Re: [PATCH v3 2/3] ARM: at91/dt: add basic dtsi for sama5d2 SoC

From: Nicolas Ferre
Date: Thu Jul 30 2015 - 08:26:13 EST

Next message: Michal Hocko: "Re: Re: [V2 PATCH 1/3] x86/panic: Fix re-entrance problem due to panic on NMI"
Previous message: Stephen Rothwell: "Re: linux-next: build failure after merge of the block tree"
In reply to: Nicolas Ferre: "[PATCH v3 2/3] ARM: at91/dt: add basic dtsi for sama5d2 SoC"
Next in thread: Nicolas Ferre: "[PATCH v3 3/3] ARM: at91/dt: add minimal sama5d2 Xplained board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Le 30/07/2015 13:55, Nicolas Ferre a écrit :
> From: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
>
> Only the basic support for this new Atmel Cortex-A5 SoC. A subset of the
> peripherals is setup to allow booting.
> IRQ, clocks, USB, crypto, timers, rtc, ethernet, spi/i2c and
> uart/usart peripheral nodes are added.
>
> Signed-off-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
> ---
>
> Changes in v3:
> - remove sd/mmc nodes
> - remove generated clock nodes

Oh I forgot about this:
- corrected the DMA HW handler interfaces for SHA and AES thanks to Leilei!

Bye,

>
> Changes in v2:
> - fix sdmmc clocks and memory range
> - add flexcom and audio Class D amplifier peripheral clock definitions
> - add qspi peripheral clock definitions
> - add more generated clock definitions
> - fix DMA definitions for crypto peripherals
> - add spi, i2c and rtc nodes
>
> arch/arm/boot/dts/sama5d2.dtsi | 925 +++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 925 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d2.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
> new file mode 100644
> index 000000000000..f39258fa3815
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d2.dtsi
> @@ -0,0 +1,925 @@
> +/*
> + * sama5d2.dtsi - Device Tree Include file for SAMA5D2 family SoC
> + *
> + * Copyright (C) 2015 Atmel,
> + * 2015 Ludovic Desroches <ludovic.desroches@xxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +#include <dt-bindings/dma/at91.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/clock/at91.h>
> +
> +/ {
> + model = "Atmel SAMA5D2 family SoC";
> + compatible = "atmel,sama5d2";
> + interrupt-parent = <&aic>;
> +
> + aliases {
> + serial0 = &uart1;
> + serial1 = &uart3;
> + tcb0 = &tcb0;
> + tcb1 = &tcb1;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a5";
> + reg = <0>;
> + next-level-cache = <&L2>;
> + };
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal: slow_xtal {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <0>;
> + };
> +
> + main_xtal: main_xtal {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <0>;
> + };
> +
> + adc_op_clk: adc_op_clk{
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <1000000>;
> + };
> + };
> +
> + ns_sram: sram@00200000 {
> + compatible = "mmio-sram";
> + reg = <0x00200000 0x20000>;
> + };
> +
> + ahb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + usb0: gadget@00300000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "atmel,sama5d3-udc";
> + reg = <0x00300000 0x100000
> + 0xfc02c000 0x400>;
> + interrupts = <42 IRQ_TYPE_LEVEL_HIGH 2>;
> + clocks = <&udphs_clk>, <&utmi>;
> + clock-names = "pclk", "hclk";
> + status = "disabled";
> +
> + ep0 {
> + reg = <0>;
> + atmel,fifo-size = <64>;
> + atmel,nb-banks = <1>;
> + };
> +
> + ep1 {
> + reg = <1>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <3>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep2 {
> + reg = <2>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <3>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep3 {
> + reg = <3>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep4 {
> + reg = <4>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep5 {
> + reg = <5>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep6 {
> + reg = <6>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep7 {
> + reg = <7>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-dma;
