Re: PCIe 32-bit MMIO exhaustion

From: Daniel J Blueman
Date: Wed Mar 04 2015 - 02:13:05 EST


On 04/03/2015 06:38, Bjorn Helgaas wrote:
[+cc linux-pci, linux-acpi]

On Tue, Feb 24, 2015 at 12:37:39PM +0800, Daniel J Blueman wrote:
Hi Bjorn, Jiang,

On 29/01/2015 23:23, Bjorn Helgaas wrote:
Hi Daniel,

On Wed, Jan 28, 2015 at 2:42 AM, Daniel J Blueman <daniel@xxxxxxxxxxxxx> wrote:
With systems with a large number of PCI devices, we're seeing lack of 32-bit
MMIO space, eg one quad-port NetXtreme-2 adapter takes 128MB of space [1].

An errata to the PCIe 2.1 spec provides guidance on limitations with 64-bit
non-prefetchable BARs (since bridges have only 32-bit non-prefetchable
ranges) stating that vendors can enable the prefetchable bit in BARs under
certain circumstances to allow 64-bit allocation [2].

The problem with that, is that vendors can't know apriori what hosts their
products will be in, so can't just advertise prefetchable 64-bit BARs. What
can be done, is system firmware can use the 64-bit prefetchable BAR in
bridges, and assign a 64-bit non-prefetchable device BAR into that area,
where it is safe to do so (following the guidance).

At present, linux denies such allocations [3] and disables the BARs. It
seems a practical solution to allow them if the firmware believes it is
safe.

This particular message ([3]):

pci 0002:01:00.0: BAR 0: [mem size 0x00002000 64bit] conflicts with PCI Bus
0002:00 [mem 0x10020000000-0x10027ffffff pref]

is misleading at best and likely a symptom of a bug. We printed the
*size* of BAR 0, not an address, which means we haven't assigned space
for the BAR. That means it should not conflict with anything.

We already do revert to firmware assignments in some situations when
Linux can't figure out how to assign things itself. But apparently
not in *this* situation.

Without seeing the whole picture, it's hard for me to figure out
what's going on here. Could you open a bug report at
http://bugzilla.kernel.org (category drivers/PCI) and attach a
complete dmesg and "lspci -vv" output? Then we can look at what
firmware did and what Linux thought was wrong with it.

Done a while back:
https://bugzilla.kernel.org/show_bug.cgi?id=92671

An interesting question popped up: I find the kernel doesn't accept
IO BARs and bridge windows after address 0xffff, though the PCI spec
and modern hardware allows 32-bit decode.

Thus for practical reasons, our NumaConnect firmware doesn't setup
IO BARs/windows beyond the first PCI domain (which is the only one
with legacy support, and no drivers seem to require IO their BARs
anyway), ...

If we don't handle IO ports above 0xffff, I think that's broken. I'm
pretty sure we do handle that on ia64 (it's done by assigning 64K of IO
space to each host bridge, and I think it's typically translated by the
bridge so each root bus sees a 0-64K space on PCI). We should be able to
do something similar on x86, but it may not be implemented there yet.

and we get conflicts and warnings [1]:

pnp 00:00: disabling [io 0x0061] because it overlaps 0001:05:00.0
BAR 0 [io 0x0000-0x00ff]
pci 0001:03:00.0: BAR 13: no space for [io size 0x1000]
pci 0001:03:00.0: BAR 13: failed to assign [io size 0x1000]

Is there a cleaner way of dealing with this, in our firmware and/or
the kernel? Eg, I guess if IO BARs aren't assigned (value 0) on PCI
domains without IO bridge windows in the ACPI AML, no need to
conflict/attempt assignment?

Yes, we should be able to deal with this better.

The complaint about disabling the pnp 00:00 resource is bogus because the
PCI 0001:05:00.0 BAR is not assigned and should never be enabled, so this
is not a real conflict. My intent is that the PCI resource corresponding
to this BAR should have the IORESOURCE_UNSET bit set. That will prevent
pci_enable_resources() from setting the PCI_COMMAND_IO bit, which is what
would enable the BAR.

Can you try the patch below? I don't think it will work right off the bat
because I think the fact that we print "[io 0x0000-0x00ff]" instead of
"[io size 0x0100]" means we don't have IORESOURCE_UNSET set in the PCI
resource. But maybe you can figure out where it *should* be getting
set?

Bjorn


commit fd4888cf942a2ae9cdefc46d1fba86b2c7ec2dbf
Author: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Date: Tue Mar 3 16:13:56 2015 -0600

PNP: Don't check for overlaps with unassigned PCI BARs

After 0509ad5e1a7d ("PNP: disable PNP motherboard resources that overlap
PCI BARs"), we disable and warn about PNP resources that overlap PCI BARs.
But we assume that all PCI BARs are valid, which is incorrect, because a
BAR may not have any space assigned to it. In that case, we will not
enable the BAR, so no other resource can conflict with it.

Ignore PCI BARs that are unassigned, as indicated by IORESOURCE_UNSET.

Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>

diff --git a/drivers/pnp/quirks.c b/drivers/pnp/quirks.c
index ebf0d6710b5a..943c1cb9566c 100644
--- a/drivers/pnp/quirks.c
+++ b/drivers/pnp/quirks.c
@@ -246,13 +246,16 @@ static void quirk_system_pci_resources(struct pnp_dev *dev)
*/
for_each_pci_dev(pdev) {
for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
- unsigned long type;
+ unsigned long flags, type;

- type = pci_resource_flags(pdev, i) &
- (IORESOURCE_IO | IORESOURCE_MEM);
+ flags = pci_resource_flags(pdev, i);
+ type = flags & (IORESOURCE_IO | IORESOURCE_MEM);
if (!type || pci_resource_len(pdev, i) == 0)
continue;

+ if (flags & IORESOURCE_UNSET)
+ continue;
+
pci_start = pci_resource_start(pdev, i);
pci_end = pci_resource_end(pdev, i);
for (j = 0;


Your patch solves the conflicts nicely [1] with:

From f835b16b0758a1dde6042a0e4c8aa5a2e8be5f21 Mon Sep 17 00:00:00 2001
From: Daniel J Blueman <daniel@xxxxxxxxxxxxx>
Date: Wed, 4 Mar 2015 14:53:00 +0800
Subject: [PATCH] Mark PCI BARs with address 0 as unset

Allow the kernel to activate the unset flag for PCI BAR resources if
the firmware assigns address 0 (invalid as legacy IO is in this range).

This allows preventing conflicts with legacy IO/ACPI PNP resources in
this range.

Signed-off-by: Daniel J Blueman <daniel@xxxxxxxxxxxxx>
---
drivers/pci/probe.c | 7 +++++++
1 file changed, 7 insertions(+)

diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 8d2f400..ef43652 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -281,6 +281,13 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
pcibios_resource_to_bus(dev->bus, &inverted_region, res);

/*
+ * If firmware doesn't assign a valid PCI address (as legacy IO is below
+ * PCI IO), mark resource unset to prevent later resource conflicts
+ */
+ if (region.start == 0)
+ res->flags |= IORESOURCE_UNSET;
+
+ /*
* If "A" is a BAR value (a bus address), "bus_to_resource(A)" is
* the corresponding resource address (the physical address used by
* the CPU. Converting that resource address back to a bus address

[1] https://resource.numascale.com/dmesg-4.0.0-rc2.txt
--
Daniel J Blueman
Principal Software Engineer, Numascale
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/