Re: [PATCH v3] EHCI bus glue for on-chip PMC MSP USB controller.

[Anoop P A]

On Fri, 2011-02-04 at 11:56 -0800, Greg KH wrote:
> On Thu, Jan 27, 2011 at 04:58:56PM +0530, Anoop P.A wrote:
> > From: Anoop P A <anoop.pa@xxxxxxxxx>
> > 
> > Signed-off-by: Anoop P A <anoop.pa@xxxxxxxxx>
> > Tested-by: Shane McDonald <mcdonald.shane@xxxxxxxxx>
> 
> Care to provide a "real" changelog comment for this patch?  We need
> something here.
Will do.

> 
> > ---
> >  drivers/usb/host/Kconfig       |   15 +-

> > + * PMC MSP EHCI (Host Controller Driver) for USB.
> > + *
> > + * (C) Copyright 2006-2010 PMC-Sierra Inc
> > + *
> > + * This program is free software; you can redistribute  it and/or modify it
> > + * under  the terms of  the GNU General  Public License as published by the
> > + * Free Software Foundation;  either version 2 of the  License, or (at your
> > + * option) any later version.
> 
> Are you sure about "any later version"?  Is this acceptable to your
> company lawyers?
> 
Will fix it. 

> > + *
> > + * THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
> > + * WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
> > + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
> > + * NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
> > + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
> > + * NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
> > + * USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
> > + * ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
> > + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
> > + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> > + *
> > + * You should have received a copy of the  GNU General Public License along
> > + * with this program; if not, write  to the Free Software Foundation, Inc.,
> > + * 675 Mass Ave, Cambridge, MA 02139, USA.
> 
> These two paragraphs are not needed, please remove them.
> 
Ok.


> > + */
> > +
> > +#include <linux/platform_device.h>
> > +#include <linux/gpio.h>
> > +#include <msp_usb.h>
> > +
> > +/* includes */
> 
> Um, includes for what?  Are we writing comments for the previous lines?
> 
> > +#define USB_CTRL_MODE_HOST		0x3
> > +					/* host mode */
> > +#define USB_CTRL_MODE_BIG_ENDIAN	0x4
> > +					/* big endian */
> > +#define USB_CTRL_MODE_STREAM_DISABLE	0x10
> > +					/* stream disable*/
> > +#define USB_CTRL_FIFO_THRESH		0x00300000
> > +					/* thresh hold */
> > +#define USB_EHCI_REG_USB_MODE		0x68
> > +					/* register offset for usb_mode */
> > +#define USB_EHCI_REG_USB_FIFO		0x24
> > +					/* register offset for usb fifo */
> > +#define USB_EHCI_REG_USB_STATUS		0x44
> > +					/* register offset for usb status */
> > +#define USB_EHCI_REG_BIT_STAT_STS	(1<<29)
> > +					/* serial/parallel transceiver */
> > +#define MSP_PIN_USB0_HOST_DEV		49
> > +					/* TWI USB0 host device pin */
> > +#define MSP_PIN_USB1_HOST_DEV		50
> > +					/* TWI USB1 host device pin */
> 
> Ok, I see we are.  That's horrible, please fix it up.

Ok. 

> 
> > +
> > +extern int usb_disabled(void);
> 
> Why is this in a .c file?  externs should never be in a .c file.
> 
Ok 

