Re: [PATCH] DMAEngine: Define generic transfer request api

[Jassi Brar]

On 16 August 2011 18:26, Koul, Vinod <vinod.koul@xxxxxxxxx> wrote:
> On Fri, 2011-08-12 at 16:44 +0530, Jassi Brar wrote:
>> Define a new api that could be used for doing fancy data transfers
>> like interleaved to contiguous copy and vice-versa.
>> Traditional SG_list based transfers tend to be very inefficient in
>> such cases as where the interleave and chunk are only a few bytes,
>> which call for a very condensed api to convey pattern of the transfer.
>>
>> This api supports all 4 variants of scatter-gather and contiguous transfer.
>> Besides, it could also represent common operations like
>>         device_prep_dma_{cyclic, memset, memcpy}
>> and maybe some more that I am not sure of.
>>
>> Of course, neither can this api help transfers that don't lend to DMA by
>> nature, i.e, scattered tiny read/writes with no periodic pattern.
>>
>> Signed-off-by: Jassi Brar <jaswinder.singh@xxxxxxxxxx>
>> ---
>>  include/linux/dmaengine.h |   73 +++++++++++++++++++++++++++++++++++++++++++++
>>  1 files changed, 73 insertions(+), 0 deletions(-)
>>
>> diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h
>> index 8fbf40e..74f3ae0 100644
>> --- a/include/linux/dmaengine.h
>> +++ b/include/linux/dmaengine.h
>> @@ -76,6 +76,76 @@ enum dma_transaction_type {
>>  /* last transaction type for creation of the capabilities mask */
>>  #define DMA_TX_TYPE_END (DMA_CYCLIC + 1)
>>
>> +/**
>> + * Generic Transfer Request
>> + * ------------------------
>> + * A chunk is collection of contiguous bytes to be transfered.
>> + * The gap(in bytes) between two chunks is called inter-chunk-gap(ICG).
>> + * ICGs may or maynot change between chunks.
>> + * A FRAME is the smallest series of contiguous {chunk,icg} pairs,
>> + *  that when repeated an integral number of times, specifies the transfer.
>> + * A transfer template is specification of a Frame, the number of times
>> + *  it is to be repeated and other per-transfer attributes.
>> + *
>> + * Practically, a client driver would have ready a template for each
>> + *  type of transfer it is going to need during its lifetime and
>> + *  set only 'src_start' and 'dst_start' before submitting the requests.
>> + *
>> + *
>> + *  |      Frame-1        |       Frame-2       | ~ |       Frame-'numf'  |
>> + *  |====....==.===...=...|====....==.===...=...| ~ |====....==.===...=...|
>> + *
>> + *    ==  Chunk size
>> + *    ... ICG
>> + */
>> +
>> +/**
>> + * struct data_chunk - Element of scatter-gather list that makes a frame.
>> + * @size: Number of bytes to read from source.
>> + *     size_dst := fn(op, size_src), so doesn't mean much for destination.
>> + * @icg: Number of bytes to jump after last src/dst address of this
>> + *    chunk and before first src/dst address for next chunk.
>> + *    Ignored for dst(assumed 0), if dst_inc is true and dst_sgl is false.
>> + *    Ignored for src(assumed 0), if src_inc is true and src_sgl is false.
>> + */
>> +struct data_chunk {
>> +     size_t size;
>> +     size_t icg;
>> +};
>> +
>> +/**
>> + * struct xfer_template - Template to convey DMAC the transfer pattern
>> + *    and attributes.
>> + * @op: The operation to perform on source data before writing it on
>> + *    to destination address.
>> + * @src_start: Bus address of source for the first chunk.
>> + * @dst_start: Bus address of destination for the first chunk.
>> + * @src_inc: If the source address increments after reading from it.
>> + * @dst_inc: If the destination address increments after writing to it.
>> + * @src_sgl: If the 'icg' of sgl[] applies to Source (scattered read).
>> + *           Otherwise, source is read contiguously (icg ignored).
>> + *           Ignored if src_inc is false.
>> + * @dst_sgl: If the 'icg' of sgl[] applies to Destination (scattered write).
>> + *           Otherwise, destination is filled contiguously (icg ignored).
>> + *           Ignored if dst_inc is false.
>> + * @frm_irq: If the client expects DMAC driver to do callback after each frame.
>> + * @numf: Number of frames in this template.
>> + * @frame_size: Number of chunks in a frame i.e, size of sgl[].
>> + * @sgl: Array of {chunk,icg} pairs that make up a frame.
>> + */
>> +struct xfer_template {
>> +     enum dma_transaction_type op;
>> +     dma_addr_t src_start;
>> +     dma_addr_t dst_start;
>> +     bool src_inc;
>> +     bool dst_inc;
>> +     bool src_sgl;
>> +     bool dst_sgl;
>> +     bool frm_irq;
>> +     size_t numf;
>> +     size_t frame_size;
>> +     struct data_chunk sgl[0];
>> +};
>>
>>  /**
>>   * enum dma_ctrl_flags - DMA flags to augment operation preparation,
>> @@ -432,6 +502,7 @@ struct dma_tx_state {
>>   * @device_prep_dma_cyclic: prepare a cyclic dma operation suitable for audio.
>>   *   The function takes a buffer of size buf_len. The callback function will
>>   *   be called after period_len bytes have been transferred.
>> + * @device_prep_dma_genxfer: Transfer expression in a generic way.
>>   * @device_control: manipulate all pending operations on a channel, returns
>>   *   zero or error code
>>   * @device_tx_status: poll for transaction completion, the optional
>> @@ -496,6 +567,8 @@ struct dma_device {
>>       struct dma_async_tx_descriptor *(*device_prep_dma_cyclic)(
>>               struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len,
>>               size_t period_len, enum dma_data_direction direction);
>> +     struct dma_async_tx_descriptor *(*device_prep_dma_genxfer)(
>> +             struct dma_chan *chan, struct xfer_template *xt);
>>       int (*device_control)(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
>>               unsigned long arg);
>>
> Do you have a driver which is using the API, would help to evaluate this
> API when we see the usage :)
Sorry, not in public and not for DMAENGINE.
It will help if you see it as a generic[1] solution to the requirement of
supporting interleaved transfers with DMACs like TI's EDMA, SDMA,
ARM's PL330 and many more in future.

> Currently we have two approaches to solve this problem first being the
> DMA_STRIDE_CONFIG proposed by Linus W, I feel this one is better
> approach as this can give client ability to configure each transfer
> rather than set for the channel.
To me, doing it via a control command vs new transfer type, is secondary
to doing it in a generic way. And yes, I too believe this way is better because
it is more flexible.


[1] Btw, I haven't yet added option to specify byte/half-word/word swap
while data transfer - which I once had to do with PL330 in a weird setup.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/