[PATCH v2 13/14] mmc: mmci: add qcom specific clk control

[srinivas . kandagatla]

From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>

On Qcom SD card controller, cclk is mclk and mclk should be directly
controlled by the driver.
This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control and cclk_is_mclk flags in variant structure giving
more flexibility to the driver.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
 drivers/mmc/host/mmci.c | 30 +++++++++++++++++++++++++-----
 1 file changed, 25 insertions(+), 5 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index bc7b80d..cf58fec1 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -75,6 +75,8 @@ static unsigned int fmax = 515633;
  * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
  * @mclk_delayed_writes: enable delayed writes to ensure, subsequent updates
  *			 are not ignored.
+ * @explicit_mclk_control: enable explicit mclk control in driver.
+ * @qcom_cclk_is_mclk: enable iff card clock is multimedia card adapter clock.
  */
 struct variant_data {
 	unsigned int		clkreg;
@@ -97,6 +99,8 @@ struct variant_data {
 	bool			busy_detect;
 	bool			pwrreg_nopower;
 	bool			mclk_delayed_writes;
+	bool			explicit_mclk_control;
+	bool			qcom_cclk_is_mclk;
 };
 
 static struct variant_data variant_arm = {
@@ -205,6 +209,8 @@ static struct variant_data variant_qcom = {
 	 * for 3 clk cycles.
 	 */
 	.mclk_delayed_writes	= true,
+	.explicit_mclk_control	= true,
+	.qcom_cclk_is_mclk	= true,
 };
 
 static inline u32 mmci_readl(struct mmci_host *host, u32 off)
@@ -320,7 +326,9 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
 	host->cclk = 0;
 
 	if (desired) {
-		if (desired >= host->mclk) {
+		if (variant->qcom_cclk_is_mclk) {
+			host->cclk = host->mclk;
+		} else if (desired >= host->mclk) {
 			clk = MCI_CLK_BYPASS;
 			if (variant->st_clkdiv)
 				clk |= MCI_ST_UX500_NEG_EDGE;
@@ -1358,6 +1366,16 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	if (!ios->clock && variant->pwrreg_clkgate)
 		pwr &= ~MCI_PWR_ON;
 
+	if (ios->clock != host->mclk && host->variant->explicit_mclk_control) {
+		int rc = clk_set_rate(host->clk, ios->clock);
+		if (rc < 0) {
+			dev_err(mmc_dev(host->mmc),
+				"Error setting clock rate (%d)\n", rc);
+		} else {
+			host->mclk = clk_get_rate(host->clk);
+		}
+	}
+
 	spin_lock_irqsave(&host->lock, flags);
 
 	mmci_set_clkreg(host, ios->clock);
@@ -1544,10 +1562,12 @@ static int mmci_probe(struct amba_device *dev,
 	 * is not specified. Either value must not exceed the clock rate into
 	 * the block, of course.
 	 */
-	if (mmc->f_max)
-		mmc->f_max = min(host->mclk, mmc->f_max);
-	else
-		mmc->f_max = min(host->mclk, fmax);
+	if (!host->variant->explicit_mclk_control) {
+		if (mmc->f_max)
+			mmc->f_max = min(host->mclk, mmc->f_max);
+		else
+			mmc->f_max = min(host->mclk, fmax);
+	}
 	dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
 
 	/* Get regulators and the supported OCR mask */
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/