[bug] sata detection problem
From: Ingo Molnar
Date: Sun Feb 08 2009 - 01:36:03 EST
Hm, in a boot test i had this boot failure:
[ 15.504053] calling piix_init+0x0/0x30 @ 1
[ 15.508050] ata_piix 0000:00:1f.1: version 2.12
[ 15.516193] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 15.520029] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 15.524072] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 15.528115] scsi0 : ata_piix
[ 15.531526] scsi1 : ata_piix
[ 15.544044] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 15.548028] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 15.716358] ata1.00: ATAPI: ïVïVïVïVïVïïïïïïïïïïïïïïïïïïïïïïïïïïïïïï, ïïVïVïV, max UDMA7
[ 15.720044] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 15.740296] ata1.00: configured for UDMA/33
[ 15.744117] async_waiting @ 1
[ 15.748027] async_continuing @ 1 after 0 usec
[ 15.752066] isa bounce pool size: 16 pages
[ 15.756124] scsi scan: INQUIRY result too short (5), using 36
[ 15.760030] scsi 0:0:0:0: Direct-Access PQ: 0 ANSI: 5
[ 15.768197] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 15.772359] async_waiting @ 1
[ 15.776047] async_continuing @ 1 after 0 usec
[ 15.940033] async_waiting @ 1
[ 15.944027] async_continuing @ 1 after 0 usec
[ 15.948613] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 15.952029] ata_piix 0000:00:1f.2: PCI INT B -> Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 15.956030] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 15.961683] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 15.964087] scsi2 : ata_piix
[ 15.968192] scsi3 : ata_piix
[ 15.972153] ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400 bmdma 0x8400 irq 11
[ 15.976028] ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800 bmdma 0x8408 irq 11
[ 16.176051] ata3.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 16.180027] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 16.248061] ata3.00: configured for UDMA/133
[ 16.252031] async_waiting @ 1
[ 16.256027] async_continuing @ 1 after 0 usec
[ 16.260175] scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 16.264348] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 16.268056] sd 2:0:0:0: [sdb] Write Protect is off
[ 16.272028] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 16.276097] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.280135] sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 16.284055] sd 2:0:0:0: [sdb] Write Protect is off
[ 16.288028] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 16.292078] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.296029] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
[ 16.337818] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 16.340313] async_waiting @ 1
[ 16.344028] async_continuing @ 1 after 0 usec
[ 16.508033] async_waiting @ 1
[ 16.512027] async_continuing @ 1 after 0 usec
[ 16.516143] initcall piix_init+0x0/0x30 returned 0 after 984375 usecs
[ 16.520029] calling sil_init+0x0/0x20 @ 1
Look at the weird sda detection. The only _real_ device on this system is the
ST3320620AS disk which got detected as sdb. But the bogus sda entry crashed the
(older) OS installation on the box:
[ 20.132252] VFS: Cannot open root device "sda3" or unknown-block(0,0)
Find below a successful bootup. Bug is very sporadic. (seems timing related)
Ingo
[ 0.000000] Linux version 2.6.29-rc3-00697-gae1a25d (mingo@aldebaran) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #52 Sun Feb 8 06:54:35 CET 2009
[ 0.000000] Command line: root=/dev/sda3 earlyprintk=serial,ttyS0,115200 console=ttyS0,115200 console=tty 3 profile=0 debug initcall_debug apic=debug apic=verbose ignore_loglevel sysrq_always_enabled
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffa0000 (usable)
[ 0.000000] BIOS-e820: 000000007ffa0000 - 000000007ffae000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ffae000 - 000000007ffe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[ 0.000000] console [earlyser0] enabled
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] DMI 2.3 present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] last_pfn = 0x7ffa0 max_arch_pfn = 0x100000000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
[ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000007ffa0000 (usable)
[ 0.000000] modified: 000000007ffa0000 - 000000007ffae000 (ACPI data)
[ 0.000000] modified: 000000007ffae000 - 000000007ffe0000 (ACPI NVS)
[ 0.000000] modified: 000000007ffe0000 - 0000000080000000 (reserved)
[ 0.000000] modified: 00000000ffb80000 - 0000000100000000 (reserved)
[ 0.000000] init_memory_mapping: 0000000000000000-000000007ffa0000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007ffa0000 page 4k
[ 0.000000] kernel direct mapping tables up to 7ffa0000 @ 10000-14000
[ 0.000000] last_map_addr: 7ffa0000 end: 7ffa0000
[ 0.000000] ACPI: RSDP 000FACD0, 0024 (r2 ACPIAM)
[ 0.000000] ACPI: XSDT 7FFA0100, 0044 (r1 A M I OEMXSDT 10000630 MSFT 97)
[ 0.000000] ACPI: FACP 7FFA0290, 00F4 (r3 A M I OEMFACP 10000630 MSFT 97)
[ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
[ 0.000000] ACPI: DSDT 7FFA0410, 8318 (r1 A0227 A0227000 0 INTL 2002026)
[ 0.000000] ACPI: FACS 7FFAE000, 0040
[ 0.000000] ACPI: APIC 7FFA0390, 0080 (r1 A M I OEMAPIC 10000630 MSFT 97)
[ 0.000000] ACPI: OEMB 7FFAE040, 0066 (r1 A M I AMI_OEM 10000630 MSFT 97)
[ 0.000000] ACPI: MCFG 7FFA8730, 003C (r1 A M I OEMMCFG 10000630 MSFT 97)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (5 early reservations) ==> bootmem [0000000000 - 007ffa0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 00013be814] TEXT DATA BSS ==> [0000200000 - 00013be814]
[ 0.000000] #3 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #4 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes.
[ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes.
[ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes.
[ 0.000000] found SMP MP-table at [ffff8800000ff780] 000ff780
[ 0.000000] [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001600000-ffff8800031fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007ffa0
[ 0.000000] On node 0 totalpages: 524079
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 103 pages reserved
[ 0.000000] DMA zone: 3824 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7111 pages used for memmap
[ 0.000000] DMA32 zone: 512985 pages, LIFO batch:31
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: NR_CPUS/possible_cpus limit of 1 reached. Processor 1/0x1 ignored.
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] mapped APIC to ffffffffff5fc000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffffffff5fb000 (fec00000)
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7fb80000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516809
[ 0.000000] Kernel command line: root=/dev/sda3 earlyprintk=serial,ttyS0,115200 console=ttyS0,115200 console=tty 3 profile=0 debug initcall_debug apic=debug apic=verbose ignore_loglevel sysrq_always_enabled
[ 0.000000] debug: sysrq always enabled.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3456.959 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console handover: boot [earlyser0] -> real [tty0]
[ 0.004000] console [ttyS0] enabled
[ 0.004000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.004000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.004000] Checking aperture...
[ 0.004000] No AGP bridge found
[ 0.004000] Memory: 2045728k/2096768k available (9108k kernel code, 452k absent, 50196k reserved, 5116k data, 660k init)
[ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.004013] Calibrating delay loop (skipped), value calculated using timer frequency.. 6913.91 BogoMIPS (lpj=13827836)
[ 0.012066] Security Framework initialized
[ 0.016043] Mount-cache hash table entries: 256
[ 0.024104] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.028003] CPU: L2 cache: 2048K
[ 0.032018] CPU0: Thermal monitoring enabled (TM1)
[ 0.036004] using mwait in idle threads.
[ 0.040003] CPU: Intel(R) Pentium(R) D CPU 3.00GHz stepping 02
[ 0.051273] ACPI: Core revision 20081204
[ 0.088087] calling spawn_ksoftirqd+0x0/0x40 @ 1
[ 0.092032] initcall spawn_ksoftirqd+0x0/0x40 returned 0 after 0 usecs
[ 0.096005] calling relay_init+0x0/0x8 @ 1
[ 0.100004] initcall relay_init+0x0/0x8 returned 0 after 0 usecs
[ 0.104004] calling tracer_alloc_buffers+0x0/0x10b @ 1
[ 0.108352] initcall tracer_alloc_buffers+0x0/0x10b returned 0 after 0 usecs
[ 0.112005] Setting APIC routing to flat
[ 0.116008] enabled ExtINT on CPU#0
[ 0.120142] ENABLING IO-APIC IRQs
[ 0.124003] init IO_APIC IRQs
[ 0.128003] 2-0 (apicid-pin) not connected
[ 0.132008] IOAPIC[0]: Set routing entry (2-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
[ 0.136007] IOAPIC[0]: Set routing entry (2-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
[ 0.140006] IOAPIC[0]: Set routing entry (2-3 -> 0x33 -> IRQ 3 Mode:0 Active:0)
[ 0.144005] IOAPIC[0]: Set routing entry (2-4 -> 0x34 -> IRQ 4 Mode:0 Active:0)
[ 0.148005] IOAPIC[0]: Set routing entry (2-5 -> 0x35 -> IRQ 5 Mode:0 Active:0)
[ 0.152005] IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
[ 0.156005] IOAPIC[0]: Set routing entry (2-7 -> 0x37 -> IRQ 7 Mode:0 Active:0)
[ 0.160005] IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
[ 0.164005] IOAPIC[0]: Set routing entry (2-9 -> 0x39 -> IRQ 9 Mode:1 Active:0)
[ 0.168005] IOAPIC[0]: Set routing entry (2-10 -> 0x3a -> IRQ 10 Mode:0 Active:0)
[ 0.172005] IOAPIC[0]: Set routing entry (2-11 -> 0x3b -> IRQ 11 Mode:0 Active:0)
[ 0.176005] IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
[ 0.180005] IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
[ 0.184005] IOAPIC[0]: Set routing entry (2-14 -> 0x3e -> IRQ 14 Mode:0 Active:0)
[ 0.188005] IOAPIC[0]: Set routing entry (2-15 -> 0x3f -> IRQ 15 Mode:0 Active:0)
[ 0.192003] 2-16 2-17 2-18 2-19 2-20 2-21 2-22 2-23 (apicid-pin) not connected
[ 0.200149] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.246106] Using local APIC timer interrupts.
[ 0.246106] calibrating APIC timer ...
[ 0.252001] ... lapic delta = 1440414
[ 0.252001] ..... delta 1440414
[ 0.252001] ..... mult: 61861443
[ 0.252001] ..... calibration result: 921864
[ 0.252001] ..... CPU clock speed is 3456.3980 MHz.
[ 0.252001] ..... host bus clock speed is 230.1864 MHz.
