ 7.617802] usb-storage 1-1.7:1.0: USB Mass Storage device detected
[ 7.624332] scsi host2: usb-storage 1-1.7:1.0
[ 7.969307] EXT4-fs (sda8): recovery complete
[ 7.985307] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[ 7.993026] VFS: Mounted root (ext3 filesystem) readonly on device 8:8.
[ 8.026467] devtmpfs: mounted
[ 8.030022] Freeing unused kernel memory: 236K (c09bf000 - c09fa000)
[ 8.629822] scsi 2:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0
[ 8.638965] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8.646517] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 9.070838] systemd[1]: Failed to insert module 'kdbus': Function not implemented
[ 9.151205] systemd[1]: systemd 228 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 9.169773] systemd[1]: Detected architecture ppc.

Welcome to Ubuntu 16.04!

[ 9.207679] systemd[1]: Set hostname to <Sam460ex>.
[ 9.416679] systemd-fstab-generator[118]: Mount point is not a valid path, ignoring.
[ 10.219579] systemd[112]: /lib/systemd/system-generators/systemd-fstab-generator terminated by signal ABRT.
[ 10.558232] systemd[1]: Reached target User and Group Name Lookups.
[ OK ] Reached target User and Group Name Lookups.
[ 10.642367] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 10.656027] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 10.667028] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 10.677781] systemd[1]: Reached target Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 10.689778] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 10.700003] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 10.717112] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 10.729945] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 10.745677] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
[ 10.765121] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 10.778983] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 10.791793] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 10.801968] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 10.817971] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 10.829793] systemd[1]: Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems (Pre).
[ 10.843774] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 10.857015] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 10.871122] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 10.887075] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 10.907992] systemd[1]: Started Read required files in advance.
[ OK ] Started Read required files in advance.
[ 10.996210] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 11.013015] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 11.040005] systemd[1]: Starting Uncomplicated firewall...
Starting Uncomplicated firewall...
[ 11.057836] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 11.083761] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 11.198583] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ 11.222547] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 11.386006] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[ 11.402045] systemd[1]: Failed to start Load Kernel Modules.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[ 11.424026] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[ 11.431893] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[ 11.470141] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 11.487493] systemd[1]: Mounting Configuration File System...
Mounting Configuration File System...
[ 11.507993] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 11.566305] systemd[1]: Started Uncomplicated firewall.
[ OK ] Started Uncomplicated firewall.
[ 11.634865] systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
[ 11.669957] systemd[1]: Mounted Configuration File System.
[ OK ] Mounted Configuration File System.
[ 11.683899] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Debug File System.
[ 11.695938] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 11.711875] systemd[1]: Started Apply Kernel Variables.
[ OK ] Started Apply Kernel Variables.
[ 11.932002] systemd[1]: ureadahead.service: Main process exited, code=exited, status=5/NOTINSTALLED
[ 11.950894] systemd[1]: ureadahead.service: Unit entered failed state.
[ 11.957552] systemd[1]: ureadahead.service: Failed with result 'exit-code'.
[ 12.065338] systemd[1]: Started Create Static Device Nodes in /dev.
[ OK ] Started Create Static Device Nodes in /dev.
[ 12.115525] systemd[1]: Starting udev Kernel Device Manager...
Starting udev Kernel Device Manager...
[ 12.293388] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Started udev Kernel Device Manager.
Starting File System Check on Root Device...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Started File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[ 13.826873] EXT4-fs (sda8): re-mounted. Opts: errors=remount-ro
[ 13.836981] systemd-remount[154]: unhandled signal 11 at 0000000c nip 205309a4 lr 2053071c code 30001
[FAILED] Failed to start Remount Root and Kernel File Systems.
See 'systemctl status systemd-remount-fs.service' for details.
Starting Load/Save Random Seed...
Starting Flush Journal to Persistent Storage...
[ OK ] Reached target Local File Systems (Pre).
Starting udev Coldplug all Devices...
[ OK ] Started Load/Save Random Seed.
[ 14.089432] systemd-journald[132]: Received request to flush runtime journal from PID 1
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 15.404403] sata-dwc 4bffd1000.sata: no dma-channel property set. Use channel 0
[ OK ] Found device /dev/ttyS0.
[ 15.506671] sata-dwc 4bffd1000.sata: ioremap done for SATA register address
[ 15.584664] sata-dwc 4bffd1000.sata: id 0, controller version 1.82
[ 15.636719] sata-dwc 4bffd1000.sata: DMA initialized
[ 15.678638] sata-dwc 4bffd1000.sata: SATA DMA registers=0xf6a20800
[ 15.709687] sata-dwc 4bffd1000.sata: sata_dwc_enable_interrupts: INTMR = 0x0000000f, ERRMR = 0x0fff0f03
[ 15.789715] sata-dwc 4bffd1000.sata: sata_dwc_port_start: port_no=0
[ 15.828059] sata-dwc 4bffd1000.sata: sata_dwc_port_start: clearing TXCHEN, RXCHEN in DMAC
[ 15.888672] sata-dwc 4bffd1000.sata: sata_dwc_port_start: setting burst size in DBTSR
[ 15.947417] sata-dwc 4bffd1000.sata: sata_dwc_port_start: done
[ 16.011861] scsi host3: sata-dwc
[ 16.040874] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000000
[ OK ] Created slice system-ifup.slice.
[ 16.204644] ata3: SATA max UDMA/133 irq 36
[ 16.232743] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000000
[ 16.247677] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000000
[ OK ] Found device /sys/subsystem/ne[ 16.268489] sata-dwc 4bffd1000.sata: sata_dwc_scr_write: id=3 reg=2 val=val=0x00000301
t/devices/eth0.
[ 16.286707] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000301
[ 16.305668] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000301
[ 16.320664] sata-dwc 4bffd1000.sata: sata_dwc_scr_write: id=3 reg=2 val=val=0x00000300
[ 16.545650] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000300
[ 16.560655] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.583646] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.603626] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.623639] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.644628] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ OK ] Reached target Sound Card.
[ 16.674903] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.687697] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=1 val=val=0x04050002
[ 16.705642] sata-dwc 4bffd1000.sata: sata_dwc_scr_write: id=3 reg=1 val=val=0x04050002
[ 16.725638] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.740306] sata-dwc 4bffd1000.sata: sata_dwc_enable_interrupts: INTMR = 0x0000000f, ERRMR = 0x0fff0f03
[ 16.765630] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ OK ] Found device WDC_WD5000AAKS-00V1A0 NTFS.[ 16.786271] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123

[ 16.804631] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.822701] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=1 val=val=0x00000000
[ 16.838673] sata-dwc 4bffd1000.sata: sata_dwc_scr_write: id=3 reg=1 val=val=0x00000000
[ 16.855642] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
Mounting /media/NTFS...