> + atmel,can-isoc;
> + };
> +
> + ep8 {
> + reg = <8>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep9 {
> + reg = <9>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep10 {
> + reg = <10>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep11 {
> + reg = <11>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep12 {
> + reg = <12>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep13 {
> + reg = <13>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep14 {
> + reg = <14>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> +
> + ep15 {
> + reg = <15>;
> + atmel,fifo-size = <1024>;
> + atmel,nb-banks = <2>;
> + atmel,can-isoc;
> + };
> + };
> +
> + usb1: ohci@00400000 {
> + compatible = "atmel,at91rm9200-ohci", "usb-ohci";
> + reg = <0x00400000 0x100000>;
> + interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>;
> + clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
> + clock-names = "ohci_clk", "hclk", "uhpck";
> + status = "disabled";
> + };
> +
> + usb2: ehci@00500000 {
> + compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
> + reg = <0x00500000 0x100000>;
> + interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>;
> + clocks = <&utmi>, <&uhphs_clk>;
> + clock-names = "usb_clk", "ehci_clk";
> + status = "disabled";
> + };
> +
> + L2: cache-controller@00a00000 {
> + compatible = "arm,pl310-cache";
> + reg = <0x00a00000 0x1000>;
> + interrupts = <63 IRQ_TYPE_LEVEL_HIGH 4>;
> + cache-unified;
> + cache-level = <2>;
> + };
> +
> + apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + ramc0: ramc@f000c000 {
> + compatible = "atmel,sama5d3-ddramc";
> + reg = <0xf000c000 0x200>;
> + clocks = <&ddrck>, <&mpddr_clk>;
> + clock-names = "ddrck", "mpddr";
> + };
> +
> + dma0: dma-controller@f0010000 {
> + compatible = "atmel,sama5d4-dma";
> + reg = <0xf0010000 0x1000>;
> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
> + #dma-cells = <1>;
> + clocks = <&dma0_clk>;
> + clock-names = "dma_clk";
> + };
> +
> + pmc: pmc@f0014000 {
> + compatible = "atmel,sama5d2-pmc";
> + reg = <0xf0014000 0x160>;
> + interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
> + interrupt-controller;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #interrupt-cells = <1>;
> +
> + main_rc_osc: main_rc_osc {
> + compatible = "atmel,at91sam9x5-clk-main-rc-osc";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_MOSCRCS>;
> + clock-frequency = <12000000>;
> + clock-accuracy = <100000000>;
> + };
> +
> + main_osc: main_osc {
> + compatible = "atmel,at91rm9200-clk-main-osc";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_MOSCS>;
> + clocks = <&main_xtal>;
> + };
> +
> + main: mainck {
> + compatible = "atmel,at91sam9x5-clk-main";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_MOSCSELS>;
> + clocks = <&main_rc_osc &main_osc>;
> + };
> +
> + plla: pllack {
> + compatible = "atmel,sama5d3-clk-pll";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_LOCKA>;
> + clocks = <&main>;
> + reg = <0>;
> + atmel,clk-input-range = <12000000 12000000>;
> + #atmel,pll-clk-output-range-cells = <4>;
> + atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>;
> + };
> +
> + plladiv: plladivck {
> + compatible = "atmel,at91sam9x5-clk-plldiv";
> + #clock-cells = <0>;
> + clocks = <&plla>;
> + };
> +
> + utmi: utmick {
> + compatible = "atmel,at91sam9x5-clk-utmi";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_LOCKU>;
> + clocks = <&main>;
> + };
> +
> + mck: masterck {
> + compatible = "atmel,at91sam9x5-clk-master";
> + #clock-cells = <0>;
> + interrupt-parent = <&pmc>;
> + interrupts = <AT91_PMC_MCKRDY>;
> + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
> + atmel,clk-output-range = <124000000 166000000>;
> + atmel,clk-divisors = <1 2 4 3>;
> + };
> +
> + h32ck: h32mxck {
> + #clock-cells = <0>;
> + compatible = "atmel,sama5d4-clk-h32mx";
> + clocks = <&mck>;
> + };
> +
> + usb: usbck {
> + compatible = "atmel,at91sam9x5-clk-usb";