> 
> > +
> > +void usb_hcd_tdi_set_mode(struct ehci_hcd *ehci)
> > +{
> > +	u8 *base;
> > +	u8 *statreg;
> > +	u8 *fiforeg;
> > +	u32 val;
> > +	struct ehci_regs *reg_base = ehci->regs;
> > +
> > +	/* get register base */
> > +	base = (u8 *)reg_base + USB_EHCI_REG_USB_MODE;
> > +	statreg = (u8 *)reg_base + USB_EHCI_REG_USB_STATUS;
> > +	fiforeg = (u8 *)reg_base + USB_EHCI_REG_USB_FIFO;
> > +
> > +	/* set the controller to host mode and BIG ENDIAN */
> > +	ehci_writel(ehci, (USB_CTRL_MODE_HOST | USB_CTRL_MODE_BIG_ENDIAN
> > +		| USB_CTRL_MODE_STREAM_DISABLE), (u32 *)base);
> > +
> > +	/* clear STS to select parallel transceiver interface */
> > +	val = ehci_readl(ehci, (u32 *)statreg);
> > +	val = val & ~USB_EHCI_REG_BIT_STAT_STS;
> > +	ehci_writel(ehci, val, (u32 *)statreg);
> > +
> > +	/* write to set the proper fifo threshold */
> > +	ehci_writel(ehci, USB_CTRL_FIFO_THRESH, (u32 *)fiforeg);
> > +
> > +	/* set TWI GPIO USB_HOST_DEV pin high */
> > +	gpio_direction_output(MSP_PIN_USB0_HOST_DEV, 1);
> > +#ifdef CONFIG_MSP_HAS_DUAL_USB
> > +	gpio_direction_output(MSP_PIN_USB1_HOST_DEV, 1);
> > +#endif
> 
> Please don't put #defines in .c files.
You mean #ifdef ???

> 
> > +}
> > +
> > +/* called after powerup, by probe or system-pm "wakeup" */
> > +static int ehci_msp_reinit(struct ehci_hcd *ehci)
> > +{
> > +	ehci_port_power(ehci, 0);
> > +
> > +	return 0;
> > +}
> > +
> > +/* called during probe() after chip reset completes */
> > +static int ehci_msp_setup(struct usb_hcd *hcd)
> > +{
> > +	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);
> > +	u32			temp;
> > +	int			retval;
> > +	ehci->big_endian_mmio = 1;
> > +	ehci->big_endian_desc = 1;
> > +	ehci->pmc_msp_tdi = 1;
> > +
> > +	ehci->caps = hcd->regs;
> > +	ehci->regs = hcd->regs +
> > +			HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
> > +	dbg_hcs_params(ehci, "reset");
> > +	dbg_hcc_params(ehci, "reset");
> > +
> > +	/* cache this readonly data; minimize chip reads */
> > +	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
> > +	hcd->has_tt = 1;
> > +	tdi_reset(ehci);
> > +
> > +	retval = ehci_halt(ehci);
> > +	if (retval)
> > +		return retval;
> > +
> > +	ehci_reset(ehci);
> > +
> > +	/* data structure init */
> > +	retval = ehci_init(hcd);
> > +	if (retval)
> > +		return retval;
> > +
> > +	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
> > +	temp &= 0x0f;
> > +	if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
> > +		ehci_dbg(ehci, "bogus port configuration: "
> > +			"cc=%d x pcc=%d < ports=%d\n",
> > +			HCS_N_CC(ehci->hcs_params),
> > +			HCS_N_PCC(ehci->hcs_params),
> > +			HCS_N_PORTS(ehci->hcs_params));
> > +	}
> > +
> > +	retval = ehci_msp_reinit(ehci);
> > +
> > +	return retval;
> > +}
> > +
> > +/*-------------------------------------------------------------------------*/
> > +
> > +static void msp_start_hc(struct platform_device *dev)
> > +{
> > +	printk(KERN_DEBUG __FILE__
> > +		   ": starting PMC MSP EHCI USB Controller\n");
> 
> Why?  Who really cares?  And, if you _really_ want to do this, please
> use a dev_dbg() call instead, which ties it properly into the dynamic
> printk system _and_ properly identifies this deivce.

OK.

> 
> > +
> > +	/*
> > +	 * Now, carefully enable the USB clock, and take
> > +	 * the USB host controller out of reset.
> > +	 */
> > +	printk(KERN_DEBUG __FILE__
> > +			": Clock to USB host has been enabled\n");
> > +}
> 
> 
> You never enabled anything, yet you said you did?  Somethings wrong
> here.
Forget to remove those comments. 

> 
> > +
> > +static void msp_stop_hc(struct platform_device *dev)
> > +{
> > +	printk(KERN_DEBUG __FILE__
> > +		   ": stopping PMC MSP EHCI USB Controller\n");
> > +}
> 
> Same for this printk, you didn't stop anything.
> 
> Also fix it up and don't use printk, see above.