[ 16.884718] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=2 val=val=0x00000300
[ 16.910686] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.931697] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 16.944664] sata-dwc 4bffd1000.sata: sata_dwc_scr_read: id=3 reg=0 val=val=0x00000123
[ 16.967666] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue ap id=3 cmd(0xec)=IDENTIFY DEVICE qc tag=31 prot=ATA PIO ap active_tag=0x0000001f ap sactive=0x00000000
[ 16.981853] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 16.990731] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=eca27c88 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.002473] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 17.009793] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xeca27c88, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 17.093717] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue ap id=3 cmd(0x27)=READ NATIVE MAX ADDRESS EXT qc tag=31 prot=ATA no data ap active_tag=0x0000001f ap sactive=0x00000000
[ 17.109292] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=none n_elem=0
[ 17.117563] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg= (null) nelem=0 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.129306] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0x (null), count: 0 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 17.152364] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=31
[ 17.159776] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA no data
[ 17.168393] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 17.175095] sata-dwc 4bffd1000.sata: QC complete cmd=0x27 status=0x00 ata3: protocol=1
[ 17.213676] ata3.00: ATA-8: WDC WD5000AAKS-00UU3A0, 01.03B01, max UDMA/133
[ 17.228627] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 1/32)
[ 17.241702] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue ap id=3 cmd(0xef)=SET FEATURES qc tag=31 prot=ATA no data ap active_tag=0x0000001f ap sactive=0x00000000
[ 17.255976] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=none n_elem=0
[ 17.264246] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg= (null) nelem=0 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.275991] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0x (null), count: 0 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 17.341690] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue ap id=3 cmd(0xec)=IDENTIFY DEVICE qc tag=31 prot=ATA PIO ap active_tag=0x0000001f ap sactive=0x00000000
[ 17.355880] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 17.364759] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=eca27bb8 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.376500] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 17.383813] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xeca27bb8, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 17.499702] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue ap id=3 cmd(0x27)=READ NATIVE MAX ADDRESS EXT qc tag=31 prot=ATA no data ap active_tag=0x0000001f ap sactive=0x00000000
[ 17.515281] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=none n_elem=0
[ 17.523552] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg= (null) nelem=0 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.535296] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0x (null), count: 0 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 17.548378] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=31
[ 17.555780] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA no data
[ 17.564400] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 17.571101] sata-dwc 4bffd1000.sata: QC complete cmd=0x27 status=0x00 ata3: protocol=1
[ 17.677085] ata3.00: configured for UDMA/133
[ 17.699982] scsi 3:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 3B01 PQ: 0 ANSI: 5
[ 17.714268] sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 17.723760] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 17.735790] sd 3:0:0:0: [sdc] Write Protect is off
[ 17.749707] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 17.760878] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.784490] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 17.793381] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd58100 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 17.805120] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c313000 sg_len=4096
[ 17.813306] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 17.822363] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd58100, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 17.835321] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 17.845353] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 17.858247] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 17.866268] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 17.872110] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 17.883592] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 17.892299] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x0 lbah: 0x0
[ 17.900659] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 17.910800] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 17.919076] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 17.926387] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 17.934660] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 17.941370] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 18.034681] sdc: RDSK (512) sdc1 (DOS^G)(res 2 spb 1) sdc2 (SFS^@)(res 2 spb 1)
[ 18.053050] sd 3:0:0:0: [sdc] Attached SCSI disk
[ OK ] Mounted /media/NTFS.
[ OK ] Reached target Local File Systems.
Starting LSB: AppArmor initialization...
Starting Clean up any mess left by 0dns-up...
Starting Wait for all "auto" /etc/n... up for network-online.target...
Starting Create Volatile Files and Directories...
Starting Tell Plymouth To Write Out Runtime Data...
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Tell Plymouth To Write Out Runtime Data.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Clean up any mess left by 0dns-up.
Starting Nameserver information manager...
[ OK ] Started Nameserver information manager.
[ OK ] Started LSB: AppArmor initialization.
Starting LSB: Raise network interfaces....
[ OK ] Started ifup for eth0.
[ 20.489120] eth0: link is up, 1000 FDX, pause enabled
Starting LSB: start Samba SMB/CIFS daemon (smbd)...
[ 22.740823] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 22.749716] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd58100 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 22.761455] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 22.768775] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd58100, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 22.782573] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 22.789894] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA PIO
[ 22.847073] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 22.855966] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd58100 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 22.867704] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c1bd000 sg_len=4096
[ 22.875882] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 22.884938] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd58100, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 22.897896] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 22.907918] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 22.947476] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 22.955493] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 22.961336] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 22.972818] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 22.981524] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x80 lbam: 0x5f lbah: 0x38
[ 22.990145] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 23.000389] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.008665] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.015978] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.024251] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.030960] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.040892] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.049785] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd58100 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.061525] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c1bc000 sg_len=4096
[ 23.069710] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 23.078766] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd58100, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 23.091726] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 23.101746] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 23.110957] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 23.118964] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 23.124807] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 23.136289] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 23.144988] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x20 lbam: 0x60 lbah: 0x38
[ 23.153608] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 23.163835] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.172111] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.179424] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.187696] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.194397] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.231806] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.240697] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd58e00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.252435] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb8d000 sg_len=4096
[ 23.260614] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 23.269669] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd58e00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 23.282627] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 23.292649] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 23.301876] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 23.309883] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 23.315719] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 23.327201] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 23.335908] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x0 lbah: 0x0
[ 23.344268] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 23.354385] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.362657] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.369970] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.378234] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.384944] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.431784] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.440679] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.452418] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb8c000 sg_len=4096
[ 23.460605] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 23.469661] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 23.482620] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 23.492640] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 23.501853] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 23.509866] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 23.515710] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 23.527192] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 23.535899] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x8 lbam: 0x0 lbah: 0x0
[ 23.544260] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 23.554386] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.562657] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.569970] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.578234] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.584945] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.608755] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.617650] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.629389] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2bb19000 sg_len=4096
[ 23.637575] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 23.646631] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 23.659590] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 23.669610] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 23.678841] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 23.686853] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 23.692689] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 23.704172] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 23.712879] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x28 lbam: 0x60 lbah: 0x38
[ 23.721499] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 23.731702] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.739981] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.747296] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.755561] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.762271] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.802365] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.811261] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.823000] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b885000 sg_len=4096
[ 23.831186] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 23.840242] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 23.853201] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 23.863222] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 23.880273] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 23.888297] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 23.894140] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 23.905621] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 23.914328] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x28 lbam: 0x5f lbah: 0x38
[ 23.922949] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 23.933174] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 23.941449] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 23.948763] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 23.957028] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 23.963737] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 23.972724] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 23.981616] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 23.993356] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c12a000 sg_len=4096
[ 24.001542] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.010598] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.023557] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.033577] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.042784] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.050795] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.056630] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.068113] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.076819] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0xf0 lbam: 0x5f lbah: 0x38
[ 24.085440] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 24.095650] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 24.103924] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 24.111238] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 24.119510] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 24.126212] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 24.165184] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 24.174074] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 24.185813] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca00000 sg_len=4096
[ 24.193999] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.203055] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.216013] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.226034] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.235280] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.243286] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.249130] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.260613] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.269320] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x30 lbam: 0x5f lbah: 0x38
[ 24.277940] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 24.288143] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 24.296415] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 24.303729] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 24.312002] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 24.318712] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 24.350760] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 24.359654] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 24.371394] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c149000 sg_len=4096
[ 24.379572] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.388628] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.401586] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.411608] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.420827] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.428833] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.434669] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.446151] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.454858] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0xa0 lbam: 0x5e lbah: 0x38
[ 24.463478] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 24.473691] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 24.481963] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 24.489275] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 24.497541] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 24.504250] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 24.528741] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 24.537632] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 24.549371] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb82000 sg_len=4096
[ 24.557558] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.566614] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.579573] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.589593] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.603174] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.611196] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.617039] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.628521] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.637228] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0xe0 lbam: 0x5d lbah: 0x38
[ 24.645848] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 24.656075] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 24.664349] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 24.671663] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 24.679936] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 24.686647] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 24.698906] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 24.707798] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 24.719536] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2badc000 sg_len=4096
[ 24.727713] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.736770] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.749729] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.759750] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.768978] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.776983] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.782820] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.794302] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.803009] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x88 lbam: 0x5d lbah: 0x38
[ 24.811629] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 24.821844] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 24.830114] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 24.837427] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 24.845700] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 24.852410] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 24.890605] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 24.899499] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 24.911238] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cbef000 sg_len=4096
[ 24.919424] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 24.928480] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 24.941438] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 24.951459] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 24.960693] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 24.968703] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 24.974539] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 24.986021] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 24.994728] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x50 lbam: 0x5d lbah: 0x38
