Re: [PATCH] i2c: i2c-tegra: Move clk_prepare/clk_set_rate to probe

From: Stephen Warren
Date: Fri Aug 15 2014 - 12:18:07 EST


On 08/15/2014 03:47 AM, Mikko Perttunen wrote:
Currently the i2c-tegra bus driver prepares, enables
and set_rates its clocks separately for each transfer.
This causes locking problems when doing I2C transfers
from clock notifiers; see
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-July/268653.html

This patch moves clk_prepare/unprepare and clk_set_rate calls to
the probe function, leaving only clk_enable/disable to be
done on each transfer. This solves the locking issue.

diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c

@@ -380,34 +380,33 @@ static inline int tegra_i2c_clock_enable(struct tegra_i2c_dev *i2c_dev)
{
int ret;
if (!i2c_dev->hw->has_single_clk_source) {
- ret = clk_prepare_enable(i2c_dev->fast_clk);
+ ret = clk_enable(i2c_dev->fast_clk);

Here, both the prepare and enable wrap just the I2C transfer, ...

@@ -428,9 +427,6 @@ static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev)
i2c_writel(i2c_dev, val, I2C_CNFG);
i2c_writel(i2c_dev, 0, I2C_INT_MASK);

- clk_multiplier *= (i2c_dev->hw->clk_divisor_std_fast_mode + 1);
- clk_set_rate(i2c_dev->div_clk, i2c_dev->bus_clk_rate * clk_multiplier);

... whereas the rate is set up when the controller is initialized, i.e. much earlier.

@@ -777,17 +774,39 @@ static int tegra_i2c_probe(struct platform_device *pdev)

+ if (!i2c_dev->hw->has_single_clk_source) {
+ ret = clk_prepare(i2c_dev->fast_clk);
+ if (ret < 0) {
+ dev_err(i2c_dev->dev, "Clock prepare failed %d\n", ret);
+ return ret;
+ }
+ }
+
+ ret = clk_prepare(i2c_dev->div_clk);
+ if (ret < 0) {
+ dev_err(i2c_dev->dev, "Clock prepare failed %d\n", ret);
+ goto unprepare_fast_clk;
+ }
+
+ clk_multiplier *= (i2c_dev->hw->clk_divisor_std_fast_mode + 1);
+ ret = clk_set_rate(i2c_dev->div_clk,
+ i2c_dev->bus_clk_rate * clk_multiplier);
+ if (ret) {
+ dev_err(i2c_dev->dev, "Clock rate change failed %d\n", ret);
+ goto unprepare_div_clk;
+ }

However, the new code sets the clock rate after the clock is prepared. I think the rate should be set first, then the clock prepared. While this likely doesn't apply to the Tegra clock controller, prepare() is allowed to enable the clock if enable() can't be implemented in an atomic fashion (in which case enable/disable would be no-ops), and we should make sure that the driver correctly configures the clock before potentially enabling it.

I'm not sure if a similar change to our SPI drivers is possible; after all, the SPI transfer rate can vary per message, so if clk_set_rate() acquires a lock, it seems there's no way to avoid the issue there. Luckily, we don't have any SPI-based chips that do anything related to clocks on any of our current boards...

Aside from this issue, the patch looks fine to me.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/