Ok.
> 
> > +
> > +
> > +/*-------------------------------------------------------------------------*/
> > +
> > +/*-------------------------------------------------------------------------*/
> > +
> > +#ifdef	CONFIG_PM
> > +
> > +/* suspend/resume, section 4.3 */
> > +
> > +/* These routines rely on the bus glue
> > + * to handle powerdown and wakeup, and currently also on
> > + * transceivers that don't need any software attention to set up
> > + * the right sort of wakeup.
> > + * Also they depend on separate root hub suspend/resume.
> > + */
> > +static int ehci_msp_suspend(struct device *dev)
> > +{
> > +	struct usb_hcd *hcd = dev_get_drvdata(dev);
> > +	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
> > +	unsigned long flags;
> > +	int rc;
> > +
> > +	return 0;
> > +	rc = 0;
> > +
> > +	if (time_before(jiffies, ehci->next_statechange))
> > +		msleep(10);
> 
> Short sleep, why?
I am not very sure. Person who originally wrote this driver is
unreachable.Any potential issues??
> 
> > +
> > +	/* Root hub was already suspended. Disable irq emission and
> > +	 * mark HW unaccessible.  The PM and USB cores make sure that
> > +	 * the root hub is either suspended or stopped.
> > +	 */
> > +	spin_lock_irqsave(&ehci->lock, flags);
> > +	ehci_prepare_ports_for_controller_suspend(ehci, device_may_wakeup(dev));
> > +	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
> > +	(void)ehci_readl(ehci, &ehci->regs->intr_enable);
> > +
> > +	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
> > +	spin_unlock_irqrestore(&ehci->lock, flags);
> > +
> > +	/* could save FLADJ in case of Vaux power loss
> > +	... we'd only use it to handle clock skew */
> 
> Huh?
Looks like some comments missed while cleaning up
> 
> > +
> > +	return rc;
> > +}
> > +
> > +static int ehci_msp_resume(struct device *dev)
> > +{
> > +	struct usb_hcd *hcd = dev_get_drvdata(dev);
> > +	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
> > +
> > +
> > +	/* maybe restore FLADJ */
> 
> Don't you know?
Not really :)
 
> 
> > +
> > +	if (time_before(jiffies, ehci->next_statechange))
> > +		msleep(100);
> 
> That's a long sleep, are you sure that's ok on the resume path?
> 
Again any potential issue you can guess ?