[ 25.003347] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.013562] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.021832] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.029146] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.037418] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.044128] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.076902] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.085791] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.097531] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cbee000 sg_len=4096
[ 25.105708] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 25.114765] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 25.127724] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 25.137744] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 25.151095] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 25.159112] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 25.164956] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 25.176438] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 25.185144] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0xa0 lbam: 0x5c lbah: 0x38
[ 25.193765] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.203990] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.212266] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.219580] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.227853] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.234563] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.243191] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.252075] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.263816] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca89000 sg_len=4096
[ 25.272002] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 25.281058] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 25.294017] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 25.304036] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 25.313262] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 25.321272] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 25.327107] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 25.338590] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 25.347297] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x60 lbam: 0x5c lbah: 0x38
[ 25.355916] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.366119] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.374392] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.381706] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.389979] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.396690] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.438584] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.447477] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.459215] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca88000 sg_len=4096
[ 25.467402] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 25.476457] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 25.489416] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 25.499437] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 25.508671] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 25.516680] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 25.522525] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 25.534007] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 25.542714] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x50 lbam: 0x5c lbah: 0x38
[ 25.551335] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.561548] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.569819] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.577132] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.585404] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.592106] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.621013] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.629907] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.641646] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb53000 sg_len=4096
[ 25.649832] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 25.658887] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 25.671847] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 25.681868] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 25.691111] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 25.699120] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 25.704963] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 25.716446] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 25.725144] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x78 lbam: 0x5c lbah: 0x38
[ 25.733764] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.743967] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.752240] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.759554] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.767826] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.774536] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.798465] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.807364] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.819102] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb52000 sg_len=4096
[ 25.827280] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 25.836336] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 25.849294] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 25.859316] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 25.876534] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 25.884555] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 25.890399] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 25.901881] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 25.910587] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x20 lbam: 0x54 lbah: 0x38
[ 25.919207] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 25.929423] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 25.937690] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 25.945005] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 25.953269] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 25.959979] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 25.969954] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 25.978848] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 25.990587] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c311000 sg_len=4096
[ 25.998774] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.007829] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 26.020788] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 26.030808] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 26.040024] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 26.048034] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 26.053870] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 26.065353] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 26.074059] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x8 lbah: 0x0
[ 26.082419] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 26.092552] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 26.100825] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 26.108139] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 26.116412] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 26.123122] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 26.159801] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 26.168692] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 26.180430] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c310000 sg_len=4096
[ 26.188617] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.197673] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 26.210631] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 26.220652] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 26.229869] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 26.237878] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 26.243713] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 26.255197] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 26.263903] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x18 lbam: 0x0 lbah: 0x0
[ 26.272350] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 26.282465] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 26.290739] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 26.298052] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 26.306324] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 26.313026] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 26.351992] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 26.360888] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 26.372627] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c34b000 sg_len=4096
[ 26.380813] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.389869] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 26.402827] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 26.412849] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 26.422077] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 26.430083] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 26.435918] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 26.447401] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 26.456108] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x38 lbam: 0x0 lbah: 0x0
[ 26.464554] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 26.474691] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 26.482961] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 26.490274] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 26.498539] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 26.505248] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 26.534092] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 26.542988] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 26.554727] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c34a000 sg_len=4096
[ 26.562905] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.571961] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 26.584920] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 26.594940] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 26.604186] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 26.612192] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 26.618028] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 26.629511] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 26.638217] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x78 lbam: 0x0 lbah: 0x0
[ 26.646664] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 26.656781] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 26.665052] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 26.672367] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 26.680638] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 26.687340] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 26.715551] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=14
[ 26.724534] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec92dc00 nelem=14 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 26.736359] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ba96000 sg_len=4096
[ 26.744546] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.753598] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c24b000 sg_len=4096
[ 26.761775] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.770820] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c24a000 sg_len=4096
[ 26.778997] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.788043] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2ca5d000 sg_len=4096
[ 26.796219] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.805264] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2ca5c000 sg_len=4096
[ 26.813442] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.822487] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2caa5000 sg_len=4096
[ 26.830664] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.839709] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2caa4000 sg_len=4096
[ 26.847887] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.856931] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c992000 sg_len=4096
[ 26.865108] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.874154] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2ca1c000 sg_len=4096
[ 26.882331] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.891376] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2badd000 sg_len=4096
[ 26.899552] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 26.908598] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2c902000 sg_len=8192
[ 26.916862] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 26.925907] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2c9d0000 sg_len=8192
[ 26.934171] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 26.943216] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2cba0000 sg_len=8192
[ 26.951480] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 26.960525] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=13 sg_addr=0x2cb9e000 sg_len=8192
[ 26.968789] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 26.977838] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec92dc00, count: 14 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 14
[ 26.990970] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 27.000991] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 27.010259] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 27.018269] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 27.024113] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 27.035596] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 27.044302] sata-dwc 4bffd1000.sata: feature: 0x90 nsect: 0x0 lbal: 0x80 lbam: 0x0 lbah: 0x0
[ 27.052749] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 27.063151] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 27.071426] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 27.078738] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 27.087011] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 27.093720] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 27.101780] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 27.110659] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 27.122401] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c169000 sg_len=4096
[ 27.130586] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.139634] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 27.152593] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 27.162612] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 27.171828] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 27.179840] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 27.185683] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 27.197167] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 27.205873] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x10 lbam: 0x0 lbah: 0x0
[ 27.214319] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 27.224442] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 27.232717] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 27.240030] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 27.248295] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 27.255005] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 27.263457] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=3
[ 27.272344] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=3 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 27.284085] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c168000 sg_len=4096
[ 27.292271] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.301324] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2b933000 sg_len=4096
[ 27.309501] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.318546] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b932000 sg_len=4096
[ 27.326723] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.335771] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 3 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 3
[ 27.348730] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 27.358750] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 27.367977] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 27.375985] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 27.381820] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 27.393303] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 27.402001] sata-dwc 4bffd1000.sata: feature: 0x18 nsect: 0x0 lbal: 0x20 lbam: 0x0 lbah: 0x0
[ 27.410448] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 27.420593] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 27.428864] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 27.436177] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 27.444440] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 27.451142] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 27.459252] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=7
[ 27.468133] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=7 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 27.479874] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ba7d000 sg_len=4096
[ 27.488052] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.497105] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2ba7c000 sg_len=4096
[ 27.505282] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.514327] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c10d000 sg_len=4096
[ 27.522504] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.531550] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c10c000 sg_len=4096
[ 27.539726] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.548772] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c1d5000 sg_len=4096
[ 27.556948] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.565994] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c1d4000 sg_len=4096
[ 27.574171] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.583217] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2ba97000 sg_len=4096
[ 27.591401] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 27.600449] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 7 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 7
[ 27.613408] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 27.623428] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 27.632634] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 27.640647] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 27.646482] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 27.657964] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 27.666663] sata-dwc 4bffd1000.sata: feature: 0x38 nsect: 0x0 lbal: 0x40 lbam: 0x0 lbah: 0x0
[ 27.675110] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 27.685315] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 27.693586] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 27.700899] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 27.709172] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 27.715882] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 27.725334] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=15
[ 27.734317] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec92dc00 nelem=15 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 27.746142] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0aa000 sg_len=8192
[ 27.754329] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.763381] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2cbe2000 sg_len=8192
[ 27.771558] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.780604] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c196000 sg_len=8192
[ 27.788781] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.797827] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c3a6000 sg_len=8192
[ 27.806012] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.815057] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2b972000 sg_len=8192
[ 27.823243] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.832288] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c9fa000 sg_len=8192
[ 27.840464] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.849510] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c092000 sg_len=8192
[ 27.857687] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.866740] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2caaa000 sg_len=8192
[ 27.874918] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.883971] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2cb16000 sg_len=8192
[ 27.892149] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.901194] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2cad4000 sg_len=8192
[ 27.909380] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.918434] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2ca90000 sg_len=8192
