Re: Failed to initialize MSI interrupts && ioremap reserve_memtype failed -22
From: Mark Knecht
Date: Wed Apr 07 2010 - 11:57:50 EST
On Wed, Apr 7, 2010 at 7:54 AM, Clemens Ladisch <clemens@xxxxxxxxxx> wrote:
> Mark Knecht wrote:
>> Â ÂNew hardware and I haven't seen these messages before so I thought
>> I'd post them.
>
> Both might be harmless. ÂPlease show the entire boot log.
>
>
> Regards,
> Clemens
>
Hopefully you mean the contents of dmesg. If it's something else let me know.
If the mail server deletes the text file attachment I'll reply again
pasting the text in by hand.
Thanks,
Mark
ffffea0000000000-ffffea0005ffffff] PMD -> [ffff880028600000-ffff88002dbfffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x001b0000
Movable zone start PFN for each node
early_node_map[7] active PFN ranges
0: 0x00000000 -> 0x0000008f
0: 0x00000090 -> 0x0000009d
0: 0x00000100 -> 0x000cf4bd
0: 0x000cf4bf -> 0x000cf4c4
0: 0x000cf7bf -> 0x000cf7df
0: 0x000cf7ff -> 0x000cf800
0: 0x00100000 -> 0x001b0000
On node 0 totalpages: 1569919
DMA zone: 56 pages used for memmap
DMA zone: 108 pages reserved
DMA zone: 3832 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 830747 pages, LIFO batch:31
Normal zone: 9856 pages used for memmap
Normal zone: 711040 pages, LIFO batch:31
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a301 base: 0xfed00000
16 Processors exceeds NR_CPUS limit of 8
SMP: Allowing 8 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
Allocating PCI resources starting at d0000000 (gap: d0000000:28000000)
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
PERCPU: Embedded 25 pages/cpu @ffff880028200000 s73304 r8192 d20904 u262144
pcpu-alloc: s73304 r8192 d20904 u262144 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 4 5 6 7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1545619
Kernel command line: root=/dev/md3
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Checking aperture...
No AGP bridge found
Memory: 6104092k/7077888k available (3345k kernel code, 798212k absent, 174704k reserved, 3225k data, 440k init)
Experimental preemptable hierarchical RCU implementation.
NR_IRQS:512
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2667.184 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5334.36 BogoMIPS (lpj=2667184)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 9 MCE banks
CPU0: Thermal monitoring enabled (TM1)
CPU 0 MCA banks CMCI:2 CMCI:3 CMCI:5 CMCI:6 CMCI:8
using mwait in idle threads.
Performance Events: Nehalem/Corei7 events, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 000000070000000f
Freeing SMP alternatives: 33k freed
ACPI: Core revision 20091214
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz stepping 05
Booting Node 0, Processors #1
CPU 1 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
#2
CPU 2 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
#3
CPU 3 MCA banks CMCI:2 CMCI:3 CMCI:5 SHD:6 SHD:8
#4
CPU 4 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
#5
CPU 5 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
#6
CPU 6 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
#7 Ok.
CPU 7 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
Brought up 8 CPUs
Total of 8 processors activated (42661.97 BogoMIPS).
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
dca service started, version 1.12.1
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A08:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000cbfff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfedfffff] (ignored)
pci_root PNP0A08:00: host bridge window [mem 0xd0000000-0xf7ffffff] (ignored)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:19.0: reg 10: [mem 0xd3200000-0xd321ffff]
pci 0000:00:19.0: reg 14: [mem 0xd3223000-0xd3223fff]
pci 0000:00:19.0: reg 18: [io 0x3100-0x311f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20: [io 0x30e0-0x30ff]
pci 0000:00:1a.1: reg 20: [io 0x30c0-0x30df]
pci 0000:00:1a.2: reg 20: [io 0x30a0-0x30bf]
pci 0000:00:1a.7: reg 10: [mem 0xd3222000-0xd32223ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10: [mem 0xf0000000-0xf0003fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0x3080-0x309f]
pci 0000:00:1d.1: reg 20: [io 0x3060-0x307f]
pci 0000:00:1d.2: reg 20: [io 0x3040-0x305f]
pci 0000:00:1d.7: reg 10: [mem 0xd3221000-0xd32213ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
pci 0000:00:1f.2: reg 10: [io 0x3128-0x312f]
pci 0000:00:1f.2: reg 14: [io 0x3134-0x3137]
pci 0000:00:1f.2: reg 18: [io 0x3120-0x3127]
pci 0000:00:1f.2: reg 1c: [io 0x3130-0x3133]
pci 0000:00:1f.2: reg 20: [io 0x3020-0x303f]