> > +
> > +	/* Mark hardware accessible again as we are out of D3 state by now */
> > +	set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
> > +
> > +	/* If CF is still set, we maintained PCI Vaux power.
> > +	 * Just undo the effect of ehci_pci_suspend().
> > +	 */
> > +	if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF) {
> > +		int	mask = INTR_MASK;
> > +
> > +		ehci_prepare_ports_for_controller_resume(ehci);
> > +		if (!hcd->self.root_hub->do_remote_wakeup)
> > +			mask &= ~STS_PCD;
> > +		ehci_writel(ehci, mask, &ehci->regs->intr_enable);
> > +		ehci_readl(ehci, &ehci->regs->intr_enable);
> > +		return 0;
> > +	}
> > +
> > +	ehci_dbg(ehci, "lost power, restarting\n");
> > +	usb_root_hub_lost_power(hcd->self.root_hub);
> > +
> > +	/* Else reset, to cope with power loss or flush-to-storage
> > +	 * style "resume" having let BIOS kick in during reboot.
> > +	 */
> > +	(void) ehci_halt(ehci);
> > +	(void) ehci_reset(ehci);
> > +	(void) ehci_msp_reinit(ehci);
> > +
> > +	/* emptying the schedule aborts any urbs */
> > +	spin_lock_irq(&ehci->lock);
> > +	if (ehci->reclaim)
> > +		end_unlink_async(ehci);
> > +	ehci_work(ehci);
> > +	spin_unlock_irq(&ehci->lock);
> > +
> > +	ehci_writel(ehci, ehci->command, &ehci->regs->command);
> > +	ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
> > +	ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
> > +
> > +	/* here we "know" root ports should always stay powered */
> > +	ehci_port_power(ehci, 1);
> > +
> > +	hcd->state = HC_STATE_SUSPENDED;
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct dev_pm_ops ehci_msp_pmops = {
> > +	.suspend	= ehci_msp_suspend,
> > +	.resume		= ehci_msp_resume,
> > +};
> > +#endif
> > +
> > +
> > +/* configure so an HC device and id are always provided */
> > +/* always called with process context; sleeping is OK */
> > +
> > +static int usb_hcd_msp_map_regs(struct mspusb_device *dev)
> > +{
> > +	struct resource *res;
> > +	struct platform_device *pdev = &dev->dev;
> > +	u32 res_len;
> > +	int retval;
> > +
> > +	/* MAB register space */
> > +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > +	if (res == NULL)
> > +		return -ENOMEM;
> > +	res_len = res->end - res->start + 1;
> > +	if (!request_mem_region(res->start, res_len, "mab regs"))
> > +		return -EBUSY;
> > +
> > +	dev->mab_regs = ioremap_nocache(res->start, res_len);
> > +	if (dev->mab_regs == NULL) {
> > +		retval = -ENOMEM;
> > +		goto err1;
> > +	}
> > +
> > +	/* MSP USB register space */
> > +	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> > +	if (res == NULL) {
> > +		retval = -ENOMEM;
> > +		goto err2;
> > +	}
> > +	res_len = res->end - res->start + 1;
> > +	if (!request_mem_region(res->start, res_len, "usbid regs")) {
> > +		retval = -EBUSY;
> > +		goto err2;
> > +	}
> > +	dev->usbid_regs = ioremap_nocache(res->start, res_len);
> > +	if (dev->usbid_regs == NULL) {
> > +		retval = -ENOMEM;
> > +		goto err3;
> > +	}
> > +
> > +	return 0;
> > +err3:
> > +	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
> > +	res_len = res->end - res->start + 1;
> > +	release_mem_region(res->start, res_len);
> > +err2:
> > +	iounmap(dev->mab_regs);
> > +err1:
> > +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > +	res_len = res->end - res->start + 1;
> > +	release_mem_region(res->start, res_len);
> > +	dev_err(&pdev->dev, "Failed to map non-EHCI regs.\n");
> > +	return retval;
> > +}
> > +
> > +/**
> > + * usb_hcd_msp_probe - initialize PMC MSP-based HCDs
> > + * Context: !in_interrupt()
> > + *
> > + * Allocates basic resources for this USB host controller, and
