[PATCH 11/12] cpufreq: arm-big-little: clarify frequency units

From: Ben Gamari
Date: Wed Dec 02 2015 - 16:32:33 EST


The frequency units are very confusing in this area as OPPs use Hz
whereas cpufreq uses kHz. Be explicit about this in variable naming.

Cc: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
Signed-off-by: Ben Gamari <ben@xxxxxxxxxxxxxxxx>
---
drivers/cpufreq/arm_big_little.c | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/cpufreq/arm_big_little.c b/drivers/cpufreq/arm_big_little.c
index 855599b..2d5761c 100644
--- a/drivers/cpufreq/arm_big_little.c
+++ b/drivers/cpufreq/arm_big_little.c
@@ -130,14 +130,14 @@ static unsigned int bL_cpufreq_get_rate(unsigned int cpu)
}

static int
-bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate)
+bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate_kHz)
{
unsigned long volt = 0, volt_old = 0;
long freq_Hz;
u32 old_rate;
int ret;

- freq_Hz = new_rate * 1000;
+ freq_Hz = new_rate_kHz * 1000;
old_rate = clk_get_rate(clk[cluster]) / 1000;

if (!IS_ERR(reg[cluster])) {
@@ -163,10 +163,10 @@ bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate)
pr_debug("%s: cpu %d, cluster: %d, %u MHz, %ld mV --> %u MHz, %ld mV\n",
__func__, cpu, cluster,
old_rate / 1000, (volt_old > 0) ? volt_old / 1000 : -1,
- new_rate / 1000, volt ? volt / 1000 : -1);
+ new_rate_kHz / 1000, volt ? volt / 1000 : -1);

/* scaling up? scale voltage before frequency */
- if (!IS_ERR(reg[cluster]) && new_rate > old_rate) {
+ if (!IS_ERR(reg[cluster]) && new_rate_kHz > old_rate) {
ret = regulator_set_voltage_tol(reg[cluster], volt, 0);
if (ret) {
pr_err("%s: cpu: %d, cluster: %d, failed to scale voltage up: %d\n",
@@ -175,7 +175,7 @@ bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate)
}
}

- ret = clk_set_rate(clk[cluster], new_rate * 1000);
+ ret = clk_set_rate(clk[cluster], new_rate_kHz * 1000);
if (WARN_ON(ret)) {
pr_err("%s: clk_set_rate failed: %d, cluster: %d\n",
__func__, cluster, ret);
@@ -185,7 +185,7 @@ bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate)
}

/* scaling down? scale voltage after frequency */
- if (!IS_ERR(reg[cluster]) && new_rate < old_rate) {
+ if (!IS_ERR(reg[cluster]) && new_rate_kHz < old_rate) {
ret = regulator_set_voltage_tol(reg[cluster], volt, 0);
if (ret) {
pr_err("%s: cpu: %d, cluster: %d, failed to scale voltage down: %d\n",
@@ -199,7 +199,7 @@ bL_cpufreq_set_rate_cluster(u32 cpu, u32 cluster, u32 new_rate)
}

static unsigned int
-bL_cpufreq_set_rate(u32 cpu, u32 old_cluster, u32 new_cluster, u32 rate)
+bL_cpufreq_set_rate(u32 cpu, u32 old_cluster, u32 new_cluster, u32 rate_kHz)
{
u32 new_rate, prev_rate;
int ret;
@@ -209,13 +209,13 @@ bL_cpufreq_set_rate(u32 cpu, u32 old_cluster, u32 new_cluster, u32 rate)

if (bLs) {
prev_rate = per_cpu(cpu_last_req_freq, cpu);
- per_cpu(cpu_last_req_freq, cpu) = rate;
+ per_cpu(cpu_last_req_freq, cpu) = rate_kHz;
per_cpu(physical_cluster, cpu) = new_cluster;

new_rate = find_cluster_maxfreq(new_cluster);
new_rate = ACTUAL_FREQ(new_cluster, new_rate);
} else {
- new_rate = rate;
+ new_rate = rate_kHz;
}

pr_debug("%s: cpu: %d, old cluster: %d, new cluster: %d, freq: %d\n",
@@ -236,7 +236,7 @@ bL_cpufreq_set_rate(u32 cpu, u32 old_cluster, u32 new_cluster, u32 rate)
} else if (ret && bLs) {
per_cpu(cpu_last_req_freq, cpu) = prev_rate;
per_cpu(physical_cluster, cpu) = old_cluster;
- }
+ }

mutex_unlock(&cluster_lock[new_cluster]);

--
2.6.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/