[ 0.252001] ... verify APIC timer
[ 0.360045] ... jiffies delta = 25
[ 0.363490] ... jiffies result ok
[ 0.366127] calling init_cpufreq_transition_notifier_list+0x0/0x1b @ 1
[ 0.368006] initcall init_cpufreq_transition_notifier_list+0x0/0x1b returned 0 after 0 usecs
[ 0.372005] calling net_ns_init+0x0/0x182 @ 1
[ 0.376003] net_namespace: 1352 bytes
[ 0.380007] initcall net_ns_init+0x0/0x182 returned 0 after 3906 usecs
[ 0.384004] calling cpufreq_tsc+0x0/0x28 @ 1
[ 0.388003] initcall cpufreq_tsc+0x0/0x28 returned 0 after 0 usecs
[ 0.392005] calling print_banner+0x0/0xe @ 1
[ 0.396003] Booting paravirtualized kernel on bare hardware
[ 0.400004] initcall print_banner+0x0/0xe returned 0 after 3906 usecs
[ 0.404004] calling sysctl_init+0x0/0x16 @ 1
[ 0.408007] initcall sysctl_init+0x0/0x16 returned 0 after 0 usecs
[ 0.412004] calling ksysfs_init+0x0/0xbb @ 1
[ 0.416108] initcall ksysfs_init+0x0/0xbb returned 0 after 0 usecs
[ 0.420004] calling async_init+0x0/0x4b @ 1
[ 0.424186] initcall async_init+0x0/0x4b returned 0 after 0 usecs
[ 0.428117] calling init_jiffies_clocksource+0x0/0x12 @ 1
[ 0.432006] initcall init_jiffies_clocksource+0x0/0x12 returned 0 after 0 usecs
[ 0.436004] calling pm_init+0x0/0x43 @ 1
[ 0.440010] initcall pm_init+0x0/0x43 returned 0 after 0 usecs
[ 0.444005] calling filelock_init+0x0/0x2e @ 1
[ 0.448010] initcall filelock_init+0x0/0x2e returned 0 after 0 usecs
[ 0.452004] calling init_misc_binfmt+0x0/0x44 @ 1
[ 0.456007] initcall init_misc_binfmt+0x0/0x44 returned 0 after 0 usecs
[ 0.460004] calling init_script_binfmt+0x0/0x12 @ 1
[ 0.464005] initcall init_script_binfmt+0x0/0x12 returned 0 after 0 usecs
[ 0.468004] calling init_elf_binfmt+0x0/0x12 @ 1
[ 0.472005] initcall init_elf_binfmt+0x0/0x12 returned 0 after 0 usecs
[ 0.476004] calling init_compat_elf_binfmt+0x0/0x12 @ 1
[ 0.480005] initcall init_compat_elf_binfmt+0x0/0x12 returned 0 after 0 usecs
[ 0.484004] calling debugfs_init+0x0/0x56 @ 1
[ 0.488009] initcall debugfs_init+0x0/0x56 returned 0 after 0 usecs
[ 0.492005] calling random32_init+0x0/0xad @ 1
[ 0.496005] initcall random32_init+0x0/0xad returned 0 after 0 usecs
[ 0.500007] calling gnttab_init+0x0/0x1d0 @ 1
[ 0.504005] initcall gnttab_init+0x0/0x1d0 returned -19 after 0 usecs
[ 0.508004] calling cpufreq_core_init+0x0/0x2c @ 1
[ 0.512004] initcall cpufreq_core_init+0x0/0x2c returned 0 after 0 usecs
[ 0.516004] calling cpuidle_init+0x0/0x20 @ 1
[ 0.520010] initcall cpuidle_init+0x0/0x20 returned 0 after 0 usecs
[ 0.524004] calling sock_init+0x0/0x60 @ 1
[ 0.528038] initcall sock_init+0x0/0x60 returned 0 after 0 usecs
[ 0.532005] calling netpoll_init+0x0/0x27 @ 1
[ 0.536005] initcall netpoll_init+0x0/0x27 returned 0 after 0 usecs
[ 0.540005] calling netlink_proto_init+0x0/0x16f @ 1
[ 0.544023] NET: Registered protocol family 16
[ 0.548026] initcall netlink_proto_init+0x0/0x16f returned 0 after 3906 usecs
[ 0.552005] calling bdi_class_init+0x0/0x41 @ 1
[ 0.556104] initcall bdi_class_init+0x0/0x41 returned 0 after 0 usecs
[ 0.560004] calling kobject_uevent_init+0x0/0x49 @ 1
[ 0.564023] initcall kobject_uevent_init+0x0/0x49 returned 0 after 0 usecs
[ 0.568005] calling gpiolib_sysfs_init+0x0/0x9b @ 1
[ 0.572096] initcall gpiolib_sysfs_init+0x0/0x9b returned 0 after 0 usecs
[ 0.576004] calling pcibus_class_init+0x0/0x19 @ 1
[ 0.580149] initcall pcibus_class_init+0x0/0x19 returned 0 after 0 usecs
[ 0.584004] calling pci_driver_init+0x0/0x14 @ 1
[ 0.588113] initcall pci_driver_init+0x0/0x14 returned 0 after 0 usecs
[ 0.592005] calling backlight_class_init+0x0/0x60 @ 1
[ 0.596130] initcall backlight_class_init+0x0/0x60 returned 0 after 0 usecs
[ 0.600006] calling xenbus_probe_init+0x0/0x167 @ 1
[ 0.604020] initcall xenbus_probe_init+0x0/0x167 returned -19 after 0 usecs
[ 0.608005] calling tty_class_init+0x0/0x31 @ 1
[ 0.612085] initcall tty_class_init+0x0/0x31 returned 0 after 0 usecs
[ 0.616005] calling vtconsole_class_init+0x0/0xcc @ 1
[ 0.620196] initcall vtconsole_class_init+0x0/0xcc returned 0 after 0 usecs
[ 0.624006] calling i2c_init+0x0/0x6b @ 1
[ 0.628266] i2c-core: driver [dummy] registered
[ 0.632006] initcall i2c_init+0x0/0x6b returned 0 after 3906 usecs
[ 0.636027] calling amd_postcore_init+0x0/0x45 @ 1
[ 0.640005] initcall amd_postcore_init+0x0/0x45 returned 0 after 0 usecs
[ 0.644004] calling arch_kdebugfs_init+0x0/0x31 @ 1
[ 0.648008] initcall arch_kdebugfs_init+0x0/0x31 returned 0 after 0 usecs
[ 0.652004] calling ffh_cstate_init+0x0/0x37 @ 1
[ 0.656005] initcall ffh_cstate_init+0x0/0x37 returned 0 after 0 usecs
[ 0.660004] calling acpi_pci_init+0x0/0x5a @ 1
[ 0.664004] ACPI: bus type pci registered
[ 0.668005] initcall acpi_pci_init+0x0/0x5a returned 0 after 3906 usecs
[ 0.672004] calling init_acpi_device_notify+0x0/0x4b @ 1
[ 0.676004] initcall init_acpi_device_notify+0x0/0x4b returned 0 after 0 usecs
[ 0.680004] calling dmi_id_init+0x0/0x30f @ 1
[ 0.684224] initcall dmi_id_init+0x0/0x30f returned 0 after 0 usecs
[ 0.688005] calling pci_arch_init+0x0/0x6a @ 1
[ 0.692074] PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support.
[ 0.696003] PCI: Using configuration type 1 for base access
[ 0.700011] initcall pci_arch_init+0x0/0x6a returned 0 after 7812 usecs
[ 0.704004] calling topology_init+0x0/0x16 @ 1
[ 0.708086] initcall topology_init+0x0/0x16 returned 0 after 0 usecs
[ 0.712004] calling param_sysfs_init+0x0/0x1eb @ 1
[ 0.750429] initcall param_sysfs_init+0x0/0x1eb returned 0 after 31250 usecs
[ 0.752009] calling pm_sysrq_init+0x0/0x20 @ 1
[ 0.756290] initcall pm_sysrq_init+0x0/0x20 returned 0 after 0 usecs
[ 0.760310] calling readahead_init+0x0/0x3b @ 1
[ 0.764858] initcall readahead_init+0x0/0x3b returned 0 after 0 usecs
[ 0.768006] calling init_bio+0x0/0xda @ 1
[ 0.772171] bio: create slab <bio-0> at 0
[ 0.776098] initcall init_bio+0x0/0xda returned 0 after 3906 usecs
[ 0.780005] calling integrity_init+0x0/0x38 @ 1
[ 0.784040] initcall integrity_init+0x0/0x38 returned 0 after 0 usecs
[ 0.788006] calling cryptomgr_init+0x0/0x3a @ 1
[ 0.792130] initcall cryptomgr_init+0x0/0x3a returned 0 after 0 usecs
[ 0.796018] calling blk_settings_init+0x0/0x2c @ 1
[ 0.800005] initcall blk_settings_init+0x0/0x2c returned 0 after 0 usecs
[ 0.804004] calling blk_ioc_init+0x0/0x2a @ 1
[ 0.808007] initcall blk_ioc_init+0x0/0x2a returned 0 after 0 usecs
[ 0.812004] calling blk_softirq_init+0x0/0x35 @ 1
[ 0.816004] initcall blk_softirq_init+0x0/0x35 returned 0 after 0 usecs
[ 0.820004] calling genhd_device_init+0x0/0x7e @ 1
[ 0.824139] initcall genhd_device_init+0x0/0x7e returned 0 after 0 usecs
[ 0.828005] calling blk_dev_integrity_init+0x0/0x2a @ 1
[ 0.832058] initcall blk_dev_integrity_init+0x0/0x2a returned 0 after 0 usecs
[ 0.836006] calling gpiolib_debugfs_init+0x0/0x24 @ 1
[ 0.840010] initcall gpiolib_debugfs_init+0x0/0x24 returned 0 after 0 usecs
[ 0.844005] calling pca953x_init+0x0/0x17 @ 1
[ 0.848098] i2c-core: driver [pca953x] registered
[ 0.852006] initcall pca953x_init+0x0/0x17 returned 0 after 3906 usecs
[ 0.856039] calling pci_slot_init+0x0/0x50 @ 1
[ 0.860011] initcall pci_slot_init+0x0/0x50 returned 0 after 0 usecs
[ 0.864005] calling fbmem_init+0x0/0x95 @ 1
[ 0.868105] initcall fbmem_init+0x0/0x95 returned 0 after 0 usecs
[ 0.872006] calling acpi_init+0x0/0x239 @ 1
[ 0.877001] ACPI: EC: Look up EC in DSDT
[ 0.955936] ACPI: Interpreter enabled
[ 0.956007] ACPI: (supports S0 S1 S3 S5)
[ 0.961328] ACPI: Using IOAPIC for interrupt routing
[ 0.964162] initcall acpi_init+0x0/0x239 returned 0 after 85937 usecs
[ 0.968006] calling acpi_scan_init+0x0/0x109 @ 1
[ 1.009244] initcall acpi_scan_init+0x0/0x109 returned 0 after 35156 usecs
[ 1.012064] calling acpi_ec_init+0x0/0x61 @ 1
[ 1.016100] initcall acpi_ec_init+0x0/0x61 returned 0 after 0 usecs
[ 1.020006] calling dock_init+0x0/0x8d @ 1
[ 1.024443] ACPI: No dock devices found.
[ 1.028006] initcall dock_init+0x0/0x8d returned 0 after 3906 usecs
[ 1.032005] calling acpi_pci_root_init+0x0/0x28 @ 1
[ 1.036171] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 1.040213] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 1.044006] pci 0000:00:01.0: PME# disabled
[ 1.048194] pci 0000:00:1b.0: reg 10 64bit mmio: [0xd7cf8000-0xd7cfbfff]
[ 1.052044] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.056006] pci 0000:00:1b.0: PME# disabled
[ 1.060060] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.064006] pci 0000:00:1c.0: PME# disabled
[ 1.068063] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 1.072006] pci 0000:00:1c.3: PME# disabled
[ 1.076049] pci 0000:00:1d.0: reg 20 io port: [0x7000-0x701f]
[ 1.080052] pci 0000:00:1d.1: reg 20 io port: [0x7400-0x741f]
[ 1.084051] pci 0000:00:1d.2: reg 20 io port: [0x7800-0x781f]
[ 1.088051] pci 0000:00:1d.3: reg 20 io port: [0x8000-0x801f]
[ 1.092056] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd7cff800-0xd7cffbff]
[ 1.096050] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 1.100006] pci 0000:00:1d.7: PME# disabled
[ 1.104129] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 1.108009] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 1.112006] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 1.116007] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
[ 1.120045] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 1.124008] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 1.128008] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 1.132008] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 1.136008] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
[ 1.140065] pci 0000:00:1f.2: reg 10 io port: [0x9800-0x9807]
[ 1.144008] pci 0000:00:1f.2: reg 14 io port: [0x9400-0x9403]
[ 1.148007] pci 0000:00:1f.2: reg 18 io port: [0x9000-0x9007]
[ 1.152007] pci 0000:00:1f.2: reg 1c io port: [0x8800-0x8803]
[ 1.156007] pci 0000:00:1f.2: reg 20 io port: [0x8400-0x840f]
[ 1.160008] pci 0000:00:1f.2: reg 24 32bit mmio: [0xd7cffc00-0xd7cfffff]
[ 1.164021] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.168006] pci 0000:00:1f.2: PME# disabled
[ 1.172048] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[ 1.176055] pci 0000:04:00.0: reg 10 32bit mmio: [0xd8000000-0xdfffffff]
[ 1.180008] pci 0000:04:00.0: reg 14 io port: [0xe000-0xe0ff]
[ 1.184007] pci 0000:04:00.0: reg 18 32bit mmio: [0xd7fe0000-0xd7feffff]
[ 1.188017] pci 0000:04:00.0: reg 30 32bit mmio: [0xd7fc0000-0xd7fdffff]
[ 1.192021] pci 0000:04:00.0: supports D1 D2
[ 1.196032] pci 0000:04:00.1: reg 10 32bit mmio: [0xd7ff0000-0xd7ffffff]
[ 1.200039] pci 0000:04:00.1: supports D1 D2
[ 1.204042] pci 0000:00:01.0: bridge io port: [0xe000-0xefff]
[ 1.208005] pci 0000:00:01.0: bridge 32bit mmio: [0xd7f00000-0xd7ffffff]
[ 1.212006] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd8000000-0xdfffffff]
[ 1.216041] pci 0000:00:1c.0: bridge io port: [0xd000-0xdfff]
[ 1.220069] pci 0000:02:00.0: reg 10 64bit mmio: [0xd7efc000-0xd7efffff]
[ 1.224010] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff]
[ 1.228027] pci 0000:02:00.0: reg 30 32bit mmio: [0xd7ec0000-0xd7edffff]
[ 1.232042] pci 0000:02:00.0: supports D1 D2
[ 1.236004] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.240007] pci 0000:02:00.0: PME# disabled
[ 1.244041] pci 0000:00:1c.3: bridge io port: [0xc000-0xcfff]
[ 1.248006] pci 0000:00:1c.3: bridge 32bit mmio: [0xd7e00000-0xd7efffff]
[ 1.252045] pci 0000:01:01.0: reg 10 32bit mmio: [0xd7ddf000-0xd7ddffff]
[ 1.256009] pci 0000:01:01.0: reg 14 32bit mmio: [0xd7dde000-0xd7ddefff]
[ 1.260041] pci 0000:01:01.0: supports D1
[ 1.264038] pci 0000:01:03.0: reg 10 io port: [0xb800-0xb807]
[ 1.268009] pci 0000:01:03.0: reg 14 io port: [0xb400-0xb403]
[ 1.272008] pci 0000:01:03.0: reg 18 io port: [0xb000-0xb007]
[ 1.276008] pci 0000:01:03.0: reg 1c io port: [0xa800-0xa803]
[ 1.280008] pci 0000:01:03.0: reg 20 io port: [0xa400-0xa40f]
[ 1.284013] pci 0000:01:03.0: reg 30 32bit mmio: [0xd7de0000-0xd7dfffff]
[ 1.288057] pci 0000:00:1e.0: transparent bridge
[ 1.292006] pci 0000:00:1e.0: bridge io port: [0xa000-0xbfff]
[ 1.296006] pci 0000:00:1e.0: bridge 32bit mmio: [0xd7d00000-0xd7dfffff]
[ 1.300022] pci_bus 0000:00: on NUMA node 0
[ 1.304021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.312655] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 1.316282] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 1.320615] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 1.324296] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[ 1.348142] initcall acpi_pci_root_init+0x0/0x28 returned 0 after 304688 usecs
[ 1.352007] calling acpi_pci_link_init+0x0/0x63 @ 1
[ 1.356458] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 1.364748] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 1.372746] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 1.380746] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 1.388747] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 1.396745] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 1.404744] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 1.414061] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 1.421875] initcall acpi_pci_link_init+0x0/0x63 returned 0 after 62500 usecs
[ 1.424006] calling acpi_power_init+0x0/0x77 @ 1
[ 1.428380] initcall acpi_power_init+0x0/0x77 returned 0 after 0 usecs
[ 1.432005] Clocksource tsc unstable (delta = 160815809 ns)
[ 1.436046] calling acpi_system_init+0x0/0x274 @ 1
[ 1.440121] ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - 5F, should be 52 [20081204]
[ 1.449220] initcall acpi_system_init+0x0/0x274 returned 0 after 7812 usecs
[ 1.452006] calling acpi_debug_init+0x0/0xae @ 1
[ 1.456014] initcall acpi_debug_init+0x0/0xae returned 0 after 0 usecs
[ 1.460006] calling pnp_init+0x0/0x12 @ 1
[ 1.464097] initcall pnp_init+0x0/0x12 returned 0 after 0 usecs
[ 1.468007] calling setup_shutdown_event+0x0/0x21 @ 1
[ 1.472033] initcall setup_shutdown_event+0x0/0x21 returned 0 after 0 usecs
[ 1.476006] calling misc_init+0x0/0xa4 @ 1
[ 1.480102] initcall misc_init+0x0/0xa4 returned 0 after 0 usecs
[ 1.484007] calling tps_init+0x0/0xc7 @ 1
[ 1.488029] tps65010: version 2 May 2005
[ 1.492087] i2c-core: driver [tps65010] registered
[ 1.496092] i2c-core: driver [tps65010] unregistered
[ 1.516102] i2c-core: driver [tps65010] registered
[ 1.520088] i2c-core: driver [tps65010] unregistered
[ 1.540097] i2c-core: driver [tps65010] registered
[ 1.544088] i2c-core: driver [tps65010] unregistered
[ 1.548009] tps65010: no chip?