> > + * then invokes the start() method for the HCD associated with it
> > + * through the hotplug entry's driver_data.
> > + *
> > + */
> > +int usb_hcd_msp_probe(const struct hc_driver *driver,
> > +			  struct platform_device *dev)
> > +{
> > +	int retval;
> > +	struct usb_hcd *hcd;
> > +	struct resource *res;
> > +	struct ehci_hcd		*ehci ;
> > +
> > +	hcd = usb_create_hcd(driver, &dev->dev, "pmcmsp");
> > +	if (!hcd)
> > +		return -ENOMEM;
> > +
> > +	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
> > +	if (res == NULL) {
> > +		pr_debug("No IOMEM resource info for %s.\n", dev->name);
> > +		retval = -ENOMEM;
> > +		goto err1;
> > +	}
> > +	hcd->rsrc_start = res->start;
> > +	hcd->rsrc_len = res->end - res->start + 1;
> > +	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, dev->name)) {
> > +		retval = -EBUSY;
> > +		goto err1;
> > +	}
> > +	hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len);
> > +	if (!hcd->regs) {
> > +		pr_debug("ioremap failed");
> > +		retval = -ENOMEM;
> > +		goto err2;
> > +	}
> > +	msp_start_hc(dev);
> > +
> > +	res = platform_get_resource(dev, IORESOURCE_IRQ, 0);
> > +	if (res == NULL) {
> > +		dev_err(&dev->dev, "No IRQ resource info for %s.\n", dev->name);
> > +		retval = -ENOMEM;
> > +		goto err3;
> > +	}
> > +
> > +	/* Map non-EHCI register spaces */
> > +	retval = usb_hcd_msp_map_regs(to_mspusb_device(dev));
> > +	if (retval != 0)
> > +		goto err3;
> > +
> > +	ehci = hcd_to_ehci(hcd);
> > +	ehci->big_endian_mmio = 1;
> > +	ehci->big_endian_desc = 1;
> > +
> > +
> > +	retval = usb_add_hcd(hcd, res->start, IRQF_SHARED);
> > +	if (retval == 0)
> > +		return 0;
> > +
> > +	usb_remove_hcd(hcd);
> > +err3:
> > +	msp_stop_hc(dev);
> > +	iounmap(hcd->regs);
> > +err2:
> > +	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
> > +err1:
> > +	usb_put_hcd(hcd);
> > +
> > +	return retval;
> > +}
> > +
> > +
> > +/* may be called without controller electrically present */
> > +/* may be called with controller, bus, and devices active */
> > +
> 
> What may be called?
may be usb_hcd_msp_remove :)
> 
> > +/**
> > + * usb_hcd_msp_remove - shutdown processing for PMC MSP-based HCDs
> > + * @dev: USB Host Controller being removed
> > + * Context: !in_interrupt()
> > + *
> > + * Reverses the effect of usb_hcd_msp_probe(), first invoking
> > + * the HCD's stop() method.  It is always called from a thread
> > + * context, normally "rmmod", "apmd", or something similar.
> > + *
> > + */
> > +void usb_hcd_msp_remove(struct usb_hcd *hcd, struct platform_device *dev)
> > +{
> > +	usb_remove_hcd(hcd);
> > +	msp_stop_hc(dev);
> > +	iounmap(hcd->regs);
> > +	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
> > +	usb_put_hcd(hcd);
> > +}
> > +
> > +#ifdef CONFIG_MSP_HAS_DUAL_USB
> > +/*-------------------------------------------------------------------------*/
> > +/*
> > + * Wrapper around the main ehci_irq.  Since both USB host controllers are
> > + * sharing the same IRQ, need to first determine whether we're the intended
> > + * recipient of this interrupt.
> > + */
> > +static irqreturn_t ehci_msp_irq(struct usb_hcd *hcd)
> > +{
> > +	u32 int_src;
> > +	struct device *dev = hcd->self.controller;
> > +	struct platform_device *pdev;
> > +	struct mspusb_device *mdev;
> > +	struct ehci_hcd	*ehci = hcd_to_ehci(hcd);
> > +
> > +	/* need to reverse-map a couple of containers to get our device */
> > +	pdev = to_platform_device(dev);
> > +	mdev = to_mspusb_device(pdev);
> > +
> > +	/* Check to see if this interrupt is for this host controller */
> > +	int_src = ehci_readl(ehci, &mdev->mab_regs->int_stat);
