Re: [PATCH v2 13/19] ARM: dts: Add bus nodes using VDD_MIF for Exynos4x12

[Chanwoo Choi]

On 2015ë 12ì 10ì 12:17, Krzysztof Kozlowski wrote:
> On 09.12.2015 13:08, Chanwoo Choi wrote:
>> This patch adds the bus noes using VDD_MIF for Exynos4x12 SoC.
> 
> s/noes/nodes/

OK.

> 
>> Exynos4x12 has the following AXI buses to translate data
>> between DRAM and DMC/ACP/C2C.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> ---
>>  arch/arm/boot/dts/exynos4x12.dtsi | 72 +++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 72 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
>> index b77dac61ffb5..3bcf0939755e 100644
>> --- a/arch/arm/boot/dts/exynos4x12.dtsi
>> +++ b/arch/arm/boot/dts/exynos4x12.dtsi
>> @@ -282,6 +282,78 @@
>>  		clocks = <&clock CLK_SMMU_LITE1>, <&clock CLK_FIMC_LITE1>;
>>  		#iommu-cells = <0>;
>>  	};
>> +
>> +	bus_dmc: bus_dmc {
>> +		compatible = "samsung,exynos-bus";
>> +		clocks = <&clock CLK_DIV_DMC>;
>> +		clock-names = "bus";
>> +		operating-points-v2 = <&bus_dmc_opp_table>;
>> +		status = "disabled";
>> +	};
>> +
>> +	bus_acp: bus_acp {
>> +		compatible = "samsung,exynos-bus";
>> +		clocks = <&clock CLK_DIV_ACP>;
>> +		clock-names = "bus";
>> +		operating-points-v2 = <&bus_acp_opp_table>;
>> +		status = "disabled";
>> +	};
>> +
>> +	bus_c2c: bus_c2c {
>> +		compatible = "samsung,exynos-bus";
>> +		clocks = <&clock CLK_DIV_C2C>;
>> +		clock-names = "bus";
>> +		operating-points-v2 = <&bus_dmc_opp_table>;
>> +		status = "disabled";
>> +	};
>> +
>> +	bus_dmc_opp_table: opp_table1 {
>> +		compatible = "operating-points-v2";
>> +		opp-shared;
>> +
>> +		opp00 {
>> +			opp-hz = /bits/ 64 <100000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp01 {
>> +			opp-hz = /bits/ 64 <134000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp02 {
>> +			opp-hz = /bits/ 64 <160000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp03 {
>> +			opp-hz = /bits/ 64 <200000000>;
>> +			opp-microvolt = <950000>;
> 
> The exyno4_bus.c (from mainline) uses 267 MHz here. Why choosing 200 MHz?

There is no special reason.
I'll change it (200MHz -> 267MHz).

Best Regards,
Chanwoo Choi

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/