Re: [PATCH] mmc: rtsx: add card power off during probe

From: Ulf Hansson
Date: Wed Sep 17 2014 - 15:29:10 EST


On 17 September 2014 11:11, micky <micky_ching@xxxxxxxxxxxxxx> wrote:
> On 09/17/2014 02:01 AM, Ulf Hansson wrote:
>>
>> On 12 September 2014 03:39, <micky_ching@xxxxxxxxxxxxxx> wrote:
>>>
>>> From: Roger Tseng <rogerable@xxxxxxxxxxx>
>>>
>>> Some platform have both UEFI driver and MFD/mmc driver, if entering
>>> linux while card in the slot, the card power is already on, and rtsx-mmc
>>> driver have no chance to make card power off. This will lead UHSI card
>>> failed to enter UHSI mode.
>>>
>>> It is hard to control the UEFI driver leaving state, so we power off the
>>> card power during probe.
>>>
>>> Signed-off-by: Roger Tseng <rogerable@xxxxxxxxxxx>
>>> Signed-off-by: Micky Ching <micky_ching@xxxxxxxxxxxxxx>
>>> ---
>>> drivers/mmc/host/rtsx_pci_sdmmc.c | 7 ++++++-
>>> 1 file changed, 6 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c
>>> b/drivers/mmc/host/rtsx_pci_sdmmc.c
>>> index dfde4a2..57b0796 100644
>>> --- a/drivers/mmc/host/rtsx_pci_sdmmc.c
>>> +++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
>>> @@ -1341,8 +1341,13 @@ static int rtsx_pci_sdmmc_drv_probe(struct
>>> platform_device *pdev)
>>> host->pcr = pcr;
>>> host->mmc = mmc;
>>> host->pdev = pdev;
>>> - host->power_state = SDMMC_POWER_OFF;
>>> INIT_WORK(&host->work, sd_request);
>>> + sd_power_off(host);
>>> + /*
>>> + * ref: SD spec 3.01: 6.4.1.2 Power On or Power Cycle
>>> + */
>>> + usleep_range(1000, 2000);
>>> +
>>
>> This won't work in cases were you power off eMMC cards, unless you can
>> do a full power cycle - cut both VCC and VCCQ. Can you?
>
> Hi Uffe,
>
> VCCQ will poweroff at the same time.

In that case, don't forget to enable MMC_CAP2_FULL_PWR_CYCLE.

>
> if MMC_CAP2_NO_PRESCAN_POWERUP enable, will call mmc_power_off() at start,
> then it will check ios.power_mode, but the state is MMC_POWER_OFF and just
> return.

Uhh, that's right! So, I wonder why we invokes mmc_power_off() from
that path at all.

Hmm, I think we should change the behavior in mmc_start_host(), like below:
1) Add a "MMC_POWER_UNDEFINED" state which is what the power state
should be assigned to at allocation.
2 ) From mmc_start_host(), invoke mmc_power_off() when
MMC_CAP2_NO_PRESCAN_POWERUP and MMC_CAP2_FULL_PWR_CYCLE is set.

Would that work?

Kind regards
Uffe

> Best Regards.
> micky.
>
>> There are also another option you might want to use,
>> MMC_CAP2_NO_PRESCAN_POWERUP. But again, it must only be used for those
>> hosts that you are able to do a full power cycle for.
>>
>> Kind regards
>> Uffe
>>
>>> platform_set_drvdata(pdev, host);
>>> pcr->slots[RTSX_SD_CARD].p_dev = pdev;
>>> pcr->slots[RTSX_SD_CARD].card_event = rtsx_pci_sdmmc_card_event;
>>> --
>>> 1.7.9.5
>>>
>> .
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/