[ 1.552007] initcall tps_init+0x0/0xc7 returned -19 after 62500 usecs
[ 1.556006] calling twl4030_init+0x0/0x14 @ 1
[ 1.560084] i2c-core: driver [twl4030] registered
[ 1.564007] initcall twl4030_init+0x0/0x14 returned 0 after 3906 usecs
[ 1.568019] calling phy_init+0x0/0x3a @ 1
[ 1.572255] initcall phy_init+0x0/0x3a returned 0 after 0 usecs
[ 1.576006] calling init_scsi+0x0/0xa1 @ 1
[ 1.580500] SCSI subsystem initialized
[ 1.584007] initcall init_scsi+0x0/0xa1 returned 0 after 3906 usecs
[ 1.588038] calling ata_init+0x0/0x3fd @ 1
[ 1.592061] libata version 3.00 loaded.
[ 1.596007] initcall ata_init+0x0/0x3fd returned 0 after 3906 usecs
[ 1.600041] calling usb_init+0x0/0x168 @ 1
[ 1.604297] usbcore: registered new interface driver usbfs
[ 1.608111] usbcore: registered new interface driver hub
[ 1.612136] usbcore: registered new device driver usb
[ 1.616007] initcall usb_init+0x0/0x168 returned 0 after 11718 usecs
[ 1.620048] calling serio_init+0x0/0xa0 @ 1
[ 1.624114] initcall serio_init+0x0/0xa0 returned 0 after 0 usecs
[ 1.628007] calling gameport_init+0x0/0xa0 @ 1
[ 1.632140] initcall gameport_init+0x0/0xa0 returned 0 after 0 usecs
[ 1.636007] calling input_init+0x0/0x119 @ 1
[ 1.640117] initcall input_init+0x0/0x119 returned 0 after 0 usecs
[ 1.644007] calling rtc_init+0x0/0x65 @ 1
[ 1.648099] initcall rtc_init+0x0/0x65 returned 0 after 0 usecs
[ 1.652006] calling hwmon_init+0x0/0x44 @ 1
[ 1.656098] initcall hwmon_init+0x0/0x44 returned 0 after 0 usecs
[ 1.660006] calling thermal_init+0x0/0x43 @ 1
[ 1.664097] initcall thermal_init+0x0/0x43 returned 0 after 0 usecs
[ 1.668006] calling leds_init+0x0/0x40 @ 1
[ 1.672098] initcall leds_init+0x0/0x40 returned 0 after 0 usecs
[ 1.676007] calling acpi_wmi_init+0x0/0x55 @ 1
[ 1.680108] ACPI: WMI: Mapper loaded
[ 1.684007] initcall acpi_wmi_init+0x0/0x55 returned 0 after 3906 usecs
[ 1.688019] calling ac97_bus_init+0x0/0x12 @ 1
[ 1.692094] initcall ac97_bus_init+0x0/0x12 returned 0 after 0 usecs
[ 1.696006] calling pci_subsys_init+0x0/0x130 @ 1
[ 1.700018] PCI: Using ACPI for IRQ routing
[ 1.704122] initcall pci_subsys_init+0x0/0x130 returned 0 after 3906 usecs
[ 1.708006] calling proto_init+0x0/0x12 @ 1
[ 1.712013] initcall proto_init+0x0/0x12 returned 0 after 0 usecs
[ 1.716006] calling net_dev_init+0x0/0x141 @ 1
[ 1.720277] initcall net_dev_init+0x0/0x141 returned 0 after 0 usecs
[ 1.724007] calling neigh_init+0x0/0x71 @ 1
[ 1.728020] initcall neigh_init+0x0/0x71 returned 0 after 0 usecs
[ 1.732007] calling fib_rules_init+0x0/0xb0 @ 1
[ 1.736008] initcall fib_rules_init+0x0/0xb0 returned 0 after 0 usecs
[ 1.740006] calling pktsched_init+0x0/0xc4 @ 1
[ 1.744012] initcall pktsched_init+0x0/0xc4 returned 0 after 0 usecs
[ 1.748007] calling tc_filter_init+0x0/0x4c @ 1
[ 1.752006] initcall tc_filter_init+0x0/0x4c returned 0 after 0 usecs
[ 1.756006] calling genl_init+0x0/0xe1 @ 1
[ 1.776031] initcall genl_init+0x0/0xe1 returned 0 after 15625 usecs
[ 1.780007] calling cipso_v4_init+0x0/0x5b @ 1
[ 1.784022] initcall cipso_v4_init+0x0/0x5b returned 0 after 0 usecs
[ 1.788007] calling wanrouter_init+0x0/0x5a @ 1
[ 1.792006] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[ 1.796017] initcall wanrouter_init+0x0/0x5a returned 0 after 3906 usecs
[ 1.800006] calling wireless_nlevent_init+0x0/0x27 @ 1
[ 1.804007] initcall wireless_nlevent_init+0x0/0x27 returned 0 after 0 usecs
[ 1.808006] calling netlbl_init+0x0/0x8a @ 1
[ 1.812005] NetLabel: Initializing
[ 1.816005] NetLabel: domain hash size = 128
[ 1.820005] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.824079] NetLabel: unlabeled traffic allowed by default
[ 1.828007] initcall netlbl_init+0x0/0x8a returned 0 after 15625 usecs
[ 1.832007] calling rfkill_init+0x0/0x69 @ 1
[ 1.836094] initcall rfkill_init+0x0/0x69 returned 0 after 0 usecs
[ 1.840007] calling sysctl_init+0x0/0x51 @ 1
[ 1.844008] initcall sysctl_init+0x0/0x51 returned 0 after 0 usecs
[ 1.848009] calling xen_mc_debugfs+0x0/0x11a @ 1
[ 1.852040] initcall xen_mc_debugfs+0x0/0x11a returned 0 after 0 usecs
[ 1.856007] calling xen_mmu_debugfs+0x0/0x2c0 @ 1
[ 1.860049] initcall xen_mmu_debugfs+0x0/0x2c0 returned 0 after 0 usecs
[ 1.864007] calling pci_iommu_init+0x0/0x18 @ 1
[ 1.868040] initcall pci_iommu_init+0x0/0x18 returned 0 after 0 usecs
[ 1.872007] calling print_all_ICs+0x0/0x53a @ 1
[ 1.876006]
[ 1.876006] printing PIC contents
[ 1.880007] ... PIC IMR: ffff
[ 1.883106] ... PIC IRR: 0c29
[ 1.884005] ... PIC ISR: 0000
[ 1.888007] ... PIC ELCR: 0e28
[ 1.891105]
[ 1.891106] printing local APIC contents on CPU#0/0:
[ 1.892004] ... APIC ID: 00000000 (0)
[ 1.892004] ... APIC VERSION: 00050014
[ 1.892004] ... APIC TASKPRI: 00000000 (00)
[ 1.892004] ... APIC PROCPRI: 00000000
[ 1.892004] ... APIC LDR: 01000000
[ 1.892004] ... APIC DFR: ffffffff
[ 1.892004] ... APIC SPIV: 000001ff
[ 1.892004] ... APIC ISR field:
[ 1.892004] 0123456789abcdef0123456789abcdef
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] ... APIC TMR field:
[ 1.892004] 0123456789abcdef0123456789abcdef
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] ... APIC IRR field:
[ 1.892004] 0123456789abcdef0123456789abcdef
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000000000000000000000
[ 1.892004] 00000000000000010000000000000000
[ 1.892004] ... APIC ESR: 00000000
[ 1.892004] ... APIC ICR: 000c0630
[ 1.892004] ... APIC ICR2: ff000000
[ 1.892004] ... APIC LVTT: 000200ef
[ 1.892004] ... APIC LVTPC: 00010000
[ 1.892004] ... APIC LVT0: 00010700
[ 1.892004] ... APIC LVT1: 00000400
[ 1.892004] ... APIC LVTERR: 000000fe
[ 1.892004] ... APIC TMICT: 0000e110
[ 1.892004] ... APIC TMCCT: 0000d9a0
[ 1.892004] ... APIC TDCR: 00000003
[ 1.892004]
[ 1.892005] number of MP IRQ sources: 15.
[ 1.896005] number of IO-APIC #2 registers: 24.
[ 1.900005] testing the IO APIC.......................
[ 1.904010]
[ 1.908005] IO APIC #2......