[ 27.926706] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.935761] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2c116000 sg_len=8192
[ 27.944032] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.953077] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2c180000 sg_len=8192
[ 27.961341] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.970386] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=13 sg_addr=0x2ca10000 sg_len=8192
[ 27.978650] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 27.987695] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=14 sg_addr=0x2b934000 sg_len=8192
[ 27.995959] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.005008] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec92dc00, count: 15 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 15
[ 28.018140] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 28.028161] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 28.037401] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 28.045413] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 28.051257] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 28.062740] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 28.071446] sata-dwc 4bffd1000.sata: feature: 0xf0 nsect: 0x0 lbal: 0x10 lbam: 0x1 lbah: 0x0
[ 28.079893] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 28.090704] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 28.098991] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 28.106308] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 28.114580] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 28.121291] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 28.270192] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=11
[ 28.279169] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec92d400 nelem=11 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 28.290995] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b936000 sg_len=8192
[ 28.299182] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.308233] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c3a0000 sg_len=16384
[ 28.316498] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.325551] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.334596] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c34c000 sg_len=16384
[ 28.342860] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.351906] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.360951] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c1dc000 sg_len=16384
[ 28.369222] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.378268] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.387313] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c1d0000 sg_len=16384
[ 28.395577] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.404623] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.413668] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c340000 sg_len=12288
[ 28.421940] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.430986] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.440031] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c0ed000 sg_len=4096
[ 28.448207] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.457253] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c104000 sg_len=8192
[ 28.465430] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.474476] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2c10a000 sg_len=8192
[ 28.482660] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.491706] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2c0ce000 sg_len=8192
[ 28.499882] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.508928] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2c334000 sg_len=16384
[ 28.517279] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.526323] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.535373] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec92d400, count: 11 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 17
[ 28.548505] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 28.558526] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 28.567782] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 28.575794] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 28.581631] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 28.593113] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 28.601819] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x2 lbah: 0x0
[ 28.610180] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 28.620776] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 28.629058] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 28.636369] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 28.644641] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 28.651351] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 28.708030] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=11
[ 28.717009] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec92d400 nelem=11 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 28.728834] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb18000 sg_len=16384
[ 28.737107] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.746159] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.755204] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c0c8000 sg_len=16384
[ 28.763467] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.772513] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.781559] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c324000 sg_len=16384
[ 28.789831] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.798884] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.807930] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c314000 sg_len=16384
[ 28.816194] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.825239] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.834284] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c110000 sg_len=12288
[ 28.842557] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.851602] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.860647] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2bb0c000 sg_len=4096
[ 28.868833] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.877878] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c0ec000 sg_len=4096
[ 28.886055] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.895100] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c0ee000 sg_len=8192
[ 28.903278] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 28.911116] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.920161] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.929206] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2c178000 sg_len=8192
[ 28.937383] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 28.945213] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.954258] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.963303] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2cbe4000 sg_len=16384
[ 28.971568] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 28.979405] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 28.988450] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 28.997496] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.006550] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2c0ac000 sg_len=12288
[ 29.014900] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 29.022730] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.031775] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.040824] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec92d400, count: 11 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 21
[ 29.053956] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 29.063977] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 29.073219] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 29.081229] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 29.087073] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 29.098556] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 29.107262] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x3 lbah: 0x0
[ 29.115622] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 29.126236] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 29.134537] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 29.141855] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 29.150127] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 29.156837] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 29.189461] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=4
[ 29.198354] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=4 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 29.210093] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0af000 sg_len=4096
[ 29.218279] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.227331] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2cbb0000 sg_len=16384
[ 29.235604] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 29.243442] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.252487] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.261532] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.270578] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2cbe8000 sg_len=16384
[ 29.278851] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 29.286688] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.295733] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.304779] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.313825] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2cba4000 sg_len=4096
[ 29.322010] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.331058] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 4 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 8
[ 29.344017] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 29.354037] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 29.363300] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 29.371307] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 29.377142] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 29.388626] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 29.397332] sata-dwc 4bffd1000.sata: feature: 0x50 nsect: 0x0 lbal: 0x0 lbam: 0x5c lbah: 0x38
[ 29.405865] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 29.416213] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 29.424490] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 29.431803] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 29.440075] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 29.446785] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 29.455262] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 29.464150] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 29.475891] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cba5000 sg_len=4096
[ 29.484076] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.493133] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 29.506091] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 29.516111] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 29.525320] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 29.533329] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 29.539165] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 29.550647] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 29.559345] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x58 lbam: 0x5c lbah: 0x38
[ 29.567966] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 29.578172] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 29.586442] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 29.593755] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 29.602019] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 29.608729] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 29.617105] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 29.625989] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 29.637731] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cba6000 sg_len=8192
[ 29.645916] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.654964] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 29.667922] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 29.677942] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 29.687156] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 29.695170] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 29.701004] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 29.712488] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 29.721195] sata-dwc 4bffd1000.sata: feature: 0x10 nsect: 0x0 lbal: 0x68 lbam: 0x5c lbah: 0x38
[ 29.729815] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 29.740036] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 29.748308] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 29.755621] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 29.763893] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 29.770595] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 29.778623] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 29.787508] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 29.799250] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c9fc000 sg_len=16384
[ 29.807522] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.816575] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 29.825624] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 2
[ 29.838581] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 29.848592] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 29.857797] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 29.865803] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 29.871638] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 29.883121] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 29.891819] sata-dwc 4bffd1000.sata: feature: 0x20 nsect: 0x0 lbal: 0x80 lbam: 0x5c lbah: 0x38
[ 29.900440] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 29.910693] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 29.918968] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 29.926280] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 29.934544] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 29.941246] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 29.949762] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=6
[ 29.958647] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=6 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 29.970387] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca94000 sg_len=4096
[ 29.978573] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 29.987627] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2ca97000 sg_len=4096
[ 29.995812] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.004857] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c108000 sg_len=8192
[ 30.013034] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.022079] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2ca8c000 sg_len=8192
[ 30.030256] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.039302] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2ca2c000 sg_len=16384
[ 30.047574] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.056619] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.065664] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2ca30000 sg_len=4096
[ 30.073841] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.082889] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 6 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 7
[ 30.095848] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 30.105867] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 30.115086] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 30.123094] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 30.128931] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 30.140413] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 30.149120] sata-dwc 4bffd1000.sata: feature: 0x58 nsect: 0x0 lbal: 0xa8 lbam: 0x5c lbah: 0x38
[ 30.157740] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 30.168095] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 30.176377] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 30.183694] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 30.191967] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 30.198677] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 30.328473] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=3
[ 30.337364] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=3 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 30.349102] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca31000 sg_len=12288
[ 30.357376] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.366428] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.375473] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2cad0000 sg_len=16384
[ 30.383737] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.391575] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.400621] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.409666] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.418711] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2ca9c000 sg_len=12288
[ 30.426976] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.434813] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.443859] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.452907] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 3 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 7
[ 30.465866] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 30.475887] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 30.485142] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 30.493147] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 30.498983] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 30.510466] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 30.519172] sata-dwc 4bffd1000.sata: feature: 0x50 nsect: 0x0 lbal: 0x0 lbam: 0x5d lbah: 0x38
[ 30.527706] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 30.538081] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 30.546357] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 30.553669] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 30.561941] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 30.568651] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 30.577125] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=3
[ 30.586016] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=3 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 30.597757] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca9f000 sg_len=4096
[ 30.605943] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.614995] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2ca60000 sg_len=16384
[ 30.623260] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.631098] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.640144] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.649198] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.658251] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2caac000 sg_len=4096
[ 30.666436] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.675484] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 3 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 5
[ 30.688443] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 30.698463] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 30.707681] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 30.715690] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 30.721526] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 30.733008] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 30.741715] sata-dwc 4bffd1000.sata: feature: 0x30 nsect: 0x0 lbal: 0x58 lbam: 0x5d lbah: 0x38
[ 30.750327] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 30.760615] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 30.768890] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 30.776203] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 30.784475] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 30.791177] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 30.799221] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=5
[ 30.808107] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=5 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 30.819848] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2caad000 sg_len=12288
[ 30.828112] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 30.837157] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.846202] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c17a000 sg_len=8192
[ 30.854379] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.862209] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.871255] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.880308] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2ca5a000 sg_len=8192
