[PATCH 4/5] platform-x86: intel_mid_thermal: convert to use IntelMSIC API
From: Alan Cox
Date: Thu Jan 26 2012 - 12:26:02 EST
From: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Intel MSIC MFD driver provides common register access interface to the
devices in the MSIC die so we use that instead of SCU IPC.
Signed-off-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@xxxxxxxxxxxxxxx>
Signed-off-by: Alan Cox <alan@xxxxxxxxxxxxxxx>
---
drivers/platform/x86/Kconfig | 2 +-
drivers/platform/x86/intel_mid_thermal.c | 39 ++++++++++++++----------------
2 files changed, 19 insertions(+), 22 deletions(-)
diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 5715e4d..86720bc 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -672,7 +672,7 @@ config INTEL_MID_POWER_BUTTON
config INTEL_MFLD_THERMAL
tristate "Thermal driver for Intel Medfield platform"
- depends on INTEL_SCU_IPC && THERMAL
+ depends on MFD_INTEL_MSIC && THERMAL
help
Say Y here to enable thermal driver support for the Intel Medfield
platform.
diff --git a/drivers/platform/x86/intel_mid_thermal.c b/drivers/platform/x86/intel_mid_thermal.c
index de2e62e..aef4979 100644
--- a/drivers/platform/x86/intel_mid_thermal.c
+++ b/drivers/platform/x86/intel_mid_thermal.c
@@ -33,18 +33,15 @@
#include <linux/slab.h>
#include <linux/pm.h>
#include <linux/thermal.h>
-
-#include <asm/intel_scu_ipc.h>
+#include <linux/mfd/intel_msic.h>
/* Number of thermal sensors */
#define MSIC_THERMAL_SENSORS 4
/* ADC1 - thermal registers */
-#define MSIC_THERM_ADC1CNTL1 0x1C0
#define MSIC_ADC_ENBL 0x10
#define MSIC_ADC_START 0x08
-#define MSIC_THERM_ADC1CNTL3 0x1C2
#define MSIC_ADCTHERM_ENBL 0x04
#define MSIC_ADCRRDATA_ENBL 0x05
#define MSIC_CHANL_MASK_VAL 0x0F
@@ -75,8 +72,8 @@
#define ADC_VAL60C 315
/* ADC base addresses */
-#define ADC_CHNL_START_ADDR 0x1C5 /* increments by 1 */
-#define ADC_DATA_START_ADDR 0x1D4 /* increments by 2 */
+#define ADC_CHNL_START_ADDR INTEL_MSIC_ADC1ADDR0 /* increments by 1 */
+#define ADC_DATA_START_ADDR INTEL_MSIC_ADC1SNS0H /* increments by 2 */
/* MSIC die attributes */
#define MSIC_DIE_ADC_MIN 488
@@ -189,17 +186,17 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
addr = td_info->chnl_addr;
/* Enable the msic for conversion before reading */
- ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
+ ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCRRDATA_ENBL);
if (ret)
return ret;
/* Re-toggle the RRDATARD bit (temporary workaround) */
- ret = intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
+ ret = intel_msic_reg_write(INTEL_MSIC_ADC1CNTL3, MSIC_ADCTHERM_ENBL);
if (ret)
return ret;
/* Read the higher bits of data */
- ret = intel_scu_ipc_ioread8(addr, &data);
+ ret = intel_msic_reg_read(addr, &data);
if (ret)
return ret;
@@ -207,7 +204,7 @@ static int mid_read_temp(struct thermal_zone_device *tzd, unsigned long *temp)
adc_val = (data << 2);
addr++;
- ret = intel_scu_ipc_ioread8(addr, &data);/* Read lower bits */
+ ret = intel_msic_reg_read(addr, &data);/* Read lower bits */
if (ret)
return ret;
@@ -235,7 +232,7 @@ static int configure_adc(int val)
int ret;
uint8_t data;
- ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+ ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
if (ret)
return ret;
@@ -246,7 +243,7 @@ static int configure_adc(int val)
/* Just stop the ADC */
data &= (~MSIC_ADC_START);
}
- return intel_scu_ipc_iowrite8(MSIC_THERM_ADC1CNTL1, data);
+ return intel_msic_reg_write(INTEL_MSIC_ADC1CNTL1, data);
}
/**
@@ -262,21 +259,21 @@ static int set_up_therm_channel(u16 base_addr)
int ret;
/* Enable all the sensor channels */
- ret = intel_scu_ipc_iowrite8(base_addr, SKIN_SENSOR0_CODE);
+ ret = intel_msic_reg_write(base_addr, SKIN_SENSOR0_CODE);
if (ret)
return ret;
- ret = intel_scu_ipc_iowrite8(base_addr + 1, SKIN_SENSOR1_CODE);
+ ret = intel_msic_reg_write(base_addr + 1, SKIN_SENSOR1_CODE);
if (ret)
return ret;
- ret = intel_scu_ipc_iowrite8(base_addr + 2, SYS_SENSOR_CODE);
+ ret = intel_msic_reg_write(base_addr + 2, SYS_SENSOR_CODE);
if (ret)
return ret;
/* Since this is the last channel, set the stop bit
* to 1 by ORing the DIE_SENSOR_CODE with 0x10 */
- ret = intel_scu_ipc_iowrite8(base_addr + 3,
+ ret = intel_msic_reg_write(base_addr + 3,
(MSIC_DIE_SENSOR_CODE | 0x10));
if (ret)
return ret;
@@ -295,11 +292,11 @@ static int reset_stopbit(uint16_t addr)
{
int ret;
uint8_t data;
- ret = intel_scu_ipc_ioread8(addr, &data);
+ ret = intel_msic_reg_read(addr, &data);
if (ret)
return ret;
/* Set the stop bit to zero */
- return intel_scu_ipc_iowrite8(addr, (data & 0xEF));
+ return intel_msic_reg_write(addr, (data & 0xEF));
}
/**
@@ -322,7 +319,7 @@ static int find_free_channel(void)
uint8_t data;
/* check whether ADC is enabled */
- ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL1, &data);
+ ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL1, &data);
if (ret)
return ret;
@@ -331,7 +328,7 @@ static int find_free_channel(void)
/* ADC is already enabled; Looking for an empty channel */
for (i = 0; i < ADC_CHANLS_MAX; i++) {
- ret = intel_scu_ipc_ioread8(ADC_CHNL_START_ADDR + i, &data);
+ ret = intel_msic_reg_read(ADC_CHNL_START_ADDR + i, &data);
if (ret)
return ret;
@@ -359,7 +356,7 @@ static int mid_initialize_adc(struct device *dev)
* Ensure that adctherm is disabled before we
* initialize the ADC
*/
- ret = intel_scu_ipc_ioread8(MSIC_THERM_ADC1CNTL3, &data);
+ ret = intel_msic_reg_read(INTEL_MSIC_ADC1CNTL3, &data);
if (ret)
return ret;
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/