> > +	if (int_src & (1 << pdev->id))
> > +		return ehci_irq(hcd);
> > +
> > +	/* Not for this device */
> > +	return IRQ_NONE;
> > +}
> > +/*-------------------------------------------------------------------------*/
> > +#endif /* DUAL_USB */
> > +
> > +static const struct hc_driver ehci_msp_hc_driver = {
> > +	.description =		hcd_name,
> > +	.product_desc =		"PMC MSP EHCI",
> > +	.hcd_priv_size =	sizeof(struct ehci_hcd),
> > +
> > +	/*
> > +	 * generic hardware linkage
> > +	 */
> > +#ifdef CONFIG_MSP_HAS_DUAL_USB
> > +	.irq =			ehci_msp_irq,
> > +#else
> > +	.irq =			ehci_irq,
> > +#endif
> > +	.flags =		HCD_MEMORY | HCD_USB2,
> > +
> > +	/*
> > +	 * basic lifecycle operations
> > +	 */
> > +	.reset =		ehci_msp_setup,
> > +	.start =		ehci_run,
> > +	.shutdown		= ehci_shutdown,
> > +	.start			= ehci_run,
> > +	.stop			= ehci_stop,
> > +
> > +	/*
> > +	 * managing i/o requests and associated device resources
> > +	 */
> > +	.urb_enqueue		= ehci_urb_enqueue,
> > +	.urb_dequeue		= ehci_urb_dequeue,
> > +	.endpoint_disable	= ehci_endpoint_disable,
> > +	.endpoint_reset		= ehci_endpoint_reset,
> > +
> > +	/*
> > +	 * scheduling support
> > +	 */
> > +	.get_frame_number	= ehci_get_frame,
> > +
> > +	/*
> > +	 * root hub support
> > +	 */
> > +	.hub_status_data	= ehci_hub_status_data,
> > +	.hub_control		= ehci_hub_control,
> > +	.bus_suspend		= ehci_bus_suspend,
> > +	.bus_resume		= ehci_bus_resume,
> > +	.relinquish_port	= ehci_relinquish_port,
> > +	.port_handed_over	= ehci_port_handed_over,
> > +
> > +	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
> > +};
> > +
> > +static int ehci_hcd_msp_drv_probe(struct platform_device *pdev)
> > +{
> > +	int ret;
> > +
> > +	pr_debug("In ehci_hcd_msp_drv_probe");
> > +
> > +	if (usb_disabled())
> > +		return -ENODEV;
> > +
> > +	gpio_request(MSP_PIN_USB0_HOST_DEV, "USB0_HOST_DEV_GPIO");
> > +#ifdef CONFIG_MSP_HAS_DUAL_USB
> > +	gpio_request(MSP_PIN_USB1_HOST_DEV, "USB1_HOST_DEV_GPIO");
> > +#endif
> > +
> > +	ret = usb_hcd_msp_probe(&ehci_msp_hc_driver, pdev);
> > +
> > +	return ret;
> > +}
> > +
> > +static int ehci_hcd_msp_drv_remove(struct platform_device *pdev)
> > +{
> > +	struct usb_hcd *hcd = platform_get_drvdata(pdev);
> > +
> > +	usb_hcd_msp_remove(hcd, pdev);
> > +
> > +	/* free TWI GPIO USB_HOST_DEV pin */
> > +	gpio_free(MSP_PIN_USB0_HOST_DEV);
> > +#ifdef CONFIG_MSP_HAS_DUAL_USB
> > +	gpio_free(MSP_PIN_USB1_HOST_DEV);
> > +#endif
> > +
> > +	return 0;
> > +}
> > +
> > +MODULE_ALIAS("pmcmsp-ehci");
> > +
> > +static struct platform_driver ehci_hcd_msp_driver = {
> > +	.probe		= ehci_hcd_msp_drv_probe,
> > +	.remove		= ehci_hcd_msp_drv_remove,
> > +	.driver		= {
> > +		.name	= "pmcmsp-ehci",
> > +		.owner	= THIS_MODULE,
> > +#ifdef	CONFIG_PM
> > +		.pm	= &ehci_msp_pmops,
> > +#endif
> > +	},
> > +};
> > diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
> > index 799ac16..1b71d6a 100644
> > --- a/drivers/usb/host/ehci.h
> > +++ b/drivers/usb/host/ehci.h
> > @@ -134,6 +134,7 @@ struct ehci_hcd {			/* one per controller */
> >  	unsigned		amd_l1_fix:1;
> >  	unsigned		fs_i_thresh:1;	/* Intel iso scheduling */
> >  	unsigned		use_dummy_qh:1;	/* AMD Frame List table quirk*/
> > +	unsigned		pmc_msp_tdi:1;	/* PMC MSP tdi quirk*/
> 
> This part of the patch doesn't apply cleanly anymore, care to refresh it
> against linux-next, and make all of the other fixes and resend it?

Ok. originally created against linux-mips git head. Will resend the
revised patch once I fix issues you have pointed

> 
> thanks,
> 
> greg k-h


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/