RE: [Patch v3] AM35xx: Craneboard: Add USB EHCI support

[Srinath R]

Hi Manjunath, 

Thanks for the review, Please find my response inline.

With Regards
Srinath

-----Original Message-----
From: G, Manjunath Kondaiah [mailto:manjugk@xxxxxx] 
Sent: Thursday, December 02, 2010 11:56 AM
To: srinath@xxxxxxxxxxxxxxxxxxxx
Cc: linux-omap@xxxxxxxxxxxxxxx; jdk@xxxxxx; tony@xxxxxxxxxxx;
linux-kernel@xxxxxxxxxxxxxxx; linux@xxxxxxxxxxxxxxxx;
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; khilman@xxxxxxxxxxxxxxxxxxx;
nm@xxxxxx; nagendra@xxxxxxxxxxxxxxxxxxxx; umeshk@xxxxxxxxxxxxxxxxxxxx
Subject: Re: [Patch v3] AM35xx: Craneboard: Add USB EHCI support

* srinath@xxxxxxxxxxxxxxxxxxxx <srinath@xxxxxxxxxxxxxxxxxxxx> [2010-12-01
22:28:50 +0530]:

> From: Srinath <srinath@xxxxxxxxxxxxxxxxxxxx>
> 
> AM3517/05 Craneboard has one EHCI interface on board using port1.
> 
> GPIO35 is used as power enable.
> GPIO38 is used as port1 PHY reset.
> 
> History:
>
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&;
q=t
> 
> Signed-off-by: Srinath <srinath@xxxxxxxxxxxxxxxxxxxx>
> ---
>  arch/arm/mach-omap2/board-am3517crane.c |   40
+++++++++++++++++++++++++++++++
>  1 files changed, 40 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/board-am3517crane.c
b/arch/arm/mach-omap2/board-am3517crane.c
> index 13ead33..6fd5dfe 100644
> --- a/arch/arm/mach-omap2/board-am3517crane.c
> +++ b/arch/arm/mach-omap2/board-am3517crane.c
> @@ -28,8 +28,13 @@
>  
[...]
>  static void __init am3517_crane_init(void)
>  {
> +	int ret;
> +
>  	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
>  	omap_serial_init();
> +
> +	/* Configure GPIO for EHCI port */
> +	omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT);

This is non void function. You can consider return value for further
processing.

<Srinath> Sure, I will put check and resend patch 
> +
> +	ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
> +	if (ret < 0) {
> +		pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER);
> +		return;
> +	}
> +
> +	ret = gpio_direction_output(GPIO_USB_POWER, 1);
> +	if (ret < 0)
> +		goto err;
> +
> +	omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT);

-Ditto-
<Srinath> Sure, I will put check and resend patch

Also, why there is no gpio_request for "GPIO_USB_NRESET"

<Srinath> This is taken care by USB driver in drivers/usb/host/ehci-omap.c

-Manjunath

[...]

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/