[PATCH 2/5] MN10300: Remove Kconfig symbols depending on GDBSTUB

[Paul Bolle]

The Kconfig symbol GDBSTUB was removed. Remove all symbols (indirectly)
depending on it. And remove it as an (optional) dependency for the
symbol KERNEL_DEBUGGER.

Signed-off-by: Paul Bolle <pebolle@xxxxxxxxxx>
---
 arch/mn10300/Kconfig.debug | 105 +--------------------------------------------
 1 file changed, 1 insertion(+), 104 deletions(-)

diff --git a/arch/mn10300/Kconfig.debug b/arch/mn10300/Kconfig.debug
index 6a8c7e8d6156..a1acb29f6b2a 100644
--- a/arch/mn10300/Kconfig.debug
+++ b/arch/mn10300/Kconfig.debug
@@ -30,111 +30,8 @@ config KPROBES
 	  for kernel debugging, non-intrusive instrumentation and testing.
 	  If in doubt, say "N".
 
-config GDBSTUB_IMMEDIATE
-	bool "Break into GDB stub immediately"
-	depends on GDBSTUB
-	help
-	  If you say Y here, GDB stub will break into the program as soon as
-	  possible, leaving the program counter at the beginning of
-	  start_kernel() in init/main.c.
-
-config GDBSTUB_ALLOW_SINGLE_STEP
-	bool "Allow software single-stepping in GDB stub"
-	depends on GDBSTUB && !SMP && !PREEMPT
-	help
-	  Allow GDB stub to perform software single-stepping through the
-	  kernel.  This doesn't work very well on SMP or preemptible kernels as
-	  it uses temporary breakpoints to emulate single-stepping.
-
-config GDB_CONSOLE
-	bool "Console output to GDB"
-	depends on GDBSTUB
-	help
-	  If you are using GDB for remote debugging over a serial port and
-	  would like kernel messages to be formatted into GDB $O packets so
-	  that GDB prints them as program output, say 'Y'.
-
-config GDBSTUB_DEBUGGING
-	bool "Debug GDB stub by messages to serial port"
-	depends on GDBSTUB
-	help
-	  This causes debugging messages to be displayed at various points
-	  during execution of the GDB stub routines. Such messages will be
-	  displayed on ttyS0 if that isn't the GDB stub's port, or ttySM0
-	  otherwise.
-
-config GDBSTUB_DEBUG_ENTRY
-	bool "Debug GDB stub entry"
-	depends on GDBSTUB_DEBUGGING
-	help
-	  This option causes information to be displayed about entry to or exit
-	  from the main GDB stub routine.
-
-config GDBSTUB_DEBUG_PROTOCOL
-	bool "Debug GDB stub protocol"
-	depends on GDBSTUB_DEBUGGING
-	help
-	  This option causes information to be displayed about the GDB remote
-	  protocol messages generated exchanged with GDB.
-
-config GDBSTUB_DEBUG_IO
-	bool "Debug GDB stub I/O"
-	depends on GDBSTUB_DEBUGGING
-	help
-	  This option causes information to be displayed about GDB stub's
-	  low-level I/O.
-
-config GDBSTUB_DEBUG_BREAKPOINT
-	bool "Debug GDB stub breakpoint management"
-	depends on GDBSTUB_DEBUGGING
-	help
-	  This option causes information to be displayed about GDB stub's
-	  breakpoint management.
-
-choice
-	prompt "GDB stub port"
-	default GDBSTUB_ON_TTYSM0
-	depends on GDBSTUB
-	help
-	  Select the serial port used for GDB-stub.
-
-config GDBSTUB_ON_TTYSM0
-	bool "/dev/ttySM0 [SIF0]"
-	depends on MN10300_TTYSM0
-	select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYSM1
-	bool "/dev/ttySM1 [SIF1]"
-	depends on MN10300_TTYSM1
-	select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYSM2
-	bool "/dev/ttySM2 [SIF2]"
-	depends on MN10300_TTYSM2
-	select GDBSTUB_ON_TTYSMx
-
-config GDBSTUB_ON_TTYS0
-	bool "/dev/ttyS0"
-	select GDBSTUB_ON_TTYSx
-
-config GDBSTUB_ON_TTYS1
-	bool "/dev/ttyS1"
-	select GDBSTUB_ON_TTYSx
-
-endchoice
-
-config GDBSTUB_ON_TTYSMx
-	bool
-	depends on GDBSTUB_ON_TTYSM0 || GDBSTUB_ON_TTYSM1 || GDBSTUB_ON_TTYSM2
-	default y
-
-config GDBSTUB_ON_TTYSx
-	bool
-	depends on GDBSTUB_ON_TTYS0 || GDBSTUB_ON_TTYS1
-	default y
-
 endmenu
 
 config KERNEL_DEBUGGER
 	def_bool y
-	depends on GDBSTUB || KGDB
+	depends on KGDB
-- 
1.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/