> + #clock-cells = <0>;
> + clocks = <&plladiv>, <&utmi>;
> + };
> +
> + prog: progck {
> + compatible = "atmel,at91sam9x5-clk-programmable";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupt-parent = <&pmc>;
> + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
> +
> + prog0: prog0 {
> + #clock-cells = <0>;
> + reg = <0>;
> + interrupts = <AT91_PMC_PCKRDY(0)>;
> + };
> +
> + prog1: prog1 {
> + #clock-cells = <0>;
> + reg = <1>;
> + interrupts = <AT91_PMC_PCKRDY(1)>;
> + };
> +
> + prog2: prog2 {
> + #clock-cells = <0>;
> + reg = <2>;
> + interrupts = <AT91_PMC_PCKRDY(2)>;
> + };
> + };
> +
> + systemck {
> + compatible = "atmel,at91rm9200-clk-system";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ddrck: ddrck {
> + #clock-cells = <0>;
> + reg = <2>;
> + clocks = <&mck>;
> + };
> +
> + lcdck: lcdck {
> + #clock-cells = <0>;
> + reg = <3>;
> + clocks = <&mck>;
> + };
> +
> + uhpck: uhpck {
> + #clock-cells = <0>;
> + reg = <6>;
> + clocks = <&usb>;
> + };
> +
> + udpck: udpck {
> + #clock-cells = <0>;
> + reg = <7>;
> + clocks = <&usb>;
> + };
> +
> + pck0: pck0 {
> + #clock-cells = <0>;
> + reg = <8>;
> + clocks = <&prog0>;
> + };
> +
> + pck1: pck1 {
> + #clock-cells = <0>;
> + reg = <9>;
> + clocks = <&prog1>;
> + };
> +
> + pck2: pck2 {
> + #clock-cells = <0>;
> + reg = <10>;
> + clocks = <&prog2>;
> + };
> +
> + iscck: iscck {
> + #clock-cells = <0>;
> + reg = <18>;
> + clocks = <&mck>;
> + };
> + };
> +
> + periph32ck {
> + compatible = "atmel,at91sam9x5-clk-peripheral";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&h32ck>;
> +
> + macb0_clk: macb0_clk {
> + #clock-cells = <0>;
> + reg = <5>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + tdes_clk: tdes_clk {
> + #clock-cells = <0>;
> + reg = <11>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + matrix1_clk: matrix1_clk {
> + #clock-cells = <0>;
> + reg = <14>;
> + };
> +
> + hsmc_clk: hsmc_clk {
> + #clock-cells = <0>;
> + reg = <17>;
> + };
> +
> + pioA_clk: pioA_clk {
> + #clock-cells = <0>;
> + reg = <18>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + flx0_clk: flx0_clk {
> + #clock-cells = <0>;
> + reg = <19>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + flx1_clk: flx1_clk {
> + #clock-cells = <0>;
> + reg = <20>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + flx2_clk: flx2_clk {
> + #clock-cells = <0>;
> + reg = <21>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + flx3_clk: flx3_clk {
> + #clock-cells = <0>;
> + reg = <22>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + flx4_clk: flx4_clk {
> + #clock-cells = <0>;
> + reg = <23>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uart0_clk: uart0_clk {
> + #clock-cells = <0>;
> + reg = <24>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uart1_clk: uart1_clk {
> + #clock-cells = <0>;
> + reg = <25>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uart2_clk: uart2_clk {
> + #clock-cells = <0>;
> + reg = <26>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uart3_clk: uart3_clk {
> + #clock-cells = <0>;
> + reg = <27>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uart4_clk: uart4_clk {
> + #clock-cells = <0>;
> + reg = <28>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + twi0_clk: twi0_clk {
> + reg = <29>;
> + #clock-cells = <0>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + twi1_clk: twi1_clk {
> + #clock-cells = <0>;
> + reg = <30>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + spi0_clk: spi0_clk {
> + #clock-cells = <0>;
> + reg = <33>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + spi1_clk: spi1_clk {
> + #clock-cells = <0>;
> + reg = <34>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + tcb0_clk: tcb0_clk {
> + #clock-cells = <0>;
> + reg = <35>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + tcb1_clk: tcb1_clk {
> + #clock-cells = <0>;
> + reg = <36>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + pwm_clk: pwm_clk {