pci 0000:00:1f.2: reg 24: [mem 0xd3220000-0xd32207ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10: [mem 0xf0004000-0xf00040ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0x3000-0x301f]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:02:00.0: reg 10: [mem 0xd2000000-0xd2ffffff]
pci 0000:02:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
pci 0000:02:00.0: reg 1c: [mem 0xd0000000-0xd1ffffff 64bit]
pci 0000:02:00.0: reg 24: [io 0x2000-0x207f]
pci 0000:02:00.0: reg 30: [mem 0xfff80000-0xffffffff pref]
pci 0000:00:03.0: PCI bridge to [bus 02-02]
pci 0000:00:03.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:03.0: bridge window [mem 0xd0000000-0xd2ffffff]
pci 0000:00:03.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
pci 0000:00:07.0: PCI bridge to [bus 03-03]
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:00:1c.1: PCI bridge to [bus 05-05]
pci 0000:06:00.0: reg 10: [io 0x1018-0x101f]
pci 0000:06:00.0: reg 14: [io 0x1024-0x1027]
pci 0000:06:00.0: reg 18: [io 0x1010-0x1017]
pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023]
pci 0000:06:00.0: reg 20: [io 0x1000-0x100f]
pci 0000:06:00.0: reg 24: [mem 0xd3100000-0xd31003ff]
pci 0000:06:00.0: supports D1
pci 0000:06:00.0: PME# supported from D0 D1 D3hot
pci 0000:06:00.0: PME# disabled
pci 0000:00:1c.4: PCI bridge to [bus 06-06]
pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.4: bridge window [mem 0xd3100000-0xd31fffff]
pci 0000:07:03.0: reg 10: [mem 0xd3004000-0xd30047ff]
pci 0000:07:03.0: reg 14: [mem 0xd3000000-0xd3003fff]
pci 0000:07:03.0: supports D1 D2
pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot
pci 0000:07:03.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xd3000000-0xd30fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:05: [io 0x0500-0x053f] has been reserved
system 00:05: [io 0x0400-0x047f] has been reserved
system 00:05: [io 0x0680-0x06ff] has been reserved
pci 0000:02:00.0: no compatible bridge window for [mem 0xfff80000-0xffffffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io disabled]
pci 0000:00:01.0: bridge window [mem disabled]
pci 0000:00:01.0: bridge window [mem pref disabled]
pci 0000:02:00.0: BAR 6: can't assign mem pref (size 0x80000)
pci 0000:00:03.0: PCI bridge to [bus 02-02]
pci 0000:00:03.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:03.0: bridge window [mem 0xd0000000-0xd2ffffff]
pci 0000:00:03.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
pci 0000:00:07.0: PCI bridge to [bus 03-03]
pci 0000:00:07.0: bridge window [io disabled]
pci 0000:00:07.0: bridge window [mem disabled]
pci 0000:00:07.0: bridge window [mem pref disabled]
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:00:1c.0: bridge window [io disabled]
pci 0000:00:1c.0: bridge window [mem disabled]
pci 0000:00:1c.0: bridge window [mem pref disabled]
pci 0000:00:1c.1: PCI bridge to [bus 05-05]
pci 0000:00:1c.1: bridge window [io disabled]
pci 0000:00:1c.1: bridge window [mem disabled]
pci 0000:00:1c.1: bridge window [mem pref disabled]
pci 0000:00:1c.4: PCI bridge to [bus 06-06]
pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.4: bridge window [mem 0xd3100000-0xd31fffff]
pci 0000:00:1c.4: bridge window [mem pref disabled]
pci 0000:00:1e.0: PCI bridge to [bus 07-07]
pci 0000:00:1e.0: bridge window [io disabled]
pci 0000:00:1e.0: bridge window [mem 0xd3000000-0xd30fffff]
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd2ffffff]
pci_bus 0000:02: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
pci_bus 0000:06: resource 0 [io 0x1000-0x1fff]
pci_bus 0000:06: resource 1 [mem 0xd3100000-0xd31fffff]
pci_bus 0000:07: resource 1 [mem 0xd3000000-0xd30fffff]
pci_bus 0000:07: resource 3 [io 0x0000-0xffff]
pci_bus 0000:07: resource 4 [mem 0x00000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
UDP hash table entries: 4096 (order: 5, 131072 bytes)
UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:02:00.0: Boot video device
PCI: CLS 64 bytes, default 64
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
software IO TLB at phys 0x20000000 - 0x24000000
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/W].
msgmni has been set to 11923
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:01.0: setting latency timer to 64
pcieport 0000:00:03.0: setting latency timer to 64
pcieport 0000:00:07.0: setting latency timer to 64
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.4: setting latency timer to 64
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
ide0: no devices on the port
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide1: no devices on the port
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
ide-cd driver 5.00
Loading iSCSI transport class v2.0-870.
