[PATCH 11/11] iio: pressure-core: st: Provide correct regulator support

[Lee Jones]

The power to some of the sensors are controlled by regulators. In most
cases these are 'always on', but if not they will fail to work until
the regulator is enabled using the relevant APIs.

Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
 drivers/iio/pressure/st_pressure_core.c | 13 +++++++++++++
 include/linux/iio/common/st_sensors.h   |  3 +++
 2 files changed, 16 insertions(+)

diff --git a/drivers/iio/pressure/st_pressure_core.c b/drivers/iio/pressure/st_pressure_core.c
index f452417..7beed89 100644
--- a/drivers/iio/pressure/st_pressure_core.c
+++ b/drivers/iio/pressure/st_pressure_core.c
@@ -23,6 +23,7 @@
 #include <linux/iio/sysfs.h>
 #include <linux/iio/trigger.h>
 #include <linux/iio/buffer.h>
+#include <linux/regulator/consumer.h>
 #include <asm/unaligned.h>
 
 #include <linux/iio/common/st_sensors.h>
@@ -315,6 +316,15 @@ int st_press_common_probe(struct iio_dev *indio_dev)
 	indio_dev->modes = INDIO_DIRECT_MODE;
 	indio_dev->info = &press_info;
 
+	/* Regulator not mandatory, but if requested we should enable it. */
+	pdata->regulator = regulator_get(&indio_dev->dev, "vdd");
+	if (!IS_ERR_OR_NULL(pdata->regulator)) {
+		err = regulator_enable(pdata->regulator);
+		if (err != 0)
+			dev_warn(&indio_dev->dev,
+				 "Failed to enable specified vdd regulator\n");
+	}
+
 	err = st_sensors_check_device_support(indio_dev,
 					      ARRAY_SIZE(st_press_sensors),
 					      st_press_sensors);
@@ -363,6 +373,9 @@ void st_press_common_remove(struct iio_dev *indio_dev)
 {
 	struct st_sensor_data *pdata = iio_priv(indio_dev);
 
+	if (!IS_ERR_OR_NULL(pdata->regulator))
+		regulator_disable(pdata->regulator);
+
 	iio_device_unregister(indio_dev);
 	if (pdata->get_irq_data_ready(indio_dev) > 0) {
 		st_sensors_deallocate_trigger(indio_dev);
diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h
index 4aef925..eb6ef3f 100644
--- a/include/linux/iio/common/st_sensors.h
+++ b/include/linux/iio/common/st_sensors.h
@@ -16,6 +16,7 @@
 #include <linux/irqreturn.h>
 #include <linux/iio/trigger.h>
 #include <linux/bitops.h>
+#include <linux/regulator/consumer.h>
 
 #define ST_SENSORS_TX_MAX_LENGTH		2
 #define ST_SENSORS_RX_MAX_LENGTH		6
@@ -197,6 +198,7 @@ struct st_sensors {
  * @trig: The trigger in use by the core driver.
  * @sensor: Pointer to the current sensor struct in use.
  * @current_fullscale: Maximum range of measure by the sensor.
+ * @regulator: Pointer to sensor's power supply
  * @enabled: Status of the sensor (false->off, true->on).
  * @multiread_bit: Use or not particular bit for [I2C/SPI] multiread.
  * @buffer_data: Data used by buffer part.
@@ -211,6 +213,7 @@ struct st_sensor_data {
 	struct iio_trigger *trig;
 	struct st_sensors *sensor;
 	struct st_sensor_fullscale_avl *current_fullscale;
+	struct regulator *regulator;
 
 	bool enabled;
 	bool multiread_bit;
-- 
1.8.1.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/