[ 30.888485] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.896315] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.905360] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.914406] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c186000 sg_len=8192
[ 30.922583] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 30.930421] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.939466] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.948512] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c094000 sg_len=4096
[ 30.956697] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 30.965744] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 5 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 9
[ 30.978703] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 30.988723] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 30.997926] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 30.997933] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 30.997941] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 30.997948] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 30.997955] sata-dwc 4bffd1000.sata: feature: 0x50 nsect: 0x0 lbal: 0x90 lbam: 0x5d lbah: 0x38
[ 30.997963] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x3a hob_lbam: 0x0 hob_lbah: 0x0
[ 31.006022] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.006032] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.006038] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.006044] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.006052] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.006130] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.006140] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ef00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.006147] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c095000 sg_len=12288
[ 31.006153] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.006159] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.006168] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ef00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 2
[ 31.006176] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.006194] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
** 7 printk messages dropped ** [ 31.006376] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
** 589 printk messages dropped ** [ 31.392635] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2cb82000 sg_len=4096
** 320 printk messages dropped ** [ 31.452556] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
** 11 printk messages dropped ** [ 31.455443] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.455451] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.455458] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.455465] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.455870] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.455881] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.455889] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c3a6000 sg_len=4096
[ 31.455897] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.455907] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.455915] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.455935] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.456057] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.456064] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.456072] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.456079] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.456086] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x18 lbah: 0x40
[ 31.456093] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.456118] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.456128] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.456134] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.456141] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.456148] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.456398] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.456408] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.456415] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c3a7000 sg_len=4096
[ 31.456422] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.456431] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.456439] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.456458] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.456544] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.456551] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.456559] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.456566] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.456573] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x18 lbam: 0x10 lbah: 0x40
[ 31.456581] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.456624] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.456634] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.456641] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.456647] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.456654] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.457283] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.457294] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.457301] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ba96000 sg_len=4096
[ 31.457308] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.457318] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.457326] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.457346] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.457420] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.457426] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.457435] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.457442] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.457449] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x38 lbam: 0x10 lbah: 0x40
[ 31.457457] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.457484] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.457495] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.457502] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.457508] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.457515] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.457705] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.457714] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.457721] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ba97000 sg_len=4096
[ 31.457728] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.457738] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.457745] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.457764] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.457842] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.457848] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.457856] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.457863] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.457870] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x78 lbam: 0x10 lbah: 0x40
[ 31.457878] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.457989] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.458000] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.458006] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.458013] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.458020] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.458324] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.458334] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.458342] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c34a000 sg_len=4096
[ 31.458349] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.458358] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.458366] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.458384] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.458470] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.458476] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.458484] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.458491] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.458498] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x10 lbam: 0x10 lbah: 0x40
[ 31.458506] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.458530] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.458540] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.458546] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.458552] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.458559] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.458647] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=2
[ 31.458656] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=2 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.458663] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c34b000 sg_len=4096
[ 31.458669] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.458676] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c24a000 sg_len=8192
[ 31.458683] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.458689] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.458696] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.458705] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 2 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 3
[ 31.458712] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.458730] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.458810] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.458816] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.458824] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.458831] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.458838] sata-dwc 4bffd1000.sata: feature: 0x18 nsect: 0x0 lbal: 0x20 lbam: 0x10 lbah: 0x40
[ 31.458845] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.458907] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.458917] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.458924] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.458930] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.458937] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.459008] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=4
[ 31.459017] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=4 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.459024] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2ca5c000 sg_len=8192
[ 31.459031] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.459038] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2caa4000 sg_len=8192
[ 31.459044] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.459051] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c902000 sg_len=8192
[ 31.459057] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.459063] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2cb8c000 sg_len=4096
[ 31.459070] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459079] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 4 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 4
[ 31.459086] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.459104] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.459180] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.459186] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.459195] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.459202] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.459209] sata-dwc 4bffd1000.sata: feature: 0x38 nsect: 0x0 lbal: 0x40 lbam: 0x10 lbah: 0x40
[ 31.459216] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.459339] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.459352] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.459359] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.459365] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.459372] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.459481] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=10
[ 31.459491] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec929200 nelem=10 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.459497] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb8d000 sg_len=4096
[ 31.459505] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459511] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c168000 sg_len=8192
[ 31.459518] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459525] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459531] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459537] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b932000 sg_len=8192
[ 31.459544] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459550] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459556] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459563] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2ba7c000 sg_len=8192
[ 31.459570] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459576] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459582] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459589] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c10c000 sg_len=8192
[ 31.459595] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459602] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459608] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459615] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c1d4000 sg_len=8192
[ 31.459621] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459627] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459634] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459640] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c1b6000 sg_len=8192
[ 31.459647] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459653] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459659] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459666] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c12e000 sg_len=8192
[ 31.459673] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459679] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459685] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459692] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2cb8a000 sg_len=8192
[ 31.459699] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.459705] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459711] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459718] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2b972000 sg_len=4096
[ 31.459724] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.459733] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec929200, count: 10 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 18
[ 31.459741] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.459760] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.459838] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.459844] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.459853] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.459859] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.459867] sata-dwc 4bffd1000.sata: feature: 0x90 nsect: 0x0 lbal: 0x80 lbam: 0x10 lbah: 0x40
[ 31.459874] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.460196] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.460210] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.460216] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.460223] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.460230] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.460833] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=9
[ 31.460844] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec929200 nelem=9 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.460852] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b973000 sg_len=4096
[ 31.460859] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460867] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c324000 sg_len=16384
[ 31.460874] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.460880] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460887] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.460893] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460899] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c34c000 sg_len=16384
[ 31.460906] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.460912] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460919] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.460925] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460931] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c1dc000 sg_len=16384
[ 31.460938] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.460944] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460951] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.460957] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460964] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c1d0000 sg_len=16384
[ 31.460970] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.460977] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460983] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.460989] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.460995] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2cb84000 sg_len=16384
[ 31.461002] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.461008] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461015] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.461021] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461027] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c140000 sg_len=16384
[ 31.461034] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.461040] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461047] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.461053] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461060] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c1b8000 sg_len=16384
[ 31.461066] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.461073] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461079] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.461085] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461092] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2baf0000 sg_len=4096
[ 31.461098] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.461108] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec929200, count: 9 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 23
[ 31.461115] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.461135] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.461215] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.461222] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.461231] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.461238] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.461245] sata-dwc 4bffd1000.sata: feature: 0xf0 nsect: 0x0 lbal: 0x10 lbam: 0x11 lbah: 0x40
[ 31.461253] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.461724] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.461738] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.461745] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.461752] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.461760] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.462790] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=9
[ 31.462802] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec929200 nelem=9 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.462810] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2baf1000 sg_len=12288
[ 31.462818] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462824] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462831] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2bae4000 sg_len=16384
[ 31.462838] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.462844] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462851] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462857] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462864] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2bb30000 sg_len=16384
[ 31.462870] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.462877] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462883] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462889] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462896] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2b974000 sg_len=16384
[ 31.462902] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.462909] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462915] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462921] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462928] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c3a0000 sg_len=16384
[ 31.462935] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.462941] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462947] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462953] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462960] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2b934000 sg_len=16384
