Re: [PATCH 1/4] pinctrl: Broadcom Cygnus pinctrl device tree binding

From: Ray Jui
Date: Tue Jan 13 2015 - 12:14:48 EST




On 1/13/2015 12:20 AM, Linus Walleij wrote:
> On Fri, Jan 9, 2015 at 7:26 PM, Ray Jui <rjui@xxxxxxxxxxxx> wrote:
>> On 1/9/2015 2:12 AM, Linus Walleij wrote:
>
>>> Just use "groups" and "function" and refer to
>>> Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
>>>
>>> Then "alt1", "alt2" etc are non-functional names of functions.
>>> Use the real function names, like "spi0" or so. This
>>> alt-business seems to be just a shortcut to make it
>>> simple, don't do that.
>>>
>>> Then you use e.g. "spi0" as a group name. I prefer you
>>> call that "spi0_grp" or something to say it is a group of
>>> pins associated with spi0, as spi0 is actually the
>>> function.
>>>
>> Hmmm, I did this by following brcm,bcm11351-pinctrl.txt:
>> - function: String. Specifies the pin mux selection. Values must be one
>> of: "alt1", "alt2", "alt3", "alt4"
>>
>> But you are right, in the pinctrl binding document it describes the
>> generic pin multiplexing nodes use "function" and "group".
>
> Note "function" and "groups". Note groups is pluralis. You can
> select multiple groups for a single function.
>
>> For example, the group "lcd" covers 30 pins. When I configure "lcd" to
>> alternate function 1, all 30 pins are muxed to LCD function. When
>> configured to function 2, all pins are muxed to SRAM function. Now, here
>> comes the issue, when configured to function 3, pins 1-15 and 20-30
>> become GPIO function, but pins 16-19 becomes SPI5 function. When it's
>> configured to function 4, all 30 pins become GPIO.
>
> I would split the use case in two groups for LCD and SRAM,
> and three groups for GPIO:
> "lcd_grp", "sram_grp", "gpio-1-15_grp",
> "gpio-16-19_grp", "gpio-20-30_grp", "spi5_grp"
>

> Valid combinations become
>
> function = "lcd"
> groups = "lcd_grp";
>
> function = "sram"
> groups = "sram_grp"
>
> For all GPIO only this:
>
> function = "gpio"
> groups = "gpio-1-16_grp", "gpio-16-19_grp", "gpio-20-30_grp"
>
> For a combined GPIO+SPI:
>
> function = "gpio"
> groups = "gpio-1-16_grp", "gpio-20-30_grp"
>
> function = "spi5"
> groups = "spi5_grp"
>
> The pinctrl runtile will protest if you try to combine spi5_grp
> with gpio-16-19_grp.
>
Okay this makes sense. Thanks.

>> In some other cases, when I configure a group to other functions, there
>> could be spare pins which become unused (not brought out to the pad).
>> Or, the spare pins may also become a separate function.
>
> That's cool.
>
>> Based on the LCD example, I'd assume I would do the following for the
>> default LCD function:
>>
>> lcd_node {
>> group = "lcd_grp";
>> function = "lcd";
>> };
>>
>> And in the case of function 3, I would call the function "spi5" and
>> assume the rest of pins become either GPIO (or unused)?
>>
>> spi5_node {
>> group = "lcd_grp";
>> function = "spi5";
>> };
>
> Looks cool per above.
>
> You need some clever code in the driver to handle double-configuration
> of registers and so on, but I think it can be done.
Let me see what I can come up with.

>
> Using pin control as a GPIO backend can be a bit tricky and will need
> some testing and elaboration, but the subsystem will block collisions.
>
> Yours,
> Linus Walleij
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/