[ 1.910931] .... register #00: 02000000
[ 1.912005] ....... : physical APIC id: 02
[ 1.916005] ....... : Delivery Type: 0
[ 1.920005] ....... : LTS : 0
[ 1.924005] .... register #01: 00170020
[ 1.928005] ....... : max redirection entries: 0017
[ 1.932005] ....... : PRQ implemented: 0
[ 1.936005] ....... : IO APIC version: 0020
[ 1.940005] .... IRQ redirection table:
[ 1.944005] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
[ 1.948008] 00 000 1 0 0 0 0 0 0 00
[ 1.956008] 01 001 0 0 0 0 0 1 1 31
[ 1.960008] 02 001 0 0 0 0 0 1 1 30
[ 1.964008] 03 001 0 0 0 0 0 1 1 33
[ 1.972008] 04 001 0 0 0 0 0 1 1 34
[ 1.976008] 05 001 0 0 0 0 0 1 1 35
[ 1.980008] 06 001 0 0 0 0 0 1 1 36
[ 1.988008] 07 001 0 0 0 0 0 1 1 37
[ 1.992008] 08 001 0 0 0 0 0 1 1 38
[ 1.996008] 09 001 0 1 0 0 0 1 1 39
[ 2.004008] 0a 001 0 0 0 0 0 1 1 3A
[ 2.008008] 0b 001 0 0 0 0 0 1 1 3B
[ 2.012008] 0c 001 0 0 0 0 0 1 1 3C
[ 2.020008] 0d 001 0 0 0 0 0 1 1 3D
[ 2.024008] 0e 001 0 0 0 0 0 1 1 3E
[ 2.028008] 0f 001 0 0 0 0 0 1 1 3F
[ 2.036008] 10 000 1 0 0 0 0 0 0 00
[ 2.040008] 11 000 1 0 0 0 0 0 0 00
[ 2.044008] 12 000 1 0 0 0 0 0 0 00
[ 2.052008] 13 000 1 0 0 0 0 0 0 00
[ 2.056008] 14 000 1 0 0 0 0 0 0 00
[ 2.060008] 15 000 1 0 0 0 0 0 0 00
[ 2.068008] 16 000 1 0 0 0 0 0 0 00
[ 2.072008] 17 000 1 0 0 0 0 0 0 00
[ 2.076006] IRQ to pin mappings:
[ 2.080006] IRQ0 -> 0:2
[ 2.084238] IRQ1 -> 0:1
[ 2.086818] IRQ3 -> 0:3
[ 2.088809] IRQ4 -> 0:4
[ 2.092237] IRQ5 -> 0:5
[ 2.094817] IRQ6 -> 0:6
[ 2.096800] IRQ7 -> 0:7
[ 2.100237] IRQ8 -> 0:8
[ 2.102809] IRQ9 -> 0:9
[ 2.104809] IRQ10 -> 0:10
[ 2.108006] IRQ11 -> 0:11
[ 2.110758] IRQ12 -> 0:12
[ 2.112896] IRQ13 -> 0:13
[ 2.116238] IRQ14 -> 0:14
[ 2.118984] IRQ15 -> 0:15
[ 2.120913] .................................... done.
[ 2.124007] initcall print_all_ICs+0x0/0x53a returned 0 after 242187 usecs
[ 2.128007] calling hpet_late_init+0x0/0xf1 @ 1
[ 2.132080] hpet clockevent registered
[ 2.136015] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 2.141069] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 2.145009] initcall hpet_late_init+0x0/0xf1 returned 0 after 11718 usecs
[ 2.148008] calling clocksource_done_booting+0x0/0x12 @ 1
[ 2.152007] initcall clocksource_done_booting+0x0/0x12 returned 0 after 0 usecs
[ 2.156012] Switched to high resolution mode on CPU 0
[ 2.161115] calling rb_init_debugfs+0x0/0x50 @ 1
[ 2.165879] initcall rb_init_debugfs+0x0/0x50 returned 0 after 6 usecs
[ 2.172459] calling tracer_init_debugfs+0x0/0x34e @ 1
[ 2.177687] initcall tracer_init_debugfs+0x0/0x34e returned 0 after 35 usecs
[ 2.184784] calling init_pipe_fs+0x0/0x51 @ 1
[ 2.189299] initcall init_pipe_fs+0x0/0x51 returned 0 after 17 usecs
[ 2.195703] calling init_mnt_writers+0x0/0x13 @ 1
[ 2.200549] initcall init_mnt_writers+0x0/0x13 returned 0 after 0 usecs
[ 2.207212] calling anon_inode_init+0x0/0x12e @ 1
[ 2.212082] initcall anon_inode_init+0x0/0x12e returned 0 after 23 usecs
[ 2.218834] calling acpi_event_init+0x0/0x52 @ 1
[ 2.236030] initcall acpi_event_init+0x0/0x52 returned 0 after 12145 usecs
[ 2.242954] calling pnpacpi_init+0x0/0x8e @ 1
[ 2.247454] pnp: PnP ACPI init
[ 2.250575] ACPI: bus type pnp registered
[ 2.255677] IOAPIC[0]: Set routing entry (2-8 -> 0x38 -> IRQ 8 Mode:0 Active:0)
[ 2.263351] IOAPIC[0]: Set routing entry (2-13 -> 0x3d -> IRQ 13 Mode:0 Active:0)
[ 2.273858] IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
[ 2.285019] IOAPIC[0]: Set routing entry (2-7 -> 0x37 -> IRQ 7 Mode:0 Active:0)
[ 2.301155] IOAPIC[0]: Set routing entry (2-4 -> 0x34 -> IRQ 4 Mode:0 Active:0)
[ 2.311673] pnp: PnP ACPI: found 14 devices
[ 2.315909] ACPI: ACPI bus type pnp unregistered
[ 2.320646] initcall pnpacpi_init+0x0/0x8e returned 0 after 71474 usecs
[ 2.327306] calling pnp_system_init+0x0/0x13 @ 1
[ 2.332078] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[ 2.339274] system 00:08: ioport range 0x290-0x297 has been reserved
[ 2.345685] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 2.352085] system 00:09: ioport range 0x800-0x87f has been reserved
[ 2.358488] system 00:09: ioport range 0x480-0x4bf has been reserved
[ 2.364893] system 00:09: ioport range 0x900-0x91f has been reserved
[ 2.371299] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 2.378484] system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 2.385670] system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 2.393216] system 00:09: iomem range 0xfff00000-0xffffffff has been reserved
[ 2.400406] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 2.407595] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
[ 2.414783] system 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved
[ 2.421970] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 2.428637] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
[ 2.435303] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 2.442315] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
[ 2.449774] initcall pnp_system_init+0x0/0x13 returned 0 after 114949 usecs
[ 2.456787] calling chr_dev_init+0x0/0xa3 @ 1
[ 2.462289] initcall chr_dev_init+0x0/0xa3 returned 0 after 939 usecs
[ 2.468782] calling firmware_class_init+0x0/0x7f @ 1
[ 2.473984] initcall firmware_class_init+0x0/0x7f returned 0 after 79 usecs
[ 2.480993] calling cpufreq_gov_performance_init+0x0/0x12 @ 1
[ 2.487008] initcall cpufreq_gov_performance_init+0x0/0x12 returned 0 after 1 usecs
[ 2.494729] calling pcibios_assign_resources+0x0/0x8a @ 1
[ 2.500316] pci 0000:00:01.0: PCI bridge, secondary bus 0000:04
[ 2.506281] pci 0000:00:01.0: IO window: 0xe000-0xefff
[ 2.511647] pci 0000:00:01.0: MEM window: 0xd7f00000-0xd7ffffff
[ 2.517792] pci 0000:00:01.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff
[ 2.525428] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
[ 2.531398] pci 0000:00:1c.0: IO window: 0xd000-0xdfff
[ 2.536763] pci 0000:00:1c.0: MEM window: disabled
[ 2.541780] pci 0000:00:1c.0: PREFETCH window: disabled
[ 2.547234] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:02
[ 2.553202] pci 0000:00:1c.3: IO window: 0xc000-0xcfff
[ 2.558569] pci 0000:00:1c.3: MEM window: 0xd7e00000-0xd7efffff
[ 2.564712] pci 0000:00:1c.3: PREFETCH window: disabled
[ 2.570169] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[ 2.576134] pci 0000:00:1e.0: IO window: 0xa000-0xbfff
[ 2.581500] pci 0000:00:1e.0: MEM window: 0xd7d00000-0xd7dfffff
[ 2.587645] pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x000000880fffff
[ 2.595289] alloc irq_desc for 16 on cpu 0 node 0
[ 2.599275] alloc kstat_irqs on cpu 0 node 0
[ 2.604711] IOAPIC[0]: Set routing entry (2-16 -> 0x49 -> IRQ 16 Mode:1 Active:1)
[ 2.612258] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.619011] pci 0000:00:01.0: setting latency timer to 64
[ 2.624465] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.631212] pci 0000:00:1c.0: setting latency timer to 64
[ 2.636667] alloc irq_desc for 19 on cpu 0 node 0
[ 2.640659] alloc kstat_irqs on cpu 0 node 0
[ 2.646084] IOAPIC[0]: Set routing entry (2-19 -> 0x51 -> IRQ 19 Mode:1 Active:1)
[ 2.653632] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.660384] pci 0000:00:1c.3: setting latency timer to 64
[ 2.665838] pci 0000:00:1e.0: setting latency timer to 64
[ 2.671288] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 2.676823] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 2.683748] pci_bus 0000:04: resource 0 io: [0xe000-0xefff]
[ 2.689458] pci_bus 0000:04: resource 1 mem: [0xd7f00000-0xd7ffffff]
[ 2.695863] pci_bus 0000:04: resource 2 mem: [0xd8000000-0xdfffffff]
[ 2.702267] pci_bus 0000:04: resource 3 mem: [0x0-0x0]
[ 2.707451] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
[ 2.713162] pci_bus 0000:03: resource 1 mem: [0x0-0x0]
[ 2.718344] pci_bus 0000:03: resource 2 mem: [0x0-0x0]
[ 2.723882] pci_bus 0000:03: resource 3 mem: [0x0-0x0]
[ 2.729066] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 2.734776] pci_bus 0000:02: resource 1 mem: [0xd7e00000-0xd7efffff]
[ 2.741181] pci_bus 0000:02: resource 2 mem: [0x0-0x0]
[ 2.746363] pci_bus 0000:02: resource 3 mem: [0x0-0x0]
[ 2.751547] pci_bus 0000:01: resource 0 io: [0xa000-0xbfff]
[ 2.757258] pci_bus 0000:01: resource 1 mem: [0xd7d00000-0xd7dfffff]
[ 2.763662] pci_bus 0000:01: resource 2 mem: [0x88000000-0x880fffff]
[ 2.770067] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
[ 2.775597] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 2.782524] initcall pcibios_assign_resources+0x0/0x8a returned 0 after 275640 usecs
[ 2.790332] calling sysctl_core_init+0x0/0x38 @ 1
[ 2.795186] initcall sysctl_core_init+0x0/0x38 returned 0 after 9 usecs
[ 2.801849] calling inet_init+0x0/0x25a @ 1
[ 2.806196] NET: Registered protocol family 2
[ 2.856066] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 2.863781] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 2.874517] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 2.881648] TCP: Hash tables configured (established 262144 bind 65536)
[ 2.888309] TCP reno registered
[ 2.900162] initcall inet_init+0x0/0x25a returned 0 after 91775 usecs
[ 2.906657] calling af_unix_init+0x0/0x65 @ 1
[ 2.911173] NET: Registered protocol family 1
[ 2.915592] initcall af_unix_init+0x0/0x65 returned 0 after 4334 usecs
[ 2.922173] calling populate_rootfs+0x0/0xfb @ 1
[ 2.927401] initcall populate_rootfs+0x0/0xfb returned 0 after 462 usecs
[ 2.934158] calling calgary_fixup_tce_spaces+0x0/0xf8 @ 1
[ 2.939695] initcall calgary_fixup_tce_spaces+0x0/0xf8 returned -19 after 0 usecs
[ 2.947241] calling i8259A_init_sysfs+0x0/0x29 @ 1
[ 2.952437] initcall i8259A_init_sysfs+0x0/0x29 returned 0 after 257 usecs
[ 2.959358] calling vsyscall_init+0x0/0xa3 @ 1
[ 2.963950] initcall vsyscall_init+0x0/0xa3 returned 0 after 3 usecs
[ 2.970355] calling sbf_init+0x0/0x103 @ 1
[ 2.974595] initcall sbf_init+0x0/0x103 returned 0 after 0 usecs
[ 2.980652] calling i8237A_init_sysfs+0x0/0x29 @ 1
[ 2.985754] initcall i8237A_init_sysfs+0x0/0x29 returned 0 after 166 usecs
[ 2.992682] calling add_rtc_cmos+0x0/0xce @ 1
[ 2.997210] initcall add_rtc_cmos+0x0/0xce returned 0 after 5 usecs
[ 3.003526] calling cache_sysfs_init+0x0/0x221 @ 1
[ 3.008724] initcall cache_sysfs_init+0x0/0x221 returned 0 after 262 usecs