> + #clock-cells = <0>;
> + reg = <38>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + adc_clk: adc_clk {
> + #clock-cells = <0>;
> + reg = <40>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + uhphs_clk: uhphs_clk {
> + #clock-cells = <0>;
> + reg = <41>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + udphs_clk: udphs_clk {
> + #clock-cells = <0>;
> + reg = <42>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + ssc0_clk: ssc0_clk {
> + #clock-cells = <0>;
> + reg = <43>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + ssc1_clk: ssc1_clk {
> + #clock-cells = <0>;
> + reg = <44>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + trng_clk: trng_clk {
> + #clock-cells = <0>;
> + reg = <47>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> +
> + classd_clk: classd_clk {
> + #clock-cells = <0>;
> + reg = <59>;
> + atmel,clk-output-range = <0 83000000>;
> + };
> + };
> +
> + periph64ck {
> + compatible = "atmel,at91sam9x5-clk-peripheral";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&mck>;
> +
> + dma0_clk: dma0_clk {
> + #clock-cells = <0>;
> + reg = <6>;
> + };
> +
> + dma1_clk: dma1_clk {
> + #clock-cells = <0>;
> + reg = <7>;
> + };
> +
> + aes_clk: aes_clk {
> + #clock-cells = <0>;
> + reg = <9>;
> + };
> +
> + aesb_clk: aesb_clk {
> + #clock-cells = <0>;
> + reg = <10>;
> + };
> +
> + sha_clk: sha_clk {
> + #clock-cells = <0>;
> + reg = <12>;
> + };
> +
> + mpddr_clk: mpddr_clk {
> + #clock-cells = <0>;
> + reg = <13>;
> + };
> +
> + matrix0_clk: matrix0_clk {
> + #clock-cells = <0>;
> + reg = <15>;
> + };
> +
> + sdmmc0_hclk: sdmmc0_hclk {
> + #clock-cells = <0>;
> + reg = <31>;
> + };
> +
> + sdmmc1_hclk: sdmmc1_hclk {
> + #clock-cells = <0>;
> + reg = <32>;
> + };
> +
> + lcdc_clk: lcdc_clk {
> + #clock-cells = <0>;
> + reg = <45>;
> + };
> +
> + isc_clk: isc_clk {
> + #clock-cells = <0>;
> + reg = <46>;
> + };
> +
> + qspi0_clk: qspi0_clk {
> + #clock-cells = <0>;
> + reg = <52>;
> + };
> +
> + qspi1_clk: qspi1_clk {
> + #clock-cells = <0>;
> + reg = <53>;
> + };
> + };
> + };
> +
> + sha@f0028000 {
> + compatible = "atmel,at91sam9g46-sha";
> + reg = <0xf0028000 0x100>;
> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(30))>;
> + dma-names = "tx";
> + clocks = <&sha_clk>;
> + clock-names = "sha_clk";
> + status = "disabled";
> + };
> +
> + aes@f002c000 {
> + compatible = "atmel,at91sam9g46-aes";
> + reg = <0xf002c000 0x100>;
> + interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(26))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(27))>;
> + dma-names = "tx", "rx";
> + clocks = <&aes_clk>;
> + clock-names = "aes_clk";
> + status = "disabled";
> + };
> +
> + spi0: spi@f8000000 {
> + compatible = "atmel,at91rm9200-spi";
> + reg = <0xf8000000 0x100>;
> + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(6))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(7))>;
> + dma-names = "tx", "rx";
> + clocks = <&spi0_clk>;
> + clock-names = "spi_clk";
> + atmel,fifo-size = <16>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + macb0: ethernet@f8008000 {
> + compatible = "atmel,sama5d2-gem";
> + reg = <0xf8008000 0x1000>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 0 */
> + 66 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 1 */
> + 67 IRQ_TYPE_LEVEL_HIGH 3>; /* Queue 2 */
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&macb0_clk>, <&macb0_clk>;
> + clock-names = "hclk", "pclk";
> + status = "disabled";
> + };
> +
> + tcb0: timer@f800c000 {
> + compatible = "atmel,at91sam9x5-tcb";
> + reg = <0xf800c000 0x100>;
> + interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&tcb0_clk>;
> + clock-names = "t0_clk";
> + };
> +
> + tcb1: timer@f8010000 {
> + compatible = "atmel,at91sam9x5-tcb";
> + reg = <0xf8010000 0x100>;
> + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&tcb1_clk>;
> + clock-names = "t0_clk";
> + };
> +
> + uart0: serial@f801c000 {
