Re: [PATCH v2 01/13] mfd: pruss mfd driver.

From: Samuel Ortiz
Date: Tue Feb 22 2011 - 06:33:39 EST


On Tue, Feb 22, 2011 at 11:48:51AM +0100, Wolfgang Grandegger wrote:
> On 02/22/2011 11:31 AM, Samuel Ortiz wrote:
> > Hi Subhasish,
> >
> > On Tue, Feb 22, 2011 at 11:13:38AM +0530, Subhasish Ghosh wrote:
> >> Thank you for your comments.
> > No problem.
> >
> >>>> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> >>>> index fd01836..6c437df 100644
> >>>> --- a/drivers/mfd/Kconfig
> >>>> +++ b/drivers/mfd/Kconfig
> >>>> @@ -81,6 +81,16 @@ config MFD_DM355EVM_MSP
> >>>> boards. MSP430 firmware manages resets and power sequencing,
> >>>> inputs from buttons and the IR remote, LEDs, an RTC, and more.
> >>>>
> >>>> +config MFD_DA8XX_PRUSS
> >>>> + tristate "Texas Instruments DA8XX PRUSS support"
> >>>> + depends on ARCH_DAVINCI && ARCH_DAVINCI_DA850
> >>> Why are we depending on those ?
> >>
> >> SG -- The PRUSS core in only available within DA850 and DA830,
> >> DA830 support is not yet implemented.
> > Sure, but if there are no actual code dependencies, I'd like to get rid of
> > those depends.
> >
> >>>> +u32 pruss_disable(struct device *dev, u8 pruss_num)
> >>>> +{
> >>>> + struct da8xx_pruss *pruss = dev_get_drvdata(dev->parent);
> >>>> + da8xx_prusscore_regs h_pruss;
> >>>> + u32 temp_reg;
> >>>> +
> >>>> + if (pruss_num == DA8XX_PRUCORE_0) {
> >>>> + /* Disable PRU0 */
> >>>> + h_pruss = (da8xx_prusscore_regs)
> >>>> + ((u32) pruss->ioaddr + 0x7000);
> >>> So it seems you're doing this in several places, and I have a few
> >>> comments:
> >>>
> >>> - You don't need the da8xx_prusscore_regs at all.
> >>> - Define the register map through a set of #define in your header file.
> >>> - Use a static routine that takes the core number and returns the
> >>> register map
> >>> offset.
> >>>
> >>> Then routines like this one will look a lot more readable.
> >>
> >> SG -- There are a huge number of PRUSS registers. A lot of them are
> >> reserved and are expected to change as development on the
> >> controller is still ongoing.
> > First of all, from what I read in your patch you're only using the CONTROL
> > offset.
> >
> >> If we use #defines to plot
> >> all the registers, then first, there are too many array type
> >> registers which will need to be duplicated.
> > What I'm expecting is a small set of defines for the register offsets. You
> > have 13 fields in your da8xx_prusscore_regs, you only need to define 13
> > register offsets.
> >
> > So, if you have a:
> >
> > static u32 reg_offset(struct device *dev, u8 pru_num)
> > {
> > struct da8xx_pruss *pru = dev_get_drvdata(dev->parent);
> >
> > switch (pru_num) {
> > case DA8XX_PRUCORE_0:
> > return (u32) pru->ioaddr + 0x7000;
> > case DA8XX_PRUCORE_1:
> > return (u32) pru->ioaddr + 0x7800;
> > default:
> > return 0;
> > }
> >
> >
> > then routines like pruss_enable (which should return an int, btw) would look
> > like:
> >
> > int pruss_enable(struct device *dev, u8 pruss_num)
> > {
> > u32 offset = reg_offset(dev, pruss_num);
> >
> > if (offset == 0)
> > return -EINVAL;
> >
> > __raw_writel(DA8XX_PRUCORE_CONTROL_RESETVAL,
> > offset + PRU_CORE_CONTROL);
> >
> > return 0;
> > }
>
> All registers are memory mapped and could nicely be described by
> structures (and sub-structures). Therefore we asked to considerer
> structs, at least for the Pruss SocketCAN drivers.
>
> That would result in
> much much clearer and better readable code. The code above would shrink to:
>
> __raw_writel(DA8XX_PRUCORE_CONTROL_RESETVAL,
> &prucore[pruss_num].control);
This driver seems to exclusively use the control offset, which is why I don't
see an absolute need for doing this mapping.
But if both maps are contiguous then doing the mapping would prevent us from
calling reg_offset() and would bring some advantage. I'd then be fine with it.
For now, da8xx_prusscore_regs seems to be larger than the 0x800 interval
between the 2 maps, so I have no idea if both maps are indeed contiguous.

Cheers,
Samuel.

--
Intel Open Source Technology Centre
http://oss.intel.com/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/