Re: [PATCH] ohci-nxp: add usbd and otg clock initialization

[Roland Stigge]

On 06/20/2012 02:02 PM, Alexandre Pereira da Silva wrote:
> The ohci-nxp was assuming the clock was enabled by the board init or
> bootloader and just enabling the pll. This enables the usbd and otg
> clocks this periferal also needs.
> 
> Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@xxxxxxxxx>

Acked-by: Roland Stigge <stigge@xxxxxxxxx>

> ---
>  drivers/usb/host/ohci-nxp.c |   88 +++++++++++++++++++++++++++----------------
>  1 file changed, 55 insertions(+), 33 deletions(-)
> 
> diff --git a/drivers/usb/host/ohci-nxp.c b/drivers/usb/host/ohci-nxp.c
> index 1e364ec..a446386 100644
> --- a/drivers/usb/host/ohci-nxp.c
> +++ b/drivers/usb/host/ohci-nxp.c
> @@ -43,16 +43,6 @@
>  #define USB_HOST_NEED_CLK_EN	(1 << 21)
>  #define PAD_CONTROL_LAST_DRIVEN	(1 << 19)
>  
> -#define USB_OTG_CLK_CTRL	IO_ADDRESS(USB_CONFIG_BASE + 0xFF4)
> -#define USB_OTG_CLK_STAT	IO_ADDRESS(USB_CONFIG_BASE + 0xFF8)
> -
> -/* USB_OTG_CLK_CTRL bit defines */
> -#define AHB_M_CLOCK_ON		(1 << 4)
> -#define OTG_CLOCK_ON		(1 << 3)
> -#define I2C_CLOCK_ON		(1 << 2)
> -#define DEV_CLOCK_ON		(1 << 1)
> -#define HOST_CLOCK_ON		(1 << 0)
> -
>  #define USB_OTG_STAT_CONTROL	IO_ADDRESS(USB_CONFIG_BASE + 0x110)
>  
>  /* USB_OTG_STAT_CONTROL bit defines */
> @@ -72,7 +62,9 @@ static struct i2c_client *isp1301_i2c_client;
>  
>  extern int usb_disabled(void);
>  
> -static struct clk *usb_clk;
> +static struct clk *usb_pll_clk;
> +static struct clk *usb_dev_clk;
> +static struct clk *usb_otg_clk;
>  
>  static void isp1301_configure_pnx4008(void)
>  {
> @@ -249,8 +241,6 @@ static const struct hc_driver ohci_nxp_hc_driver = {
>  	.start_port_reset = ohci_start_port_reset,
>  };
>  
> -#define USB_CLOCK_MASK (AHB_M_CLOCK_ON| OTG_CLOCK_ON | HOST_CLOCK_ON | I2C_CLOCK_ON)
> -
>  static void nxp_set_usb_bits(void)
>  {
>  	if (machine_is_pnx4008()) {
> @@ -327,41 +317,63 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
>  	/* Enable AHB slave USB clock, needed for further USB clock control */
>  	__raw_writel(USB_SLAVE_HCLK_EN | PAD_CONTROL_LAST_DRIVEN, USB_CTRL);
>  
> -	isp1301_configure();
> -
>  	/* Enable USB PLL */
> -	usb_clk = clk_get(&pdev->dev, "ck_pll5");
> -	if (IS_ERR(usb_clk)) {
> +	usb_pll_clk = clk_get(&pdev->dev, "ck_pll5");
> +	if (IS_ERR(usb_pll_clk)) {
>  		dev_err(&pdev->dev, "failed to acquire USB PLL\n");
> -		ret = PTR_ERR(usb_clk);
> +		ret = PTR_ERR(usb_pll_clk);
>  		goto out1;
>  	}
>  
> -	ret = clk_enable(usb_clk);
> +	ret = clk_enable(usb_pll_clk);
>  	if (ret < 0) {
>  		dev_err(&pdev->dev, "failed to start USB PLL\n");
>  		goto out2;
>  	}
>  
> -	ret = clk_set_rate(usb_clk, 48000);
> +	ret = clk_set_rate(usb_pll_clk, 48000);
>  	if (ret < 0) {
>  		dev_err(&pdev->dev, "failed to set USB clock rate\n");
>  		goto out3;
>  	}
>  
> +	/* Enable USB device clock */