> + compatible = "atmel,at91sam9260-usart";
> + reg = <0xf801c000 0x100>;
> + interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&uart0_clk>;
> + clock-names = "usart";
> + status = "disabled";
> + };
> +
> + uart1: serial@f8020000 {
> + compatible = "atmel,at91sam9260-usart";
> + reg = <0xf8020000 0x100>;
> + interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&uart1_clk>;
> + clock-names = "usart";
> + status = "disabled";
> + };
> +
> + uart2: serial@f8024000 {
> + compatible = "atmel,at91sam9260-usart";
> + reg = <0xf8024000 0x100>;
> + interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&uart2_clk>;
> + clock-names = "usart";
> + status = "disabled";
> + };
> +
> + i2c0: i2c@f8028000 {
> + compatible = "atmel,sama5d2-i2c";
> + reg = <0xf8028000 0x100>;
> + interrupts = <29 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(0))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(1))>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&twi0_clk>;
> + status = "disabled";
> + };
> +
> + pit: timer@f8048030 {
> + compatible = "atmel,at91sam9260-pit";
> + reg = <0xf8048030 0x10>;
> + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 5>;
> + clocks = <&h32ck>;
> + };
> +
> + sckc@f8048050 {
> + compatible = "atmel,at91sam9x5-sckc";
> + reg = <0xf8048050 0x4>;
> +
> + slow_rc_osc: slow_rc_osc {
> + compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-accuracy = <250000000>;
> + atmel,startup-time-usec = <75>;
> + };
> +
> + slow_osc: slow_osc {
> + compatible = "atmel,at91sam9x5-clk-slow-osc";
> + #clock-cells = <0>;
> + clocks = <&slow_xtal>;
> + atmel,startup-time-usec = <1200000>;
> + };
> +
> + clk32k: slowck {
> + compatible = "atmel,at91sam9x5-clk-slow";
> + #clock-cells = <0>;
> + clocks = <&slow_rc_osc &slow_osc>;
> + };
> + };
> +
> + rtc@f80480b0 {
> + compatible = "atmel,at91rm9200-rtc";
> + reg = <0xf80480b0 0x30>;
> + interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
> + };
> +
> + spi1: spi@fc000000 {
> + compatible = "atmel,at91rm9200-spi";
> + reg = <0xfc000000 0x100>;
> + interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(8))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(9))>;
> + dma-names = "tx", "rx";
> + clocks = <&spi1_clk>;
> + clock-names = "spi_clk";
> + atmel,fifo-size = <16>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart3: serial@fc008000 {
> + compatible = "atmel,at91sam9260-usart";
> + reg = <0xfc008000 0x100>;
> + interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&uart3_clk>;
> + clock-names = "usart";
> + status = "disabled";
> + };
> +
> + uart4: serial@fc00c000 {
> + compatible = "atmel,at91sam9260-usart";
> + reg = <0xfc00c000 0x100>;
> + interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
> + clocks = <&uart4_clk>;
> + clock-names = "usart";
> + status = "disabled";
> + };
> +
> + aic: interrupt-controller@fc020000 {
> + #interrupt-cells = <3>;
> + compatible = "atmel,sama5d2-aic";
> + interrupt-controller;
> + reg = <0xfc020000 0x200>;
> + atmel,external-irqs = <49>;
> + };
> +
> + i2c1: i2c@fc028000 {
> + compatible = "atmel,sama5d2-i2c";
> + reg = <0xfc028000 0x100>;
> + interrupts = <30 IRQ_TYPE_LEVEL_HIGH 7>;
> + dmas = <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(2))>,
> + <&dma0
> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> + AT91_XDMAC_DT_PERID(3))>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&twi1_clk>;
> + status = "disabled";
> + };
> + };
> + };
> +};
>

--
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Michal Hocko: "Re: Re: [V2 PATCH 1/3] x86/panic: Fix re-entrance problem due to panic on NMI"
Previous message: Stephen Rothwell: "Re: linux-next: build failure after merge of the block tree"
In reply to: Nicolas Ferre: "[PATCH v3 2/3] ARM: at91/dt: add basic dtsi for sama5d2 SoC"
Next in thread: Nicolas Ferre: "[PATCH v3 3/3] ARM: at91/dt: add minimal sama5d2 Xplained board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]