[RESEND PATCHv2 2/2] dt-bindings: regulator: Add regulator suspend state for PM state

From: Chanwoo Choi
Date: Wed Jul 09 2014 - 00:48:35 EST


This patch add regulator suspend state to constraint in dt file. The regulation_
constraints structure already has regulator suspend state field as following.
The regulator suspend state control the state of regulator according to
PM (Power Management) state.
- struct regulator_state state_disk
- struct regulator_state state_mem
- struct regulator_state state_standby

Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
---
.../devicetree/bindings/regulator/regulator.txt | 32 ++++++++++++++++++++++
1 file changed, 32 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 8607433..c4f566a 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -19,6 +19,33 @@ Optional properties:
design requires. This property describes the total system ramp time
required due to the combination of internal ramping of the regulator itself,
and board design issues such as trace capacitance and load on the supply.
+- regulator-initial-state: initial state for suspend state, cnd set initial
+ state among following defined suspend states:
+ <2>: PM_SUSPEND_STANDBY - Setup regulator according to regulator-state-standby
+ <3>: PM_SUSPEND_MEM - Setup regulator according to regulator-state-mem
+ <4>: PM_SUSPEND_MAX - Setup regulator according to regulator-state-disk
+- regulator-state-standby sub-root node for Standby mode
+ : the device is in a power-saving state, but can also receive certain events,
+ specific behavior depends on the specific device.
+- regulator-state-mem sub-root node for Suspend-to-RAM mode
+ : suspend to memory, the device goes to sleep, but all data stored in memory,
+ only some external interrupt can wake the device.
+- regulator-state-disk sub-root node for Suspend-to-disk mode
+ : suspend to disk, this state operates similarly to Suspend-to-RAM,
+ but includes a final step of writing memory contents to disk.
+- regulator-state-[standby/mem/disk] node has following common properties:
+ - regulator-volt: voltage consumers may set in suspend state.
+ - regulator-mode: voltage mode in suspend state, can set mode among
+ following defined regulator modes:
+ 0x1: REGULATOR_MODE_FAST, Regulator can handle fast changes.
+ 0x2: REGULATOR_MODE_NORMAL, Normal regulator power supply mode.
+ 0x4: REGULATOR_MODE_IDLE, Regulator runs in a more efficient mode.
+ 0x8: REGULATOR_MODE_STANDBY, Regulator runs in the most efficient mode.
+ - regulator-on-in-suspend: regulator should be on in suspend state.
+ - regulator-off-in-suspend: regulator should be off in suspend state.
+ If node don't include regulator-[on/off]-in-suspend, can't change
+ regulator state in suspend mode and only should sustain the regulator
+ state of normal state.

Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
@@ -34,6 +61,11 @@ Example:
regulator-max-microvolt = <2500000>;
regulator-always-on;
vin-supply = <&vin>;
+
+ regulator-state-mem {
+ regulator-volt = <1000000>;
+ regulator-off-in-suspend;
+ };
};

Regulator Consumers:
--
1.8.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/