[PATCH 4/4] netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYs

From: David Daney
Date: Fri Jun 22 2012 - 20:24:38 EST


From: David Daney <david.daney@xxxxxxxxxx>

Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.

If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.

Signed-off-by: David Daney <david.daney@xxxxxxxxxx>
---
.../devicetree/bindings/net/broadcom-bcm87xx.txt | 29 +++
drivers/net/phy/Kconfig | 5 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/bcm87xx.c | 239 ++++++++++++++++++++
4 files changed, 274 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
create mode 100644 drivers/net/phy/bcm87xx.c

diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
new file mode 100644
index 0000000..7c86d5e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt
@@ -0,0 +1,29 @@
+The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They
+have these bindings in addition to the standard PHY bindings.
+
+Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and
+ "ethernet-phy-ieee802.3-c45"
+
+Optional Properties:
+
+- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell
+ is the MDIO Manageable Device (MMD) address, the second a register
+ address within the MMD, the third cell contains a mask to be ANDed
+ with the existing register value, and the fourth cell is ORed with
+ he result to yield the new register value. If the third cell has a
+ value of zero, no read of the existing value is performed.
+
+Example:
+
+ ethernet-phy@5 {
+ reg = <5>;
+ compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45";
+ interrupt-parent = <&gpio>;
+ interrupts = <12 8>; /* Pin 12, active low */
+ /*
+ * Set PMD Digital Control Register for
+ * GPIO[1] Tx/Rx
+ * GPIO[0] R64 Sync Acquired
+ */
+ broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>;
+ };
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 944cdfb..3090dc6 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -67,6 +67,11 @@ config BCM63XX_PHY
---help---
Currently supports the 6348 and 6358 PHYs.