> +	usb_dev_clk = clk_get(&pdev->dev, "ck_usbd");
> +	if (IS_ERR(usb_dev_clk)) {
> +		dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
> +		ret = PTR_ERR(usb_dev_clk);
> +		goto out4;
> +	}
> +
> +	ret = clk_enable(usb_dev_clk);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
> +		goto out5;
> +	}
> +
> +	/* Enable USB otg clocks */
> +	usb_otg_clk = clk_get(&pdev->dev, "ck_usb_otg");
> +	if (IS_ERR(usb_otg_clk)) {
> +		dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
> +		ret = PTR_ERR(usb_dev_clk);
> +		goto out6;
> +	}
> +
>  	__raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL);
>  
> -	/* Set to enable all needed USB clocks */
> -	__raw_writel(USB_CLOCK_MASK, USB_OTG_CLK_CTRL);
> +	ret = clk_enable(usb_otg_clk);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
> +		goto out7;
> +	}
>  
> -	while ((__raw_readl(USB_OTG_CLK_STAT) & USB_CLOCK_MASK) !=
> -	       USB_CLOCK_MASK) ;
> +	isp1301_configure();
>  
>  	hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
>  	if (!hcd) {
>  		dev_err(&pdev->dev, "Failed to allocate HC buffer\n");
>  		ret = -ENOMEM;
> -		goto out3;
> +		goto out8;
>  	}
>  
>  	/* Set all USB bits in the Start Enable register */
> @@ -371,14 +383,14 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
>  	if (!res) {
>  		dev_err(&pdev->dev, "Failed to get MEM resource\n");
>  		ret =  -ENOMEM;
> -		goto out4;
> +		goto out8;
>  	}
>  
>  	hcd->regs = devm_request_and_ioremap(&pdev->dev, res);
>  	if (!hcd->regs) {
>  		dev_err(&pdev->dev, "Failed to devm_request_and_ioremap\n");
>  		ret =  -ENOMEM;
> -		goto out4;
> +		goto out8;
>  	}
>  	hcd->rsrc_start = res->start;
>  	hcd->rsrc_len = resource_size(res);
> @@ -386,7 +398,7 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
>  	irq = platform_get_irq(pdev, 0);
>  	if (irq < 0) {
>  		ret = -ENXIO;
> -		goto out4;
> +		goto out8;
>  	}
>  
>  	nxp_start_hc();
> @@ -400,13 +412,21 @@ static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
>  		return ret;
>  
>  	nxp_stop_hc();
> -out4:
> +out8:
>  	nxp_unset_usb_bits();
>  	usb_put_hcd(hcd);
> +out7:
> +	clk_disable(usb_otg_clk);
> +out6:
> +	clk_put(usb_otg_clk);
> +out5:
> +	clk_disable(usb_dev_clk);
> +out4:
> +	clk_put(usb_dev_clk);
>  out3:
> -	clk_disable(usb_clk);
> +	clk_disable(usb_pll_clk);
>  out2:
> -	clk_put(usb_clk);
> +	clk_put(usb_pll_clk);
>  out1:
>  	isp1301_i2c_client = NULL;
>  out:
> @@ -422,8 +442,10 @@ static int usb_hcd_nxp_remove(struct platform_device *pdev)
>  	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
>  	usb_put_hcd(hcd);
>  	nxp_unset_usb_bits();
> -	clk_disable(usb_clk);
> -	clk_put(usb_clk);
> +	clk_disable(usb_pll_clk);
> +	clk_put(usb_pll_clk);
> +	clk_disable(usb_dev_clk);
> +	clk_put(usb_dev_clk);
>  	i2c_unregister_device(isp1301_i2c_client);
>  	isp1301_i2c_client = NULL;
>  

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/