[ 31.462967] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.462973] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462979] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.462985] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.462992] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2c334000 sg_len=16384
[ 31.462999] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.463005] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.463011] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.463018] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.463024] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c314000 sg_len=16384
[ 31.463031] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.463037] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.463043] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.463050] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.463056] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2c0c8000 sg_len=4096
[ 31.463063] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.463072] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec929200, count: 9 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 24
[ 31.463081] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.463101] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.463194] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.463200] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.463209] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.463217] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.463224] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x12 lbah: 0x40
[ 31.463232] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.463740] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.463754] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.463762] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.463769] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.463777] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.464559] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=6
[ 31.464571] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=6 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.464578] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0c9000 sg_len=12288
[ 31.464585] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464592] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464599] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2b878000 sg_len=16384
[ 31.464606] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.464612] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464618] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464624] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464631] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b8b0000 sg_len=32768
[ 31.464638] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.464644] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464650] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464656] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464663] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464669] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464676] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2ba98000 sg_len=32768
[ 31.464682] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.464688] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464695] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464701] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464707] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464713] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464720] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c170000 sg_len=32768
[ 31.464727] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.464733] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464739] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464745] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464752] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.464758] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464765] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2b998000 sg_len=4096
[ 31.464771] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.464780] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 6 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 21
[ 31.464788] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.464808] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.464906] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.464912] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.464921] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.464928] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.464935] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x13 lbah: 0x40
[ 31.464943] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.465443] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.465455] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.465462] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.465469] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.465476] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.466483] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=6
[ 31.466495] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=6 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.466503] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b999000 sg_len=8192
[ 31.466511] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466518] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2b99c000 sg_len=16384
[ 31.466524] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466530] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466537] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b980000 sg_len=32768
[ 31.466543] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466549] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466556] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466562] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466568] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2b8c8000 sg_len=32768
[ 31.466575] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466581] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466587] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466594] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466600] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2b870000 sg_len=32768
[ 31.466606] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466613] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466619] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466625] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466632] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c3a8000 sg_len=8192
[ 31.466638] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.466648] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 6 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 16
[ 31.466656] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.466676] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.467801] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.469475] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.469483] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.469493] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.469500] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.469507] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x4 lbah: 0x40
[ 31.469515] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x10 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.469796] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.470296] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.470311] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.470319] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.470326] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.470334] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.471204] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=5
[ 31.471216] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=5 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.471224] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c3aa000 sg_len=24576
[ 31.471232] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471239] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471245] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471252] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c198000 sg_len=32768
[ 31.471259] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471265] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471271] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471277] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471284] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c338000 sg_len=32768
[ 31.471290] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471296] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471303] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471309] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471316] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c160000 sg_len=32768
[ 31.471322] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471328] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471334] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471341] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471347] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c0e0000 sg_len=8192
[ 31.471354] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.471364] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 5 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 16
[ 31.471372] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.471393] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.471470] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.471477] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.471486] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.471493] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.471501] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0x5 lbah: 0x40
[ 31.471509] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x10 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.472029] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.472043] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.472050] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.472057] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.472064] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.473338] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=5
[ 31.473352] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=5 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.473360] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0e2000 sg_len=24576
[ 31.473368] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473374] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473380] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473387] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c0c0000 sg_len=32768
[ 31.473393] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473400] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473406] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473413] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473420] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c0d0000 sg_len=32768
[ 31.473426] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473432] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473438] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473445] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473451] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c098000 sg_len=32768
[ 31.473458] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473464] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473470] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473476] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.473483] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c2c0000 sg_len=4096
[ 31.473489] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.473499] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 5 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 16
[ 31.473507] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.473528] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.473643] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.473650] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.473659] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.473666] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.473674] sata-dwc 4bffd1000.sata: feature: 0xf8 nsect: 0x0 lbal: 0x0 lbam: 0x6 lbah: 0x40
[ 31.473681] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x10 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.474185] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.474199] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.474207] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.474214] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.474222] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.475055] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=3
[ 31.475067] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6eb00 nelem=3 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.475075] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c2c1000 sg_len=28672
[ 31.475082] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475089] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475095] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475101] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475108] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2cb58000 sg_len=32768
[ 31.475115] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.475121] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475127] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475133] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475140] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475146] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475152] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2cb40000 sg_len=4096
[ 31.475159] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475168] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6eb00, count: 3 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 10
[ 31.475176] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.475197] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.475276] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.475282] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.475291] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.475298] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.475305] sata-dwc 4bffd1000.sata: feature: 0x80 nsect: 0x0 lbal: 0x0 lbam: 0x7 lbah: 0x40
[ 31.475313] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x10 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.475567] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.475579] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.475586] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.475593] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.475600] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.475734] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=2
[ 31.475743] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=2 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.475751] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2cb41000 sg_len=28672
[ 31.475758] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475764] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475770] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475776] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475783] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c0a0000 sg_len=24576
[ 31.475790] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.475796] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475802] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475809] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00002000 val: 0x00000800
[ 31.475815] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.475824] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 2 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 8
[ 31.475831] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.475850] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.475951] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.475958] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.475966] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.475973] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.475980] sata-dwc 4bffd1000.sata: feature: 0x68 nsect: 0x0 lbal: 0x88 lbam: 0x7 lbah: 0x40
[ 31.475988] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x10 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.476266] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.476277] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.476284] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.476290] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.476297] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.476906] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.476918] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.476925] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0a6000 sg_len=4096
[ 31.476932] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.476942] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.476950] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.476970] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.489852] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.492400] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.492407] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.492418] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.492425] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.492433] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x20 lbah: 0x40
[ 31.492440] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.492466] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.492477] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.492485] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.492492] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.492499] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.493289] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.493300] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.493308] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b93a000 sg_len=4096
[ 31.493316] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.493326] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.493334] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.493355] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.493445] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.493451] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.493460] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.493467] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.493474] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x0 lbah: 0x0
[ 31.493482] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.493506] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.493516] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.493523] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.493530] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.493537] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.493780] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.493790] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.493797] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b939000 sg_len=4096
[ 31.493804] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.493814] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.493821] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.493839] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.493938] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.493945] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.493953] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.493960] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.493967] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x18 lbam: 0x0 lbah: 0x0
[ 31.493974] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.494001] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.494011] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.494018] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.494024] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.494031] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.494180] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.494190] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6e800 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.494196] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b938000 sg_len=4096
