Re: [PATCHv6 4/5] devicetree: Add new ANX7814 SlimPort transmitter binding.

[Rob Herring]

On Fri, Dec 04, 2015 at 09:35:06AM +0100, Enric Balletbo i Serra wrote:
> The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> designed for portable devices.
> 
> You can add support to your board with current binding.
> 
> Example:
> 
> 	anx7814: anx7814@38 {
> 		compatible = "analogix,anx7814";
> 		reg = <0x38>;
> 		interrupt-parent = <&gpio0>
> 		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> 		pd-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> 		reset-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
> 		v10-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> 		ports {

This and the example below should be just "port" I think. Otherwise:

Acked-by: Rob Herring <robh@xxxxxxxxxx>


> 			anx7814_in: endpoint {
> 				remote-endpoint = <&hdmi0_out>;
> 			};
> 		};
> 	};
> 
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
> ---
> 
> Changes since last version (requested by Rob Herring)
> - Specify how many ports and how many endpoints for each port
> - Simplify to just port (dropping ports)
> - For cable det use an interrupt instead (to a gpio controller)
> 
>  .../devicetree/bindings/video/bridge/anx7814.txt   | 39 ++++++++++++++++++++++
>  1 file changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/video/bridge/anx7814.txt
> 
> diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/video/bridge/anx7814.txt
> new file mode 100644
> index 0000000..4e68789
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/bridge/anx7814.txt
> @@ -0,0 +1,39 @@
> +Analogix ANX7814 SlimPort (Full-HD Transmitter)
> +-----------------------------------------------
> +
> +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> +designed for portable devices.
> +
> +Required properties:
> +
> + - compatible		: "analogix,anx7814"
> + - reg			: I2C address of the device
> + - interrupt-parent	: Should be the phandle of the interrupt controller
> +			  that services interrupts for this device
> + - interrupts		: Should contain the cable detection interrupt
> + - pd-gpios		: Which GPIO to use for power down
> + - reset-gpios		: Which GPIO to use for reset
> +
> +Optional properties:
> +
> + - v10-gpios		: Which GPIO to use for V10 control.
> + - Video port for HDMI output, using the DT bindings defined in [1].
> +
> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example:
> +
> +	anx7814: anx7814@38 {
> +		compatible = "analogix,anx7814";
> +		reg = <0x38>;
> +		interrupt-parent = <&gpio0>
> +		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> +		pd-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> +		reset-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
> +		v10-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> +		ports {
> +			anx7814_in: endpoint {
> +				remote-endpoint = <&hdmi0_out>;
> +			};
> +		};
> +	};
> -- 
> 2.1.0
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/