SCSI Media Changer driver v0.25
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 19
ata2: SATA max UDMA/133 irq 19
ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
ata4: SATA max UDMA/133 abar m2048@0xd3220000 port 0xd3220280 irq 19
ata5: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
ata6: SATA max UDMA/133 abar m2048@0xd3220000 port 0xd3220380 irq 19
ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ
ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP
ahci 0000:06:00.0: MV_AHCI HACK: port_map 7 -> 3
ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
ahci 0000:06:00.0: flags: 64bit stag led slum part
ahci 0000:06:00.0: setting latency timer to 64
scsi6 : ahci
scsi7 : ahci
scsi8 : ahci
ata7: SATA max UDMA/133 abar m1024@0xd3100000 port 0xd3100100 irq 16
ata8: SATA max UDMA/133 abar m1024@0xd3100000 port 0xd3100180 irq 16
ata9: DUMMY
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@xxxxxxxxxx
cpuidle: using governor ladder
cpuidle: using governor menu
ioatdma: Intel(R) QuickData Technology Driver 4.00
TCP cubic registered
NET: Registered protocol family 17
ata6: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5002ABYS-02B1B0, 02.03B03, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: ATA-8: WDC WD5002ABYS-02B1B0, 02.03B03, max UDMA/133
ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata2.00: ATAPI: Optiarc DVD RW AD-7241S, 1.03, max UDMA/100, ATAPI AN
ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133
ata5.00: configured for UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
ata3.00: configured for UDMA/133
ata2.00: configured for UDMA/100
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 80.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7241S 1.03 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
scsi 2:0:0:0: Direct-Access ATA WDC WD5002ABYS-0 02.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
scsi 4:0:0:0: Direct-Access ATA WDC WD5002ABYS-0 02.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sda1 sda2 sda3 sda4 < sdc1 sdc2 sdc3
sda5 >
sd 4:0:0:0: [sdc] Attached SCSI disk
sdb1 sdb2 sdb3
sd 0:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: [sdb] Attached SCSI disk
ata8: SATA link down (SStatus 0 SControl 300)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 2 and added 2 devices.
md: autorun ...
md: considering sdb3 ...
md: adding sdb3 ...
md: adding sdc3 ...
md: created md3
md: bind<sdc3>
md: bind<sdb3>
md: running: <sdb3><sdc3>
raid1: raid set md3 active with 2 out of 2 mirrors
md3: detected capacity change from 0 to 42960551936
md: ... autorun DONE.
md3: unknown partition table
kjournald starting. Commit interval 5 seconds
EXT3-fs (md3): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 9:3.
Freeing unused kernel memory: 440k freed
Write protecting the kernel read-only data: 6144k
Freeing unused kernel memory: 732k freed
Freeing unused kernel memory: 780k freed
udev: starting version 149
Monitor-Mwait will be used to enter C-1 state
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 4:0:0:0: Attached scsi generic sg3 type 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd3222000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.33-gentoo ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
uhci_hcd: USB Universal Host Controller Interface driver
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd3221000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.33-gentoo ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030e0
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030c0
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 19, io base 0x000030a0
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.33-gentoo uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
Linux agpgart interface v0.103
firewire_ohci 0000:07:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
0000:00:19.0: 0000:00:19.0: Failed to initialize MSI interrupts. Falling back to legacy interrupts.
firewire_ohci: Added fw-ohci device 0000:07:03.0, OHCI version 1.10
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:b1:9a:fd
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: ffffff-0ff
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
usb 5-2: new low speed USB device using uhci_hcd and address 2
firewire_core: created device fw0: GUID 00902700025d5a61, S400
usb 5-2: New USB device found, idVendor=045e, idProduct=0084
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-2: Product: Basic Optical Mouse
usb 5-2: Manufacturer: Microsoft
usbcore: registered new interface driver hiddev
input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.0/input/input2
generic-usb 0003:045E:0084.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1a.2-2/input0
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nvidia 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:02:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 195.36.15 Fri Mar 12 00:29:13 PST 2010
usb 8-2: new low speed USB device using uhci_hcd and address 2
usb 8-2: New USB device found, idVendor=047b, idProduct=0011
usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 8-2: Product: Standard USB Keyboard
usb 8-2: Manufacturer: Silitek
input: Silitek Standard USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input3
generic-usb 0003:047B:0011.0002: input,hidraw1: USB HID v1.00 Keyboard [Silitek Standard USB Keyboard ] on usb-0000:00:1d.2-2/input0
EXT3-fs (md3): using internal journal
Adding 4200988k swap on /dev/sda2. Priority:-1 extents:1 across:4200988k
Adding 4200988k swap on /dev/sdb2. Priority:-2 extents:1 across:4200988k
Adding 4200988k swap on /dev/sdc2. Priority:-3 extents:1 across:4200988k
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
0000:00:19.0: eth0: 10/100 speed: disabling TSO
NET: Registered protocol family 10
ioremap reserve_memtype failed -22
eth0: no IPv6 routers present
md: data-check of RAID array md3
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
md: using 128k window, over a total of 41953664 blocks.