[ 31.494203] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.494213] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6e800, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.494220] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.494238] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.494332] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.494339] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.494347] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.494354] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.494361] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x38 lbam: 0x0 lbah: 0x0
[ 31.494368] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.494393] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.494403] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.494410] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.494416] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.494423] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.498149] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.501805] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=17
[ 31.501818] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec8e2400 nelem=17 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.501825] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c0cf000 sg_len=4096
[ 31.501833] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501840] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2cb56000 sg_len=8192
[ 31.501847] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501853] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501859] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501866] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2cb18000 sg_len=8192
[ 31.501872] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501879] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501885] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501892] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c340000 sg_len=8192
[ 31.501898] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501904] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501911] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501917] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c116000 sg_len=8192
[ 31.501924] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501930] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501936] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501943] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2c180000 sg_len=8192
[ 31.501950] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501956] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501962] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501969] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2ca10000 sg_len=8192
[ 31.501975] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.501981] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501988] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.501994] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c9fa000 sg_len=8192
[ 31.502001] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502007] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502013] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502020] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2c092000 sg_len=8192
[ 31.502027] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502033] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502039] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502046] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2caaa000 sg_len=8192
[ 31.502052] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502059] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502065] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502071] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2cb16000 sg_len=8192
[ 31.502078] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502084] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502091] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502097] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2cad4000 sg_len=8192
[ 31.502104] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502110] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502116] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502123] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2ca90000 sg_len=8192
[ 31.502129] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502136] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502142] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502148] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=13 sg_addr=0x2c9d0000 sg_len=8192
[ 31.502155] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502161] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502168] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502174] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=14 sg_addr=0x2cba0000 sg_len=8192
[ 31.502181] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502187] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502193] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502200] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=15 sg_addr=0x2cb9e000 sg_len=8192
[ 31.502207] sata-dwc 4bffd1000.sata: SPLITTING: fis_len=4096(0x1000) len=8192(0x2000)
[ 31.502213] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502219] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502226] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=16 sg_addr=0x2c0aa000 sg_len=4096
[ 31.502232] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.502241] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec8e2400, count: 17 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 32
[ 31.502250] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.502271] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.507977] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.507985] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.507996] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.508003] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.508010] sata-dwc 4bffd1000.sata: feature: 0x00 nsect: 0x0 lbal: 0x0 lbam: 0xd lbah: 0x40
[ 31.508018] sata-dwc 4bffd1000.sata: hob_feature: 0x01 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.508803] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.508819] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.508826] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.508834] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.508841] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.511963] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=31
[ 31.511975] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec8e2400 nelem=31 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.511983] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c174000 sg_len=4096
[ 31.511991] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.511997] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2c173000 sg_len=4096
[ 31.512004] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512010] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2c172000 sg_len=4096
[ 31.512016] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512023] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2c171000 sg_len=4096
[ 31.512029] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512036] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2c170000 sg_len=4096
[ 31.512042] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512049] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2ba9f000 sg_len=4096
[ 31.512055] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512061] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2ba9e000 sg_len=4096
[ 31.512068] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512074] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2ba9d000 sg_len=4096
[ 31.512081] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512087] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2ba9c000 sg_len=4096
[ 31.512093] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512100] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2ba9b000 sg_len=4096
[ 31.512106] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512113] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2ba9a000 sg_len=4096
[ 31.512119] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512126] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2ba99000 sg_len=4096
[ 31.512132] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512139] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2b983000 sg_len=4096
[ 31.512145] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512151] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=13 sg_addr=0x2b982000 sg_len=4096
[ 31.512158] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512164] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=14 sg_addr=0x2b981000 sg_len=4096
[ 31.512171] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512177] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=15 sg_addr=0x2b980000 sg_len=4096
[ 31.512183] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512190] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=16 sg_addr=0x2b99f000 sg_len=4096
[ 31.512196] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512203] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=17 sg_addr=0x2b99e000 sg_len=4096
[ 31.512209] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512216] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=18 sg_addr=0x2b99d000 sg_len=4096
[ 31.512222] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512228] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=19 sg_addr=0x2b99c000 sg_len=4096
[ 31.512235] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512241] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=20 sg_addr=0x2b99a000 sg_len=4096
[ 31.512248] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512254] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=21 sg_addr=0x2b999000 sg_len=4096
[ 31.512260] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512267] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=22 sg_addr=0x2c0a6000 sg_len=4096
[ 31.512273] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512280] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=23 sg_addr=0x2c3a6000 sg_len=4096
[ 31.512286] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512293] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=24 sg_addr=0x2b998000 sg_len=4096
[ 31.512299] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512305] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=25 sg_addr=0x2c177000 sg_len=4096
[ 31.512312] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512318] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=26 sg_addr=0x2b871000 sg_len=4096
[ 31.512325] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512331] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=27 sg_addr=0x2b870000 sg_len=4096
[ 31.512337] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512344] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=28 sg_addr=0x2b8cf000 sg_len=4096
[ 31.512350] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512357] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=29 sg_addr=0x2b8ce000 sg_len=4096
[ 31.512363] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512370] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=30 sg_addr=0x2b8cd000 sg_len=4096
[ 31.512376] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.512385] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec8e2400, count: 31 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 31
[ 31.512394] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.512414] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.512516] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.512523] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.512533] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.512540] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.512548] sata-dwc 4bffd1000.sata: feature: 0xf8 nsect: 0x0 lbal: 0x0 lbam: 0xe lbah: 0x40
[ 31.512555] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.513154] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.513974] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.513992] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.514000] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.514007] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.514015] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.515366] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=16
[ 31.515378] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec929400 nelem=16 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.515386] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2b8cc000 sg_len=4096
[ 31.515394] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515401] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2b8cb000 sg_len=4096
[ 31.515407] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515413] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b8ca000 sg_len=4096
[ 31.515420] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515426] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2b8c9000 sg_len=4096
[ 31.515432] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515439] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2b8c8000 sg_len=4096
[ 31.515445] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515452] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2b987000 sg_len=4096
[ 31.515458] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515464] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2b986000 sg_len=4096
[ 31.515471] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515477] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2b985000 sg_len=4096
[ 31.515483] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515490] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2b984000 sg_len=4096
[ 31.515496] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515503] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2c3af000 sg_len=4096
[ 31.515509] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515516] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2c3ae000 sg_len=4096
[ 31.515522] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515529] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2c3ad000 sg_len=4096
[ 31.515535] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515541] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2c3ac000 sg_len=4096
[ 31.515548] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515554] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=13 sg_addr=0x2c3ab000 sg_len=4096
[ 31.515560] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515567] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=14 sg_addr=0x2c3aa000 sg_len=4096
[ 31.515573] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515580] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=15 sg_addr=0x2c3a9000 sg_len=4096
[ 31.515586] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.515596] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec929400, count: 16 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 16
[ 31.515604] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.515625] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.515706] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.515713] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.515723] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.515730] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.515737] sata-dwc 4bffd1000.sata: feature: 0x80 nsect: 0x0 lbal: 0x0 lbam: 0xf lbah: 0x40
[ 31.515745] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.515994] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.516012] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.516020] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.516027] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.516034] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.517784] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=13
[ 31.517796] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec929400 nelem=13 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.517804] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c3a8000 sg_len=4096
[ 31.517812] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517818] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=1 sg_addr=0x2b877000 sg_len=4096
[ 31.517825] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517831] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=2 sg_addr=0x2b876000 sg_len=4096
[ 31.517837] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517844] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=3 sg_addr=0x2b875000 sg_len=4096
[ 31.517850] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517857] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=4 sg_addr=0x2b874000 sg_len=4096
[ 31.517863] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517870] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=5 sg_addr=0x2b873000 sg_len=4096
[ 31.517876] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517882] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=6 sg_addr=0x2b872000 sg_len=4096
[ 31.517889] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517895] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=7 sg_addr=0x2c33d000 sg_len=4096
[ 31.517901] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517908] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=8 sg_addr=0x2c33c000 sg_len=4096
[ 31.517914] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517921] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=9 sg_addr=0x2c33b000 sg_len=4096
[ 31.517927] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517934] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=10 sg_addr=0x2c33a000 sg_len=4096
[ 31.517940] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517946] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=11 sg_addr=0x2c339000 sg_len=4096
[ 31.517953] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517959] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=12 sg_addr=0x2c338000 sg_len=4096
[ 31.517966] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.517975] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec929400, count: 13 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 13
[ 31.517983] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.518004] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.518092] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.518098] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.518107] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.518114] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.518121] sata-dwc 4bffd1000.sata: feature: 0x68 nsect: 0x0 lbal: 0x88 lbam: 0xf lbah: 0x40
[ 31.518129] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.518337] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.518350] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.518357] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.518364] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.518372] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.520274] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 31.520287] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=edd6ee00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 31.520295] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x2c19f000 sg_len=4096
[ 31.520303] sata-dwc 4bffd1000.sata: map_sg_to_lli setting ctl.high len: 0x00001000 val: 0x00000400
[ 31.520313] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xedd6ee00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 1
[ 31.520321] sata-dwc 4bffd1000.sata: sata_dwc_qc_issue: tag=0 ap->link.sactive = 0x00000001 sactive=0x00000001
[ 31.520342] sata-dwc 4bffd1000.sata: sata_dwc_exec_command_by_tag cmd(0x60): READ FPDMA QUEUED tag=0
[ 31.521708] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ 31.538754] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x00000082 active_tag=-84148995
[ 31.538761] sata-dwc 4bffd1000.sata: sata_dwc_isr: NEWFP tag=0
[ 31.538772] sata-dwc 4bffd1000.sata: sata_dwc_bmdma_start_by_tag qc=eca280b8 tag: 0 cmd: 0x60 dma_dir: from device start_dma? 1
[ 31.538779] sata-dwc 4bffd1000.sata: taskfile cmd: 0x60 protocol: ATA NCQ flags:0x17 device: 40
[ 31.538786] sata-dwc 4bffd1000.sata: feature: 0x08 nsect: 0x0 lbal: 0x0 lbam: 0x20 lbah: 0x0
[ 31.538794] sata-dwc 4bffd1000.sata: hob_feature: 0x00 hob_nsect: 0x0 hob_lbal: 0x0 hob_lbam: 0x0 hob_lbah: 0x0
[ 31.538827] sata-dwc 4bffd1000.sata: eot=0x00000001 err=0x00000000 pending=2 active port=0
[ 31.538838] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 31.538845] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA NCQ
[ 31.538852] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 31.538860] sata-dwc 4bffd1000.sata: QC complete cmd=0x60 status=0x00 ata3: protocol=4
[ 31.546017] systemd-journald[132]: /dev/kmsg buffer overrun, some messages lost.