[ 3.015649] calling mce_init_device+0x0/0x120 @ 1
[ 3.020814] initcall mce_init_device+0x0/0x120 returned 0 after 293 usecs
[ 3.027652] calling periodic_mcheck_init+0x0/0x41 @ 1
[ 3.032909] initcall periodic_mcheck_init+0x0/0x41 returned 0 after 2 usecs
[ 3.039923] calling thermal_throttle_init_device+0x0/0x44 @ 1
[ 3.045812] initcall thermal_throttle_init_device+0x0/0x44 returned 0 after 4 usecs
[ 3.053538] calling threshold_init_device+0x0/0x57 @ 1
[ 3.058817] initcall threshold_init_device+0x0/0x57 returned 0 after 0 usecs
[ 3.065915] calling init_lapic_sysfs+0x0/0x2f @ 1
[ 3.070921] initcall init_lapic_sysfs+0x0/0x2f returned 0 after 157 usecs
[ 3.077763] calling ioapic_init_sysfs+0x0/0xd0 @ 1
[ 3.082891] initcall ioapic_init_sysfs+0x0/0xd0 returned 0 after 158 usecs
[ 3.089821] calling start_periodic_check_for_corruption+0x0/0x40 @ 1
[ 3.096336] Scanning for low memory corruption every 60 seconds
[ 3.102309] initcall start_periodic_check_for_corruption+0x0/0x40 returned 0 after 5831 usecs
[ 3.110903] calling uv_ptc_init+0x0/0x51 @ 1
[ 3.115316] initcall uv_ptc_init+0x0/0x51 returned 0 after 1 usecs
[ 3.121545] calling uv_bau_init+0x0/0x410 @ 1
[ 3.126045] initcall uv_bau_init+0x0/0x410 returned 0 after 1 usecs
[ 3.132361] calling sgi_uv_sysfs_init+0x0/0xaf @ 1
[ 3.137302] initcall sgi_uv_sysfs_init+0x0/0xaf returned 0 after 7 usecs
[ 3.144053] calling aes_init+0x0/0x20 @ 1
[ 3.148296] initcall aes_init+0x0/0x20 returned 0 after 87 usecs
[ 3.154349] calling crc32c_intel_mod_init+0x0/0x30 @ 1
[ 3.159659] initcall crc32c_intel_mod_init+0x0/0x30 returned -19 after 0 usecs
[ 3.166950] calling init_vdso_vars+0x0/0x241 @ 1
[ 3.171732] initcall init_vdso_vars+0x0/0x241 returned 0 after 21 usecs
[ 3.178399] calling ia32_binfmt_init+0x0/0x14 @ 1
[ 3.183247] initcall ia32_binfmt_init+0x0/0x14 returned 0 after 2 usecs
[ 3.189908] calling sysenter_setup+0x0/0x377 @ 1
[ 3.194674] initcall sysenter_setup+0x0/0x377 returned 0 after 6 usecs
[ 3.201253] calling init_aout_binfmt+0x0/0x1b @ 1
[ 3.206098] initcall init_aout_binfmt+0x0/0x1b returned 0 after 1 usecs
[ 3.212761] calling init_sched_debug_procfs+0x0/0x2c @ 1
[ 3.218223] initcall init_sched_debug_procfs+0x0/0x2c returned 0 after 8 usecs
[ 3.225511] calling proc_schedstat_init+0x0/0x22 @ 1
[ 3.230621] initcall proc_schedstat_init+0x0/0x22 returned 0 after 4 usecs
[ 3.237548] calling proc_execdomains_init+0x0/0x2f @ 1
[ 3.242832] initcall proc_execdomains_init+0x0/0x2f returned 0 after 4 usecs
[ 3.249926] calling ioresources_init+0x0/0x3c @ 1
[ 3.254777] initcall ioresources_init+0x0/0x3c returned 0 after 7 usecs
[ 3.261442] calling uid_cache_init+0x0/0x85 @ 1
[ 3.266119] initcall uid_cache_init+0x0/0x85 returned 0 after 5 usecs
[ 3.272606] calling init_posix_timers+0x0/0xe8 @ 1
[ 3.277542] initcall init_posix_timers+0x0/0xe8 returned 0 after 5 usecs
[ 3.284288] calling init_posix_cpu_timers+0x0/0xb3 @ 1
[ 3.289567] initcall init_posix_cpu_timers+0x0/0xb3 returned 0 after 0 usecs
[ 3.296664] calling nsproxy_cache_init+0x0/0x38 @ 1
[ 3.301686] initcall nsproxy_cache_init+0x0/0x38 returned 0 after 3 usecs
[ 3.308520] calling timekeeping_init_device+0x0/0x29 @ 1
[ 3.314133] initcall timekeeping_init_device+0x0/0x29 returned 0 after 157 usecs
[ 3.321598] calling init_clocksource_sysfs+0x0/0x52 @ 1
[ 3.327138] initcall init_clocksource_sysfs+0x0/0x52 returned 0 after 157 usecs
[ 3.334512] calling init_timer_list_procfs+0x0/0x2c @ 1
[ 3.339910] initcall init_timer_list_procfs+0x0/0x2c returned 0 after 4 usecs
[ 3.347096] calling futex_init+0x0/0xa5 @ 1
[ 3.351429] initcall futex_init+0x0/0xa5 returned 0 after 7 usecs
[ 3.357573] calling proc_dma_init+0x0/0x22 @ 1
[ 3.362168] initcall proc_dma_init+0x0/0x22 returned 0 after 8 usecs
[ 3.368572] calling proc_modules_init+0x0/0x22 @ 1
[ 3.373508] initcall proc_modules_init+0x0/0x22 returned 0 after 4 usecs
[ 3.380254] calling kallsyms_init+0x0/0x25 @ 1
[ 3.384845] initcall kallsyms_init+0x0/0x25 returned 0 after 4 usecs
[ 3.391252] calling crash_save_vmcoreinfo_init+0x0/0x4a0 @ 1
[ 3.397067] initcall crash_save_vmcoreinfo_init+0x0/0x4a0 returned 0 after 15 usecs
[ 3.404790] calling crash_notes_memory_init+0x0/0x3c @ 1
[ 3.410244] initcall crash_notes_memory_init+0x0/0x3c returned 0 after 1 usecs
[ 3.417530] calling init_kprobes+0x0/0x16c @ 1
[ 3.430556] initcall init_kprobes+0x0/0x16c returned 0 after 8245 usecs
[ 3.437221] calling utsname_sysctl_init+0x0/0x14 @ 1
[ 3.442329] initcall utsname_sysctl_init+0x0/0x14 returned 0 after 3 usecs
[ 3.449252] calling init_tracepoints+0x0/0x20 @ 1
[ 3.454096] initcall init_tracepoints+0x0/0x20 returned 0 after 0 usecs
[ 3.460759] calling init_lstats_procfs+0x0/0x34 @ 1
[ 3.465782] initcall init_lstats_procfs+0x0/0x34 returned 0 after 4 usecs
[ 3.472615] calling init_stack_trace+0x0/0x1b @ 1
[ 3.477462] initcall init_stack_trace+0x0/0x1b returned 0 after 1 usecs
[ 3.484125] calling init_per_zone_pages_min+0x0/0x96 @ 1
[ 3.489808] initcall init_per_zone_pages_min+0x0/0x96 returned 0 after 225 usecs
[ 3.497275] calling pdflush_init+0x0/0x12 @ 1
[ 3.501832] initcall pdflush_init+0x0/0x12 returned 0 after 59 usecs
[ 3.508236] calling kswapd_init+0x0/0x14 @ 1
[ 3.512698] initcall kswapd_init+0x0/0x14 returned 0 after 23 usecs
[ 3.519017] calling init_tmpfs+0x0/0xd8 @ 1
[ 3.523388] initcall init_tmpfs+0x0/0xd8 returned 0 after 38 usecs
[ 3.529616] calling setup_vmstat+0x0/0x7c @ 1
[ 3.534129] initcall setup_vmstat+0x0/0x7c returned 0 after 14 usecs
[ 3.540536] calling mm_sysfs_init+0x0/0x29 @ 1
[ 3.545130] initcall mm_sysfs_init+0x0/0x29 returned 0 after 8 usecs
[ 3.551534] calling proc_vmalloc_init+0x0/0x25 @ 1
[ 3.556472] initcall proc_vmalloc_init+0x0/0x25 returned 0 after 5 usecs
[ 3.563225] calling procswaps_init+0x0/0x24 @ 1
[ 3.567902] initcall procswaps_init+0x0/0x24 returned 0 after 4 usecs
[ 3.574397] calling hugetlb_init+0x0/0x478 @ 1
[ 3.578982] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 3.585400] initcall hugetlb_init+0x0/0x478 returned 0 after 6267 usecs
[ 3.592059] calling slab_proc_init+0x0/0x25 @ 1
[ 3.596735] initcall slab_proc_init+0x0/0x25 returned 0 after 4 usecs
[ 3.603222] calling slab_sysfs_init+0x0/0xf8 @ 1
[ 3.619507] initcall slab_sysfs_init+0x0/0xf8 returned 0 after 11251 usecs
[ 3.626443] calling fasync_init+0x0/0x31 @ 1
[ 3.632626] initcall fasync_init+0x0/0x31 returned 0 after 1459 usecs
[ 3.639120] calling proc_filesystems_init+0x0/0x22 @ 1
[ 3.644441] initcall proc_filesystems_init+0x0/0x22 returned 0 after 11 usecs
[ 3.651626] calling dnotify_init+0x0/0x2a @ 1
[ 3.656261] initcall dnotify_init+0x0/0x2a returned 0 after 133 usecs
[ 3.662754] calling aio_setup+0x0/0xb4 @ 1
[ 3.667539] initcall aio_setup+0x0/0xb4 returned 0 after 424 usecs
[ 3.673770] calling proc_locks_init+0x0/0x22 @ 1
[ 3.678590] initcall proc_locks_init+0x0/0x22 returned 0 after 5 usecs
[ 3.685166] calling init_sys32_ioctl+0x0/0x88 @ 1
[ 3.690030] initcall init_sys32_ioctl+0x0/0x88 returned 0 after 19 usecs
[ 3.696779] calling init_mbcache+0x0/0x14 @ 1
[ 3.701279] initcall init_mbcache+0x0/0x14 returned 0 after 1 usecs
[ 3.707595] calling dquot_init+0x0/0xf3 @ 1
[ 3.711918] VFS: Disk quotas dquot_6.5.2
[ 3.716039] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.722600] initcall dquot_init+0x0/0xf3 returned 0 after 10429 usecs
[ 3.729088] calling init_v1_quota_format+0x0/0x12 @ 1
[ 3.734280] initcall init_v1_quota_format+0x0/0x12 returned 0 after 0 usecs
[ 3.741290] calling init_v2_quota_format+0x0/0x14 @ 1
[ 3.746483] initcall init_v2_quota_format+0x0/0x14 returned 0 after 0 usecs
[ 3.753493] calling proc_cmdline_init+0x0/0x22 @ 1
[ 3.758431] initcall proc_cmdline_init+0x0/0x22 returned 0 after 5 usecs
[ 3.765184] calling proc_cpuinfo_init+0x0/0x22 @ 1
[ 3.770122] initcall proc_cpuinfo_init+0x0/0x22 returned 0 after 5 usecs
[ 3.776876] calling proc_devices_init+0x0/0x22 @ 1
[ 3.781815] initcall proc_devices_init+0x0/0x22 returned 0 after 6 usecs
[ 3.788914] calling proc_interrupts_init+0x0/0x22 @ 1
[ 3.794110] initcall proc_interrupts_init+0x0/0x22 returned 0 after 4 usecs
[ 3.801126] calling proc_loadavg_init+0x0/0x22 @ 1
[ 3.806062] initcall proc_loadavg_init+0x0/0x22 returned 0 after 4 usecs
[ 3.812816] calling proc_meminfo_init+0x0/0x22 @ 1
[ 3.817753] initcall proc_meminfo_init+0x0/0x22 returned 0 after 4 usecs
[ 3.824508] calling proc_stat_init+0x0/0x22 @ 1
[ 3.829185] initcall proc_stat_init+0x0/0x22 returned 0 after 4 usecs
[ 3.835679] calling proc_uptime_init+0x0/0x2d @ 1
[ 3.840530] initcall proc_uptime_init+0x0/0x2d returned 0 after 4 usecs
[ 3.847198] calling proc_version_init+0x0/0x22 @ 1
[ 3.852135] initcall proc_version_init+0x0/0x22 returned 0 after 4 usecs
[ 3.858889] calling proc_kmsg_init+0x0/0x25 @ 1
[ 3.863565] initcall proc_kmsg_init+0x0/0x25 returned 0 after 4 usecs
[ 3.870060] calling proc_page_init+0x0/0x42 @ 1
[ 3.874741] initcall proc_page_init+0x0/0x42 returned 0 after 7 usecs
[ 3.881232] calling configfs_init+0x0/0xd6 @ 1
[ 3.885958] initcall configfs_init+0x0/0xd6 returned 0 after 137 usecs
[ 3.892533] calling init_devpts_fs+0x0/0x49 @ 1
[ 3.897236] Created ptmx node in devpts ino 2
[ 3.901643] initcall init_devpts_fs+0x0/0x49 returned 0 after 4330 usecs
[ 3.908393] calling init_dlm+0x0/0xa3 @ 1
[ 3.913033] DLM (built Feb 8 2009 06:53:43) installed
[ 3.918222] initcall init_dlm+0x0/0xa3 returned 0 after 5544 usecs
[ 3.924480] calling init_ext3_fs+0x0/0x72 @ 1
[ 3.929259] initcall init_ext3_fs+0x0/0x72 returned 0 after 276 usecs
[ 3.935754] calling journal_init+0x0/0xea @ 1
[ 3.940841] initcall journal_init+0x0/0xea returned 0 after 536 usecs
[ 3.947332] calling init_ext2_fs+0x0/0x62 @ 1
[ 3.951989] initcall init_ext2_fs+0x0/0x62 returned 0 after 132 usecs
[ 3.958478] calling init_ramfs_fs+0x0/0x12 @ 1
[ 3.963140] initcall init_ramfs_fs+0x0/0x12 returned 0 after 1 usecs
[ 3.969545] calling init_hugetlbfs_fs+0x0/0xad @ 1
[ 3.974626] initcall init_hugetlbfs_fs+0x0/0xad returned 0 after 146 usecs
[ 3.981548] calling init_minix_fs+0x0/0x62 @ 1
[ 3.986287] initcall init_minix_fs+0x0/0x62 returned 0 after 133 usecs
[ 3.992868] calling init_iso9660_fs+0x0/0x72 @ 1
[ 3.997803] initcall init_iso9660_fs+0x0/0x72 returned 0 after 153 usecs
