Re: [PATCH-v5 RESEND 3/5] i2c: pxa: Add support for pxa910/988 & new configuration features

[Vaibhav Hiremath]

On Saturday 12 September 2015 12:36 AM, Wolfram Sang wrote:
> On Mon, Aug 24, 2015 at 11:29:36AM +0530, Vaibhav Hiremath wrote:
> > TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
> > of standard & fast mode in pxa910/988; so this patch adds these two new
> > entries to "struct pxa_reg_layout" and "struct pxa_i2c".
> >
> > As discussed in the previous patch-series, the idea here is to add standard
> > DT properties for ilcr and iwcr configuration fields.
> > In case of Master ilcr is used for low/high time and in case of slave mode
> > of operation iwcr is used for setup/hold time.
>
> I need to rethink how to describe i2c bus timing parameters in DT in the
> next days. But this is planned for 4.4., promised.
>
> One thing I already wonder about this one...
>
> >   static const struct platform_device_id i2c_pxa_id_table[] = {
> >   	{ "pxa2xx-i2c",		REGS_PXA2XX },
> >   	{ "pxa3xx-pwri2c",	REGS_PXA3XX },
> >   	{ "ce4100-i2c",		REGS_CE4100 },
> > +	{ "pxa910-i2c",		REGS_PXA910 },
> >   	{ },
>
> You add a new platform_id...
>
> > @@ -1135,7 +1170,7 @@ static const struct i2c_algorithm i2c_pxa_pio_algorithm = {
> >   static const struct of_device_id i2c_pxa_dt_ids[] = {
> >   	{ .compatible = "mrvl,pxa-i2c", .data = (void *)REGS_PXA2XX },
> >   	{ .compatible = "mrvl,pwri2c", .data = (void *)REGS_PXA3XX },
> > -	{ .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA2XX },
> > +	{ .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA910 },
> >   	{}
>
> ...but change the compatible binding instead of adding a new one?

Yes, because the offset for both REGS_PXA2XX and REGS_PXA910 are same,
and for REGS_PXA2XX we already have compatible entry "mrvl,pxa-i2c".
And the i2c binding documentation, which says,
for platforms using REGS_PXA2XX, they need to provide additional node
"mrvl,pxa-i2c". Which is confusing :)

Also, when I did git-blame on the driver file to see why "mmp-twsi"
entry has been added without anyone really using it. But I did not find
anything meaningful.
So, from the code it was very clear that, "mmp-twsi" and "pxa-i2c" both
are same, its the code which I am adding here brings difference between 
them.

I tried to find datasheet for the platforms using "mmp-twsi", but was
unlucky.


Thanks,
Vaibhav




Thanks,
Vaibhav
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/