[ OK ] Started LSB: start Samba SMB/CIFS daemon (smbd).

[ OK ] Started Wait for all "auto" /etc/ne...be up for network-online.target.
[ OK ] Started LSB: Raise network interfaces..
[ OK ] Reached target System Initialization.
[ OK ] Started CUPS Scheduler.
[ OK ] Listening on CUPS Scheduler.
Starting Restore Sound Card State...
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
Starting Console System Startup Logging...
[ OK ] Started Trigger resolvconf update for networkd DNS.
[ OK ] Reached target Paths.
[ OK ] Listening on UUID daemon activation socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Modem Manager...
[ OK ] Started Cgroup management daemon.
Starting LSB: start and stop timidity...
Starting LSB: daemon to balance interrupts for SMP systems...
[ OK ] Started Run anacron jobs.
Starting Restore /etc/resolv.conf i...e the ppp link was shut down....
Starting LSB: handle special hotkeys of Apple computers...
Starting Avahi mDNS/DNS-SD Stack...
Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
[ 45.250230] cgroup: new mount options do not match the existing superblock, will be ignored
[ OK ] Started Regular background program processing daemon.
Starting Permit User Sessions...
[ OK ] Started crash report submission daemon.
Starting LSB: Load kernel modules needed to enable cpufreq scaling...
Starting Network Manager...
Starting Accounts Service...
Starting Login Service...
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Network Manager.
Starting Initialize hardware monitoring sensors...
Starting LSB: automatic crash report generation...
Starting System Logging Service...
[ OK ] Started CUPS Scheduler.
[ OK ] Started Make remote CUPS printers available locally.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
Starting LSB: start Samba daemons for the AD DC...
Starting LSB: Start xrdp and sesman daemons...
Starting LSB: Tool to automatically...ubmit kernel crash signatures...
Starting LSB: start Samba NetBIOS nameserver (nmbd)...
Starting LSB: disk temperature monitoring daemon...
Starting LSB: Start NTP daemon...
Starting /etc/rc.local Compatibility...
[ OK ] Started Restore Sound Card State.
[ OK ] Started Console System Startup Logging.
[ OK ] Started LSB: start and stop timidity.
[ OK ] Started LSB: daemon to balance interrupts for SMP systems.
[ OK ] Started Restore /etc/resolv.conf if...ore the ppp link was shut down..
[ OK ] Started LSB: handle special hotkeys of Apple computers.
[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[ OK ] Started Permit User Sessions.
[ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
[ OK ] Started LSB: disk temperature monitoring daemon.
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started Initialize hardware monitoring sensors.
[ OK ] Started System Logging Service.
[ OK ] Started LSB: automatic crash report generation.
[ OK ] Started LSB: Start NTP daemon.
[ OK ] Started LSB: Tool to automatically ... submit kernel crash signatures.
[ OK ] Started LSB: Start xrdp and sesman daemons.
[ OK ] Started Login Service.
Starting Manage, Install and Generate Color Profiles...
Starting Authenticate and Authorize Users to Run Privileged Tasks...
Starting LSB: set CPUFreq kernel parameters...
Starting Light Display Manager...
[ 51.067073] IPv6: ADDRCONF(NETDEV_UP): tunl0: link is not ready
Starting Hold until boot process finishes up...
[ 51.280261] IPv6: ADDRCONF(NETDEV_UP): sit0: link is not ready
[ OK ] Started Hold until boot process finishes up.
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ 51.538467] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks.
[ OK ] Started Accounts Service.
[ OK ] Started Manage, Install and Generate Color Profiles.
Starting WPA supplicant...
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ OK ] Started Light Display Manager.
[ OK ] Started Modem Manager.
[ OK ] Started WPA supplicant.
Starting Network Manager Script Dispatcher Service...
[ OK ] Started Network Manager Script Dispatcher Service.

Ubuntu Xenial Xerus (development branch) Sam460ex ttyS0

Sam460ex login: [ 90.676144] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 90.685037] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ec10cb00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 90.696774] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 90.704087] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xec10cb00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 90.717887] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 90.725204] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA PIO
[ 91.295855] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=none n_elem=0
[ 91.304143] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg= (null) nelem=0 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 91.315883] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0x (null), count: 0 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 91.328944] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 91.336254] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA no data
[ 91.344873] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 91.351575] sata-dwc 4bffd1000.sata: QC complete cmd=0xe5 status=0x00 ata3: protocol=1
[ 91.489610] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 91.498508] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ecbecf00 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 91.510246] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 91.517559] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xecbecf00, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 91.531352] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 91.538671] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA PIO
[ 91.618710] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 91.627606] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ecbec400 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 91.639344] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 91.646665] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xecbec400, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 91.664382] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 91.671709] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA PIO
[ 91.820505] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=from device n_elem=1
[ 91.829402] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg=ecbec400 nelem=1 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 91.841140] sata-dwc 4bffd1000.sata: map_sg_to_lli: elem=0 sg_addr=0x0 sg_len=0
[ 91.848452] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0xecbec400, count: 1 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 91.865801] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 91.873132] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA PIO
[ 92.013482] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: port=0 dma dir=none n_elem=0
[ 92.021773] sata-dwc 4bffd1000.sata: map_sg_to_lli: sg= (null) nelem=0 lli=ffa0c000 dma_lli=0x0x000000002ca9a000 dmadr=0xf6a1e400
[ 92.033513] sata-dwc 4bffd1000.sata: dma_dwc_xfer_setup sg: 0x (null), count: 0 lli: ffa0c000 dma_lli: 0x2ca9a000lx addr: f6a1e400 lli count: 0
[ 92.130858] sata-dwc 4bffd1000.sata: sata_dwc_isr intpr=0x80000080 active_tag=0
[ 92.138186] sata-dwc 4bffd1000.sata: sata_dwc_isr non-NCQ cmd interrupt, protocol: ATA no data
[ 92.146800] sata-dwc 4bffd1000.sata: sata_dwc_qc_complete checkstatus? 1
[ 92.153503] sata-dwc 4bffd1000.sata: QC complete cmd=0xb0 status=0x00 ata3: protocol=1

Next message: Daniel Cashman: "[PATCH v7 1/4] mm: mmap: Add new /proc tunable for mmap_base ASLR."
Previous message: Andy Shevchenko: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
In reply to: Julian Margetson: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
Next in thread: Andy Shevchenko: "Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]