[ 4.004559] calling init_hfsplus_fs+0x0/0x60 @ 1
[ 4.009491] initcall init_hfsplus_fs+0x0/0x60 returned 0 after 156 usecs
[ 4.016242] calling init_nls_cp855+0x0/0x12 @ 1
[ 4.020929] initcall init_nls_cp855+0x0/0x12 returned 0 after 1 usecs
[ 4.027422] calling init_nls_cp860+0x0/0x12 @ 1
[ 4.032093] initcall init_nls_cp860+0x0/0x12 returned 0 after 0 usecs
[ 4.038583] calling init_nls_cp862+0x0/0x12 @ 1
[ 4.043255] initcall init_nls_cp862+0x0/0x12 returned 0 after 0 usecs
[ 4.049747] calling init_nls_cp863+0x0/0x12 @ 1
[ 4.054419] initcall init_nls_cp863+0x0/0x12 returned 0 after 0 usecs
[ 4.060909] calling init_nls_cp865+0x0/0x12 @ 1
[ 4.065582] initcall init_nls_cp865+0x0/0x12 returned 0 after 0 usecs
[ 4.072072] calling init_nls_cp874+0x0/0x12 @ 1
[ 4.076744] initcall init_nls_cp874+0x0/0x12 returned 0 after 0 usecs
[ 4.083234] calling init_nls_cp932+0x0/0x12 @ 1
[ 4.087907] initcall init_nls_cp932+0x0/0x12 returned 0 after 0 usecs
[ 4.094396] calling init_nls_euc_jp+0x0/0x48 @ 1
[ 4.099156] initcall init_nls_euc_jp+0x0/0x48 returned 0 after 0 usecs
[ 4.105733] calling init_nls_cp949+0x0/0x12 @ 1
[ 4.110405] initcall init_nls_cp949+0x0/0x12 returned 0 after 0 usecs
[ 4.116895] calling init_nls_ascii+0x0/0x12 @ 1
[ 4.121567] initcall init_nls_ascii+0x0/0x12 returned 0 after 0 usecs
[ 4.128058] calling init_nls_iso8859_2+0x0/0x12 @ 1
[ 4.133077] initcall init_nls_iso8859_2+0x0/0x12 returned 0 after 0 usecs
[ 4.139914] calling init_nls_iso8859_5+0x0/0x12 @ 1
[ 4.144934] initcall init_nls_iso8859_5+0x0/0x12 returned 0 after 0 usecs
[ 4.151771] calling init_nls_cp1255+0x0/0x12 @ 1
[ 4.156530] initcall init_nls_cp1255+0x0/0x12 returned 0 after 0 usecs
[ 4.163106] calling init_nls_iso8859_13+0x0/0x12 @ 1
[ 4.168213] initcall init_nls_iso8859_13+0x0/0x12 returned 0 after 0 usecs
[ 4.175135] calling init_nls_utf8+0x0/0x26 @ 1
[ 4.179722] initcall init_nls_utf8+0x0/0x26 returned 0 after 0 usecs
[ 4.186125] calling init_smb_fs+0x0/0x72 @ 1
[ 4.190798] initcall init_smb_fs+0x0/0x72 returned 0 after 255 usecs
[ 4.197201] calling init_hpfs_fs+0x0/0x62 @ 1
[ 4.201847] initcall init_hpfs_fs+0x0/0x62 returned 0 after 130 usecs
[ 4.208338] calling init_ufs_fs+0x0/0x62 @ 1
[ 4.212907] initcall init_ufs_fs+0x0/0x62 returned 0 after 131 usecs
[ 4.219310] calling init_romfs_fs+0x0/0x62 @ 1
[ 4.224043] initcall init_romfs_fs+0x0/0x62 returned 0 after 131 usecs
[ 4.230636] calling init_qnx4_fs+0x0/0x70 @ 1
[ 4.235264] QNX4 filesystem 0.2.3 registered.
[ 4.239677] initcall init_qnx4_fs+0x0/0x70 returned 0 after 4436 usecs
[ 4.246258] calling init_adfs_fs+0x0/0x62 @ 1
[ 4.250890] initcall init_adfs_fs+0x0/0x62 returned 0 after 134 usecs
[ 4.257382] calling init_omfs_fs+0x0/0x12 @ 1
[ 4.261906] initcall init_omfs_fs+0x0/0x12 returned 0 after 1 usecs
[ 4.268224] calling init_jfs_fs+0x0/0x1d0 @ 1
[ 4.272998] JFS: nTxBlock = 8192, nTxLock = 65536
[ 4.282599] initcall init_jfs_fs+0x0/0x1d0 returned 0 after 9636 usecs
[ 4.289205] calling init_xfs_fs+0x0/0xce @ 1
[ 4.293667] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 4.305316] SGI XFS Quota Management subsystem
[ 4.309830] initcall init_xfs_fs+0x0/0xce returned 0 after 15782 usecs
[ 4.316412] calling init_befs_fs+0x0/0x8a @ 1
[ 4.320908] BeFS version: 0.9.3
[ 4.324243] initcall init_befs_fs+0x0/0x8a returned 0 after 3255 usecs
[ 4.330823] calling init_btrfs_fs+0x0/0xbc @ 1
[ 4.336775] Btrfs loaded
[ 4.339354] initcall init_btrfs_fs+0x0/0xbc returned 0 after 3745 usecs
[ 4.346134] calling init_gfs2_fs+0x0/0x1ce @ 1
[ 4.351640] GFS2 (built Feb 8 2009 06:53:45) installed
[ 4.356921] initcall init_gfs2_fs+0x0/0x1ce returned 0 after 6061 usecs
[ 4.363628] calling init_lock_dlm+0x0/0x6b @ 1
[ 4.368220] Lock_DLM (built Feb 8 2009 06:53:59) installed
[ 4.373845] initcall init_lock_dlm+0x0/0x6b returned 0 after 5501 usecs
[ 4.380508] calling ipc_init+0x0/0x2f @ 1
[ 4.384661] msgmni has been set to 3996
[ 4.388562] initcall ipc_init+0x0/0x2f returned 0 after 3818 usecs
[ 4.394791] calling ipc_sysctl_init+0x0/0x14 @ 1
[ 4.399554] initcall ipc_sysctl_init+0x0/0x14 returned 0 after 4 usecs
[ 4.406128] calling init_mqueue_fs+0x0/0xbd @ 1
[ 4.410968] initcall init_mqueue_fs+0x0/0xbd returned 0 after 164 usecs
[ 4.417629] calling key_proc_init+0x0/0x5e @ 1
[ 4.422365] initcall key_proc_init+0x0/0x5e returned 0 after 9 usecs
[ 4.428783] calling crypto_algapi_init+0x0/0xd @ 1
[ 4.433722] initcall crypto_algapi_init+0x0/0xd returned 0 after 7 usecs
[ 4.440474] calling chainiv_module_init+0x0/0x12 @ 1
[ 4.445582] initcall chainiv_module_init+0x0/0x12 returned 0 after 2 usecs
[ 4.452504] calling eseqiv_module_init+0x0/0x12 @ 1
[ 4.457523] initcall eseqiv_module_init+0x0/0x12 returned 0 after 0 usecs
[ 4.464360] calling seqiv_module_init+0x0/0x1c @ 1
[ 4.469292] initcall seqiv_module_init+0x0/0x1c returned 0 after 0 usecs
[ 4.476042] calling hmac_module_init+0x0/0x12 @ 1
[ 4.480887] initcall hmac_module_init+0x0/0x12 returned 0 after 0 usecs
[ 4.487551] calling crypto_null_mod_init+0x0/0x80 @ 1
[ 4.492774] alg: No test for cipher_null (cipher_null-generic)
[ 4.498719] alg: No test for digest_null (digest_null-generic)
[ 4.504653] alg: No test for compress_null (compress_null-generic)
[ 4.510891] initcall crypto_null_mod_init+0x0/0x80 returned 0 after 17721 usecs
[ 4.518305] calling md4_mod_init+0x0/0x12 @ 1
[ 4.522853] initcall md4_mod_init+0x0/0x12 returned 0 after 51 usecs
[ 4.529255] calling md5_mod_init+0x0/0x12 @ 1
[ 4.533820] initcall md5_mod_init+0x0/0x12 returned 0 after 44 usecs
[ 4.540227] calling rmd128_mod_init+0x0/0x12 @ 1
[ 4.545061] initcall rmd128_mod_init+0x0/0x12 returned 0 after 51 usecs
[ 4.551727] calling rmd256_mod_init+0x0/0x12 @ 1
[ 4.556546] initcall rmd256_mod_init+0x0/0x12 returned 0 after 48 usecs
[ 4.563211] calling sha1_generic_mod_init+0x0/0x12 @ 1
[ 4.568544] initcall sha1_generic_mod_init+0x0/0x12 returned 0 after 45 usecs
[ 4.575726] calling sha256_generic_mod_init+0x0/0x49 @ 1
[ 4.581282] initcall sha256_generic_mod_init+0x0/0x49 returned 0 after 90 usecs
[ 4.588657] calling wp512_mod_init+0x0/0x80 @ 1
[ 4.593539] initcall wp512_mod_init+0x0/0x80 returned 0 after 197 usecs
[ 4.600200] calling tgr192_mod_init+0x0/0x72 @ 1
[ 4.605114] initcall tgr192_mod_init+0x0/0x72 returned 0 after 139 usecs
[ 4.611867] calling crypto_ecb_module_init+0x0/0x12 @ 1
[ 4.617249] initcall crypto_ecb_module_init+0x0/0x12 returned 0 after 1 usecs
[ 4.624432] calling crypto_cbc_module_init+0x0/0x12 @ 1
[ 4.629798] initcall crypto_cbc_module_init+0x0/0x12 returned 0 after 0 usecs
[ 4.636981] calling crypto_pcbc_module_init+0x0/0x12 @ 1
[ 4.642434] initcall crypto_pcbc_module_init+0x0/0x12 returned 0 after 0 usecs
[ 4.649721] calling crypto_module_init+0x0/0x12 @ 1
[ 4.654740] initcall crypto_module_init+0x0/0x12 returned 0 after 0 usecs
[ 4.661577] calling crypto_ctr_module_init+0x0/0x44 @ 1
[ 4.666944] initcall crypto_ctr_module_init+0x0/0x44 returned 0 after 1 usecs
[ 4.674126] calling crypto_gcm_module_init+0x0/0x62 @ 1
[ 4.679493] initcall crypto_gcm_module_init+0x0/0x62 returned 0 after 1 usecs
[ 4.686675] calling crypto_ccm_module_init+0x0/0x62 @ 1
[ 4.692042] initcall crypto_ccm_module_init+0x0/0x62 returned 0 after 1 usecs
[ 4.699225] calling des_generic_mod_init+0x0/0x44 @ 1
[ 4.704525] initcall des_generic_mod_init+0x0/0x44 returned 0 after 104 usecs
[ 4.711706] calling fcrypt_mod_init+0x0/0x12 @ 1
[ 4.716507] alg: No test for fcrypt (fcrypt-generic)
[ 4.721534] initcall fcrypt_mod_init+0x0/0x12 returned 0 after 4933 usecs
[ 4.728386] calling blowfish_mod_init+0x0/0x12 @ 1
[ 4.733772] initcall blowfish_mod_init+0x0/0x12 returned 0 after 448 usecs
[ 4.740696] calling twofish_mod_init+0x0/0x12 @ 1
[ 4.745624] initcall twofish_mod_init+0x0/0x12 returned 0 after 76 usecs
[ 4.752379] calling serpent_mod_init+0x0/0x44 @ 1
[ 4.757360] initcall serpent_mod_init+0x0/0x44 returned 0 after 117 usecs
[ 4.764200] calling aes_init+0x0/0x12 @ 1
[ 4.768429] initcall aes_init+0x0/0x12 returned 0 after 67 usecs
[ 4.774487] calling camellia_init+0x0/0x12 @ 1
[ 4.779148] initcall camellia_init+0x0/0x12 returned 0 after 59 usecs
[ 4.785641] calling cast5_mod_init+0x0/0x12 @ 1
[ 4.790379] initcall cast5_mod_init+0x0/0x12 returned 0 after 58 usecs
[ 4.796961] calling arc4_init+0x0/0x12 @ 1
[ 4.801613] initcall arc4_init+0x0/0x12 returned 0 after 56 usecs
[ 4.807758] calling khazad_mod_init+0x0/0x12 @ 1
[ 4.812597] initcall khazad_mod_init+0x0/0x12 returned 0 after 70 usecs
[ 4.819259] calling anubis_mod_init+0x0/0x12 @ 1
[ 4.824108] initcall anubis_mod_init+0x0/0x12 returned 0 after 79 usecs
[ 4.830769] calling deflate_mod_init+0x0/0x12 @ 1
[ 4.836009] initcall deflate_mod_init+0x0/0x12 returned 0 after 377 usecs
[ 4.842858] calling michael_mic_init+0x0/0x12 @ 1
[ 4.847760] initcall michael_mic_init+0x0/0x12 returned 0 after 54 usecs
[ 4.854507] calling crc32c_mod_init+0x0/0x12 @ 1
[ 4.859334] initcall crc32c_mod_init+0x0/0x12 returned 0 after 58 usecs
[ 4.865999] calling crypto_authenc_module_init+0x0/0x12 @ 1
[ 4.871719] initcall crypto_authenc_module_init+0x0/0x12 returned 0 after 1 usecs
[ 4.879267] calling krng_mod_init+0x0/0x12 @ 1
[ 4.883878] alg: No test for stdrng (krng)
[ 4.888040] initcall krng_mod_init+0x0/0x12 returned 0 after 4089 usecs
[ 4.894712] calling prng_mod_init+0x0/0x2a @ 1
[ 4.899320] alg: No test for stdrng (ansi_cprng)
[ 4.904010] initcall prng_mod_init+0x0/0x2a returned 0 after 4603 usecs
[ 4.910675] calling proc_genhd_init+0x0/0x3c @ 1
[ 4.915443] initcall proc_genhd_init+0x0/0x3c returned 0 after 9 usecs
[ 4.922020] calling bsg_init+0x0/0x12f @ 1
[ 4.926542] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 4.934008] initcall bsg_init+0x0/0x12f returned 0 after 7567 usecs
[ 4.940331] calling noop_init+0x0/0x14 @ 1
[ 4.944563] io scheduler noop registered (default)
[ 4.949406] initcall noop_init+0x0/0x14 returned 0 after 4729 usecs
[ 4.955724] calling libcrc32c_mod_init+0x0/0x2c @ 1
[ 4.960737] initcall libcrc32c_mod_init+0x0/0x2c returned 0 after 3 usecs
[ 4.967571] calling dynamic_printk_init+0x0/0x101 @ 1
[ 4.973492] initcall dynamic_printk_init+0x0/0x101 returned 0 after 719 usecs
[ 4.980680] calling pci_init+0x0/0x46 @ 1