+config BCM87XX_PHY
+ tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
+ help
+ Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
+
config ICPLUS_PHY
tristate "Drivers for ICPlus PHYs"
---help---
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index f51af68..6d2dc6c 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_SMSC_PHY) += smsc.o
obj-$(CONFIG_VITESSE_PHY) += vitesse.o
obj-$(CONFIG_BROADCOM_PHY) += broadcom.o
obj-$(CONFIG_BCM63XX_PHY) += bcm63xx.o
+obj-$(CONFIG_BCM87XX_PHY) += bcm87xx.o
obj-$(CONFIG_ICPLUS_PHY) += icplus.o
obj-$(CONFIG_REALTEK_PHY) += realtek.o
obj-$(CONFIG_LSI_ET1011C_PHY) += et1011c.o
diff --git a/drivers/net/phy/bcm87xx.c b/drivers/net/phy/bcm87xx.c
new file mode 100644
index 0000000..b2f6a43
--- /dev/null
+++ b/drivers/net/phy/bcm87xx.c
@@ -0,0 +1,239 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 - 2012 Cavium, Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/of.h>
+
+#define PHY_ID_BCM8706 0x0143bdc1
+#define PHY_ID_BCM8727 0x0143bff0
+
+#define BCM87XX_PMD_RX_SIGNAL_DETECT (MII_ADDR_C45 | 0x1000a)
+#define BCM87XX_10GBASER_PCS_STATUS (MII_ADDR_C45 | 0x30020)
+#define BCM87XX_XGXS_LANE_STATUS (MII_ADDR_C45 | 0x40018)
+
+#define BCM87XX_LASI_CONTROL (MII_ADDR_C45 | 0x39002)
+#define BCM87XX_LASI_STATUS (MII_ADDR_C45 | 0x39005)
+
+#if IS_ENABLED(CONFIG_OF_MDIO)
+/*
+ * Set and/or override some configuration registers based on the
+ * marvell,reg-init property stored in the of_node for the phydev.
+ *
+ * broadcom,c45-reg-init = <devid reg mask value>,...;
+ *
+ * There may be one or more sets of <devid reg mask value>:
+ *
+ * devid: which sub-device to use.
+ * reg: the register.
+ * mask: if non-zero, ANDed with existing register value.
+ * value: ORed with the masked value and written to the regiser.
+ *
+ */
+static int bcm87xx_of_reg_init(struct phy_device *phydev)
+{
+ const __be32 *paddr;
+ const __be32 *paddr_end;
+ int len, ret;
+
+ if (!phydev->dev.of_node)
+ return 0;
+
+ paddr = of_get_property(phydev->dev.of_node,
+ "broadcom,c45-reg-init", &len);
+ if (!paddr)
+ return 0;
+
+ paddr_end = paddr + (len /= sizeof(*paddr));
+
+ ret = 0;
+
+ while (paddr + 3 < paddr_end) {
+ u16 devid = be32_to_cpup(paddr++);
+ u16 reg = be32_to_cpup(paddr++);
+ u16 mask = be32_to_cpup(paddr++);
+ u16 val_bits = be32_to_cpup(paddr++);
+ int val;
+ u32 regnum = MII_ADDR_C45 | (devid << 16) | reg;
+ val = 0;
+ if (mask) {
+ val = phy_read(phydev, regnum);
+ if (val < 0) {
+ ret = val;
+ goto err;
+ }
+ val &= mask;
+ }
+ val |= val_bits;
+
+ ret = phy_write(phydev, regnum, val);
+ if (ret < 0)
+ goto err;
+ }
+err:
+ return ret;
+}
+#else
+static int bcm87xx_of_reg_init(struct phy_device *phydev)
+{
+ return 0;
+}
+#endif /* CONFIG_OF_MDIO */
+
+static int bcm87xx_config_init(struct phy_device *phydev)
+{
+ phydev->supported = SUPPORTED_10000baseR_FEC;
+ phydev->advertising = ADVERTISED_10000baseR_FEC;
+ phydev->state = PHY_NOLINK;
+
+ bcm87xx_of_reg_init(phydev);
+
+ return 0;
+}
+
+static int bcm87xx_config_aneg(struct phy_device *phydev)
+{
+ return -EINVAL;
+}
+
+static int bcm87xx_read_status(struct phy_device *phydev)
+{
+ int rx_signal_detect;
+ int pcs_status;
+ int xgxs_lane_status;
+
+ rx_signal_detect = phy_read(phydev, BCM87XX_PMD_RX_SIGNAL_DETECT);
+ if (rx_signal_detect < 0)
+ return rx_signal_detect;
+
+ if ((rx_signal_detect & 1) == 0)
+ goto no_link;
+
+ pcs_status = phy_read(phydev, BCM87XX_10GBASER_PCS_STATUS);
+ if (pcs_status < 0)
+ return pcs_status;
+
+ if ((pcs_status & 1) == 0)
+ goto no_link;
+
+ xgxs_lane_status = phy_read(phydev, BCM87XX_XGXS_LANE_STATUS);
+ if (xgxs_lane_status < 0)
+ return xgxs_lane_status;
+
+ if ((xgxs_lane_status & 0x1000) == 0)
+ goto no_link;
+
+ phydev->speed = 10000;
+ phydev->link = 1;
+ phydev->duplex = 1;
+ return 0;
+
+no_link:
+ phydev->link = 0;
+ return 0;
+}
+
+static int bcm87xx_config_intr(struct phy_device *phydev)
+{
+ int reg, err;
+
+ reg = phy_read(phydev, BCM87XX_LASI_CONTROL);
+
+ if (reg < 0)
+ return reg;
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ reg |= 1;
+ else
+ reg &= ~1;
+
+ err = phy_write(phydev, BCM87XX_LASI_CONTROL, reg);
+ return err;
+}
+
+static int bcm87xx_did_interrupt(struct phy_device *phydev)
+{
+ int reg;
+
+ reg = phy_read(phydev, BCM87XX_LASI_STATUS);
+
+ if (reg < 0) {
+ dev_err(&phydev->dev,
+ "Error: Read of BCM87XX_LASI_STATUS failed: %d\n", reg);
+ return 0;
+ }
+ return (reg & 1) != 0;
+}
+
+static int bcm87xx_ack_interrupt(struct phy_device *phydev)
+{
+ /* Reading the LASI status clears it. */
+ bcm87xx_did_interrupt(phydev);
+ return 0;
+}
+
+static int bcm8706_match_phy_device(struct phy_device *phydev)
+{
+ return phydev->c45_ids.device_ids[4] == PHY_ID_BCM8706;
+}
+
+static int bcm8727_match_phy_device(struct phy_device *phydev)
+{
+ return phydev->c45_ids.device_ids[4] == PHY_ID_BCM8727;
+}
+
+static struct phy_driver bcm8706_driver = {
+ .phy_id = PHY_ID_BCM8706,
+ .phy_id_mask = 0xffffffff,
+ .name = "Broadcom BCM8706",
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = bcm87xx_config_init,
+ .config_aneg = bcm87xx_config_aneg,
+ .read_status = bcm87xx_read_status,
+ .ack_interrupt = bcm87xx_ack_interrupt,
+ .config_intr = bcm87xx_config_intr,
+ .did_interrupt = bcm87xx_did_interrupt,
+ .match_phy_device = bcm8706_match_phy_device,
+ .driver = { .owner = THIS_MODULE },
+};
+
+static struct phy_driver bcm8727_driver = {
+ .phy_id = PHY_ID_BCM8727,
+ .phy_id_mask = 0xffffffff,
+ .name = "Broadcom BCM8727",
+ .flags = PHY_HAS_INTERRUPT,
+ .config_init = bcm87xx_config_init,
+ .config_aneg = bcm87xx_config_aneg,
+ .read_status = bcm87xx_read_status,
+ .ack_interrupt = bcm87xx_ack_interrupt,
+ .config_intr = bcm87xx_config_intr,
+ .did_interrupt = bcm87xx_did_interrupt,
+ .match_phy_device = bcm8727_match_phy_device,
+ .driver = { .owner = THIS_MODULE },
+};
+
+static int __init bcm87xx_init(void)
+{
+ int ret;
+
+ ret = phy_driver_register(&bcm8706_driver);
+ if (ret)
+ goto err;
+
+ ret = phy_driver_register(&bcm8727_driver);
+err:
+ return ret;
+}
+module_init(bcm87xx_init);
+
+static void __exit bcm87xx_exit(void)
+{
+ phy_driver_unregister(&bcm8706_driver);
+ phy_driver_unregister(&bcm8727_driver);
+}
+module_exit(bcm87xx_exit);
--
1.7.2.3

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/