Re: [PATCH] x86: Reduce the default HZ value

From: Paul E. McKenney
Date: Thu May 07 2009 - 14:01:26 EST


On Thu, May 07, 2009 at 07:38:24PM +0200, Peter Zijlstra wrote:
> On Thu, 2009-05-07 at 10:36 -0700, Paul E. McKenney wrote:
> > On Thu, May 07, 2009 at 07:18:38PM +0200, Peter Zijlstra wrote:
> > > On Thu, 2009-05-07 at 19:13 +0200, Peter Zijlstra wrote:
> > > > On Thu, 2009-05-07 at 19:09 +0200, Peter Zijlstra wrote:
> > > > > On Thu, 2009-05-07 at 10:13 -0400, Christoph Lameter wrote:
> > > > > > I think we need to reduce the general tick frequency to be as low as
> > > > > > possible. With high resolution timers the tick frequency is just the
> > > > > > frequency with which the timer interrupt disturbs a running application.
> > > > > >
> > > > > > Are there any benefits remaining from frequent timer interrupts? I would
> > > > > > think that 60 HZ would be sufficient.
> > > > > >
> > > > > > It would be good if the kernel would be truly tickless. Scheduler events
> > > > > > would be driven by the scheduling intervals and not the invokations of the
> > > > > > scheduler softirq.
> > > > >
> > > > > The only thing that's driven by the softirq is load-balancing, there's
> > > > > way more to the scheduler-tick than kicking that thing awake every so
> > > > > often.
> > > > >
> > > > > The problem is that running the scheduler of off hrtimers is too
> > > > > expensive. We have the code, we tried it, people complained.
> > > >
> > > > Therefore, decreasing the HZ value to say 50, we'd get a minimum
> > > > involuntary preemption granularity of 20ms, something on the high end of
> > > > barely usable.
> > >
> > > Another user is RCU, the grace period is tick driven, growing these
> > > ticks by a factor 50 or so might require some tinkering with forced
> > > grace periods when we notice our batch queues getting too long.
> >
> > One approach would be to enter nohz mode when running a CPU-bound
> > application on a CPU that had nothing else (other than the idle task)
> > on its runqueue and for which rcu_needs_cpu() returns zero. In this
> > mode, RCU would need to be informed on each system call, perhaps with an
> > rcu_kernel_enter() and rcu_kernel_exit() that work like rcu_irq_enter()
> > and rcu_irq_exit() -- and that perhaps replace rcu_irq_enter() and
> > rcu_irq_exit().
> >
> > Then RCU would ignore any CPU that was executing a CPU-bound application,
> > allowing the HZ to be dialed down as low as you like, or perhaps really
> > entering something like nohz mode.
>
> Which would make syscall more expensive, not something you'd want to
> do :-)

In general, I agree. However, in the case where you have a single
CPU-bound task running in user mode, you don't care that much about
syscall performance. So, yes, this would mean having yet another config
variable that users running big CPU-bound scientific applications would
need to worry about, which is not perfect either.

For whatever it is worth, the added overhead on entry would be something
like the following:

void rcu_irq_enter(void)
{
struct rcu_dynticks *rdtp = &__get_cpu_var(rcu_dynticks);

if (rdtp->dynticks_nesting++)
return;
rdtp->dynticks++;
WARN_ON_RATELIMIT(!(rdtp->dynticks & 0x1), &rcu_rs);
smp_mb(); /* CPUs seeing ++ must see later RCU read-side crit sects */
}

On exit, a bit more:

void rcu_irq_exit(void)
{
struct rcu_dynticks *rdtp = &__get_cpu_var(rcu_dynticks);

if (--rdtp->dynticks_nesting)
return;
smp_mb(); /* CPUs seeing ++ must see prior RCU read-side crit sects */
rdtp->dynticks++;
WARN_ON_RATELIMIT(rdtp->dynticks & 0x1, &rcu_rs);

/* If the interrupt queued a callback, get out of dyntick mode. */
if (__get_cpu_var(rcu_data).nxtlist ||
__get_cpu_var(rcu_bh_data).nxtlist)
set_need_resched();
}

But I could move the callback check into call_rcu(), which would get the
overhead of rcu_irq_exit() down to about that of rcu_irq_enter().

Thanx, Paul
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/