[ 4.984855] pci 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 4.991170] pci 0000:00:1d.0: Performing full reset
[ 4.996110] pci 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 5.002428] pci 0000:00:1d.1: Performing full reset
[ 5.007375] pci 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 5.013685] pci 0000:00:1d.2: Performing full reset
[ 5.018624] pci 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[ 5.024938] pci 0000:00:1d.3: Performing full reset
[ 5.029927] pci 0000:04:00.0: Boot video device
[ 5.034517] initcall pci_init+0x0/0x46 returned 0 after 48524 usecs
[ 5.040831] calling pci_proc_init+0x0/0x7b @ 1
[ 5.045531] initcall pci_proc_init+0x0/0x7b returned 0 after 120 usecs
[ 5.052107] calling pcie_portdrv_init+0x0/0x50 @ 1
[ 5.057189] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 5.063842] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 5.070625] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 5.077381] initcall pcie_portdrv_init+0x0/0x50 returned 0 after 19864 usecs
[ 5.084490] calling aer_service_init+0x0/0x29 @ 1
[ 5.089416] initcall aer_service_init+0x0/0x29 returned 0 after 83 usecs
[ 5.096168] calling pci_hotplug_init+0x0/0x51 @ 1
[ 5.101044] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.106665] initcall pci_hotplug_init+0x0/0x51 returned 0 after 5487 usecs
[ 5.113587] calling pcied_init+0x0/0x82 @ 1
[ 5.119378] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 5.126044] initcall pcied_init+0x0/0x82 returned 0 after 7947 usecs
[ 5.132476] calling acpiphp_init+0x0/0x65 @ 1
[ 5.136969] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 5.155614] initcall acpiphp_init+0x0/0x65 returned -19 after 18207 usecs
[ 5.162452] calling shpcd_init+0x0/0x68 @ 1
[ 5.166877] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.173632] initcall shpcd_init+0x0/0x68 returned 0 after 6695 usecs
[ 5.180073] calling pci_stub_init+0x0/0x25 @ 1
[ 5.184747] initcall pci_stub_init+0x0/0x25 returned 0 after 89 usecs
[ 5.191242] calling mbp_init+0x0/0xee @ 1
[ 5.195413] initcall mbp_init+0x0/0xee returned -19 after 2 usecs
[ 5.201555] calling pm2fb_init+0x0/0x132 @ 1
[ 5.206054] initcall pm2fb_init+0x0/0x132 returned 0 after 86 usecs
[ 5.212371] calling rivafb_init+0x0/0x1a3 @ 1
[ 5.216889] rivafb_setup START
[ 5.220091] initcall rivafb_init+0x0/0x1a3 returned 0 after 3125 usecs
[ 5.226670] calling atyfb_init+0x0/0x1d0 @ 1
[ 5.231185] initcall atyfb_init+0x0/0x1d0 returned 0 after 84 usecs
[ 5.237504] calling aty128fb_init+0x0/0x120 @ 1
[ 5.242286] initcall aty128fb_init+0x0/0x120 returned 0 after 93 usecs
[ 5.248867] calling sisfb_init+0x0/0x825 @ 1
[ 5.253389] initcall sisfb_init+0x0/0x825 returned 0 after 95 usecs
[ 5.259708] calling viafb_init+0x0/0x1252 @ 1
[ 5.264219] VIA Graphics Intergration Chipset framebuffer 2.4 initializing
[ 5.271196] I2C adapter driver [via_i2c] forgot to specify physical device
[ 5.278213] i2c-adapter i2c-0: adapter [via_i2c] registered
[ 5.283868] i2c-adapter i2c-0: master_xfer[0] W, addr=0x08, len=1
[ 5.290029] i2c-adapter i2c-0: master_xfer[1] R, addr=0x08, len=1
[ 5.376005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 5.540006] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 5.704006] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 5.868005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 5.874062] i2c-adapter i2c-0: Used 4 tries to write to client at 0x08: failed, timeout?
[ 5.882216] i2c-adapter i2c-0: NAK from device addr 0x08 msg #0
[ 5.968047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x08, len=1
[ 5.974186] i2c-adapter i2c-0: master_xfer[1] R, addr=0x08, len=1
[ 6.060005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 6.224005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 6.388004] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 6.552005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 6.558059] i2c-adapter i2c-0: Used 4 tries to write to client at 0x08: failed, timeout?
[ 6.566214] i2c-adapter i2c-0: NAK from device addr 0x08 msg #0
[ 6.652060] i2c-adapter i2c-0: master_xfer[0] W, addr=0x08, len=1
[ 6.658204] i2c-adapter i2c-0: master_xfer[1] R, addr=0x08, len=1
[ 6.744004] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 6.908005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 7.072005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 7.236005] i2c-adapter i2c-0: i2c_outb: 0x10, timeout at bit #7
[ 7.242059] i2c-adapter i2c-0: Used 4 tries to write to client at 0x08: failed, timeout?
[ 7.250214] i2c-adapter i2c-0: NAK from device addr 0x08 msg #0
[ 7.336047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 7.342185] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 7.428005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 7.592005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 7.756005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 7.920005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 7.926059] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 7.934214] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 8.020047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 8.026185] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 8.112005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 8.276006] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 8.440005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 8.604005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 8.610058] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 8.618213] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 8.704047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 8.710192] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 8.796005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 8.960004] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.124005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.288005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.294057] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 9.302212] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 9.388052] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 9.394192] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 9.480005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.644005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.808005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.972004] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 9.978057] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 9.986212] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 10.072047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 10.078192] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 10.164005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 10.328005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 10.492005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 10.656005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 10.662056] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 10.670212] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 10.756047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
[ 10.762191] i2c-adapter i2c-0: master_xfer[1] R, addr=0x50, len=1
[ 10.848005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 11.012004] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 11.176005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 11.340005] i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
[ 11.346055] i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
[ 11.354211] i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
[ 11.440047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x40, len=1
[ 11.446190] i2c-adapter i2c-0: master_xfer[1] R, addr=0x40, len=1
[ 11.532004] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 11.696005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 11.860005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.024004] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.030056] i2c-adapter i2c-0: Used 4 tries to write to client at 0x40: failed, timeout?
[ 12.038211] i2c-adapter i2c-0: NAK from device addr 0x40 msg #0
[ 12.124047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x40, len=1
[ 12.130190] i2c-adapter i2c-0: master_xfer[1] R, addr=0x40, len=1
[ 12.216005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.380005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.544005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.708005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 12.714409] i2c-adapter i2c-0: Used 4 tries to write to client at 0x40: failed, timeout?
[ 12.722564] i2c-adapter i2c-0: NAK from device addr 0x40 msg #0
[ 12.808047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x40, len=1
[ 12.814189] i2c-adapter i2c-0: master_xfer[1] R, addr=0x40, len=1
[ 12.900005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.064005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.228004] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.392005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.398062] i2c-adapter i2c-0: Used 4 tries to write to client at 0x40: failed, timeout?
[ 13.406218] i2c-adapter i2c-0: NAK from device addr 0x40 msg #0
[ 13.492046] i2c-adapter i2c-0: master_xfer[0] W, addr=0x40, len=1
[ 13.498188] i2c-adapter i2c-0: master_xfer[1] R, addr=0x40, len=1
[ 13.584005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.748005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 13.912005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 14.076005] i2c-adapter i2c-0: i2c_outb: 0x80, timeout at bit #7
[ 14.082062] i2c-adapter i2c-0: Used 4 tries to write to client at 0x40: failed, timeout?
[ 14.090217] i2c-adapter i2c-0: NAK from device addr 0x40 msg #0
[ 14.176047] i2c-adapter i2c-0: master_xfer[0] W, addr=0x38, len=1
[ 14.182187] i2c-adapter i2c-0: master_xfer[1] R, addr=0x38, len=1
[ 14.268005] i2c-adapter i2c-0: i2c_outb: 0x70, timeout at bit #7
[ 14.432005] i2c-adapter i2c-0: i2c_outb: 0x70, timeout at bit #7
[ 14.596005] i2c-adapter i2c-0: i2c_outb: 0x70, timeout at bit #7
[ 14.760005] i2c-adapter i2c-0: i2c_outb: 0x70, timeout at bit #7
[ 14.766061] i2c-adapter i2c-0: Used 4 tries to write to client at 0x38: failed, timeout?
[ 14.774217] i2c-adapter i2c-0: NAK from device addr 0x38 msg #0
[ 14.860050] ioremap failed
[ 14.862803] initcall viafb_init+0x0/0x1252 returned -1 after 9373618 usecs
[ 14.869725] initcall viafb_init+0x0/0x1252 returned with error code -1
[ 14.876389] calling tdfxfb_init+0x0/0x11e @ 1
[ 14.880990] initcall tdfxfb_init+0x0/0x11e returned 0 after 99 usecs
[ 14.887397] calling imsttfb_init+0x0/0x131 @ 1
[ 14.892073] initcall imsttfb_init+0x0/0x131 returned 0 after 88 usecs
[ 14.898559] calling vt8623fb_init+0x0/0x98 @ 1
[ 14.903254] initcall vt8623fb_init+0x0/0x98 returned 0 after 97 usecs
[ 14.909748] calling s3fb_init+0x0/0xfe @ 1
[ 14.914092] initcall s3fb_init+0x0/0xfe returned 0 after 93 usecs
[ 14.920235] calling hecubafb_init+0x0/0x12 @ 1
[ 14.924918] initcall hecubafb_init+0x0/0x12 returned 0 after 84 usecs
[ 14.931406] calling tmiofb_init+0x0/0x6b @ 1
[ 14.935912] initcall tmiofb_init+0x0/0x6b returned 0 after 79 usecs
[ 14.942231] calling mb862xxfb_init+0x0/0xb @ 1
[ 14.946829] initcall mb862xxfb_init+0x0/0xb returned -19 after 0 usecs
[ 14.953411] calling acpi_reserve_resources+0x0/0xeb @ 1
[ 14.958782] initcall acpi_reserve_resources+0x0/0xeb returned 0 after 5 usecs
[ 14.965970] calling acpi_ac_init+0x0/0x28 @ 1
[ 14.970577] initcall acpi_ac_init+0x0/0x28 returned 0 after 107 usecs
[ 14.977071] calling acpi_battery_init+0x0/0x28 @ 1
[ 14.982108] initcall acpi_battery_init+0x0/0x28 returned 0 after 90 usecs
[ 14.988944] calling acpi_button_init+0x0/0x5e @ 1
[ 14.993986] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 15.001885] ACPI: Power Button (FF) [PWRF]
[ 15.006206] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 15.014883] ACPI: Power Button (CM) [PWRB]
[ 15.019119] initcall acpi_button_init+0x0/0x5e returned 0 after 24723 usecs
[ 15.026134] calling acpi_fan_init+0x0/0x5e @ 1
[ 15.030826] initcall acpi_fan_init+0x0/0x5e returned 0 after 94 usecs
[ 15.037314] calling irqrouter_init_sysfs+0x0/0x38 @ 1
[ 15.042678] initcall irqrouter_init_sysfs+0x0/0x38 returned 0 after 157 usecs
[ 15.049862] calling acpi_processor_init+0x0/0xad @ 1
[ 15.055933] processor ACPI_CPU:00: registered as cooling_device0
[ 15.062000] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 15.068433] initcall acpi_processor_init+0x0/0xad returned 0 after 13137 usecs
[ 15.075726] calling rand_initialize+0x0/0x30 @ 1
[ 15.080509] initcall rand_initialize+0x0/0x30 returned 0 after 13 usecs
[ 15.087172] calling tty_init+0x0/0xfa @ 1
[ 15.128250] initcall tty_init+0x0/0xfa returned 0 after 36056 usecs
[ 15.134578] calling pty_init+0x0/0x3cb @ 1
[ 15.139022] initcall pty_init+0x0/0x3cb returned 0 after 146 usecs
[ 15.145258] calling sysrq_init+0x0/0x25 @ 1
[ 15.149620] initcall sysrq_init+0x0/0x25 returned 0 after 16 usecs
[ 15.155847] calling cy_init+0x0/0x16b @ 1
[ 15.160000] Cyclades driver 2.5 (built Feb 8 2009 06:54:01)
[ 15.165840] initcall cy_init+0x0/0x16b returned 0 after 5702 usecs
[ 15.172072] calling istallion_module_init+0x0/0x560 @ 1
[ 15.177445] Stallion Intelligent Multiport Serial Driver: version 5.6.0
[ 15.184682] initcall istallion_module_init+0x0/0x560 returned 0 after 7065 usecs
[ 15.192144] calling epca_module_init+0x0/0x501 @ 1
[ 15.197086] DIGI epca driver version 1.3.0.1-LK2.6 loaded.
[ 15.278321] initcall epca_module_init+0x0/0x501 returned 0 after 79324 usecs
[ 15.285682] calling specialix_init_module+0x0/0x45d @ 1
[ 15.291336] sx: Specialix IO8+ driver v1.11, (c) R.E.Wolff 1997/1998.
[ 15.297866] sx: derived from work (c) D.Gorodchanin 1994-1996.
[ 15.303750] sx: DTR/RTS pin is always RTS.
[ 15.319040] sx0: specialix IO8+ Board at 0x100 not found.
[ 15.324514] sx1: specialix IO8+ Board at 0x180 not found.
[ 15.330280] sx2: specialix IO8+ Board at 0x250 not found.
[ 15.335985] sx3: specialix IO8+ Board at 0x260 not found.
[ 15.351760] sx: No specialix IO8+ boards detected.
[ 15.356624] initcall specialix_init_module+0x0/0x45d returned -5 after 63749 usecs
[ 15.364495] initcall specialix_init_module+0x0/0x45d returned with error code -5
[ 15.372292] calling isicom_init+0x0/0x21f @ 1
[ 15.376954] initcall isicom_init+0x0/0x21f returned 0 after 150 usecs
[ 15.383443] calling synclink_init+0x0/0x294 @ 1
[ 15.388217] SyncLink serial driver $Revision: 4.38 $
[ 15.415174] SyncLink serial driver $Revision: 4.38 $, tty major#252
[ 15.421749] initcall synclink_init+0x0/0x294 returned 0 after 32740 usecs
[ 15.428830] calling sx_init+0x0/0x120 @ 1
[ 15.433262] initcall sx_init+0x0/0x120 returned 0 after 261 usecs
[ 15.439405] calling rio_init+0x0/0x12d6 @ 1
[ 15.445805] initcall rio_init+0x0/0x12d6 returned -5 after 1962 usecs
[ 15.452301] initcall rio_init+0x0/0x12d6 returned with error code -5
[ 15.458829] calling raw_init+0x0/0xea @ 1
[ 15.463192] initcall raw_init+0x0/0xea returned 0 after 210 usecs
[ 15.469339] calling applicom_init+0x0/0x4ff @ 1
[ 15.474118] Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $
[ 15.481418] ac.o: No PCI boards found.
[ 15.485223] ac.o: For an ISA board you must supply memory and irq parameters.
[ 15.492410] initcall applicom_init+0x0/0x4ff returned -6 after 17860 usecs
[ 15.499333] initcall applicom_init+0x0/0x4ff returned with error code -6
[ 15.506171] calling hpet_init+0x0/0x6d @ 1
[ 15.510656] initcall hpet_init+0x0/0x6d returned 0 after 240 usecs
[ 15.516884] calling nvram_init+0x0/0x94 @ 1
[ 15.521357] Non-volatile memory driver v1.3
[ 15.525595] initcall nvram_init+0x0/0x94 returned 0 after 4263 usecs
[ 15.532096] calling agp_init+0x0/0x38 @ 1
[ 15.536243] Linux agpgart interface v0.103
[ 15.540387] initcall agp_init+0x0/0x38 returned 0 after 4045 usecs
[ 15.546618] calling agp_intel_init+0x0/0x2c @ 1
[ 15.551423] initcall agp_intel_init+0x0/0x2c returned 0 after 129 usecs
[ 15.558085] calling agp_sis_init+0x0/0x2c @ 1
[ 15.562688] initcall agp_sis_init+0x0/0x2c returned 0 after 86 usecs
[ 15.569091] calling ipmi_init_msghandler_mod+0x0/0xd @ 1
[ 15.574644] ipmi message handler version 39.2
[ 15.579058] initcall ipmi_init_msghandler_mod+0x0/0xd returned 0 after 4390 usecs
[ 15.586623] calling init_ipmi_devintf+0x0/0x107 @ 1
[ 15.591640] ipmi device interface
[ 15.595091] initcall init_ipmi_devintf+0x0/0x107 returned 0 after 3368 usecs
[ 15.602192] calling init_ipmi_si+0x0/0x88b @ 1
[ 15.606873] IPMI System Interface driver.
[ 15.660196] ipmi_si: Unable to find any System Interface(s)
[ 15.665821] initcall init_ipmi_si+0x0/0x88b returned -19 after 57647 usecs
[ 15.672745] calling hangcheck_init+0x0/0x93 @ 1
[ 15.677415] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
[ 15.686436] Hangcheck: Using get_cycles().
[ 15.690581] initcall hangcheck_init+0x0/0x93 returned 0 after 12856 usecs
[ 15.697417] calling intelfb_init+0x0/0x230 @ 1
[ 15.702002] intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/945GME/965G/965GM chipsets
[ 15.713623] intelfb: Version 0.9.6
[ 15.717171] initcall intelfb_init+0x0/0x230 returned 0 after 14812 usecs
[ 15.723921] calling serial8250_init+0x0/0x136 @ 1
[ 15.728786] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 15.735280] async_waiting @ 1
[ 15.738299] async_continuing @ 1 after 0 usec
[ 15.868096] async_waiting @ 1
[ 15.871108] async_continuing @ 1 after 0 usec
[ 16.000128] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 16.006968] initcall serial8250_init+0x0/0x136 returned 0 after 271661 usecs
[ 16.014065] calling parport_default_proc_register+0x0/0x20 @ 1
[ 16.020041] initcall parport_default_proc_register+0x0/0x20 returned 0 after 4 usecs
[ 16.027851] calling parport_pc_init+0x0/0x41f @ 1
[ 16.033042] parport_pc 00:07: reported by Plug and Play ACPI
[ 16.038858] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 16.144861] initcall parport_pc_init+0x0/0x41f returned 0 after 109543 usecs
[ 16.151959] calling floppy_init+0x0/0x125f @ 1
[ 16.156619] Floppy drive(s): fd0 is 1.44M
[ 16.179649] FDC 0 is a post-1991 82077
[ 16.184662] initcall floppy_init+0x0/0x125f returned 0 after 27458 usecs
[ 16.191409] calling brd_init+0x0/0x1cc @ 1
[ 16.199331] brd: module loaded
[ 16.202481] initcall brd_init+0x0/0x1cc returned 0 after 6677 usecs
[ 16.208796] calling cpqarray_init+0x0/0x2c7 @ 1
[ 16.213465] Compaq SMART2 Driver (v 2.6.0)
[ 16.217802] initcall cpqarray_init+0x0/0x2c7 returned -19 after 4232 usecs
[ 16.224725] calling pkt_init+0x0/0x1cd @ 1
[ 16.229658] initcall pkt_init+0x0/0x1cd returned 0 after 328 usecs
[ 16.235887] calling carm_init+0x0/0x1b @ 1
[ 16.240867] initcall carm_init+0x0/0x1b returned 0 after 520 usecs
[ 16.247103] calling wm8400_module_init+0x0/0x38 @ 1
[ 16.252235] i2c-core: driver [WM8400] registered
[ 16.256907] initcall wm8400_module_init+0x0/0x38 returned 0 after 4647 usecs
[ 16.264079] calling pcf50633_init+0x0/0x1e @ 1
[ 16.268745] i2c-core: driver [pcf50633] registered
[ 16.273589] initcall pcf50633_init+0x0/0x1e returned 0 after 4808 usecs
[ 16.280274] calling e1000_init_module+0x0/0x70 @ 1
[ 16.285199] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
[ 16.291343] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 16.297327] initcall e1000_init_module+0x0/0x70 returned 0 after 11842 usecs
[ 16.304423] calling ixgbe_init_module+0x0/0x5a @ 1
[ 16.309385] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 1.3.30-k2
[ 16.317283] ixgbe: Copyright (c) 1999-2007 Intel Corporation.
[ 16.323178] initcall ixgbe_init_module+0x0/0x5a returned 0 after 13468 usecs
[ 16.330275] calling t1_init_module+0x0/0x1b @ 1
[ 16.335049] initcall t1_init_module+0x0/0x1b returned 0 after 86 usecs
[ 16.341630] calling vcan_init_module+0x0/0x3a @ 1
[ 16.346487] vcan: Virtual CAN interface driver
[ 16.350982] initcall vcan_init_module+0x0/0x3a returned 0 after 4388 usecs
[ 16.357904] calling jme_init_module+0x0/0x30 @ 1
[ 16.362662] jme: JMicron JMC250 gigabit ethernet driver version 1.0.3
[ 16.369246] initcall jme_init_module+0x0/0x30 returned 0 after 6428 usecs
[ 16.376088] calling rr_init_module+0x0/0x1b @ 1
[ 16.380861] initcall rr_init_module+0x0/0x1b returned 0 after 85 usecs
[ 16.387441] calling gem_init+0x0/0x1b @ 1
[ 16.391695] initcall gem_init+0x0/0x1b returned 0 after 85 usecs
[ 16.397754] calling vortex_init+0x0/0xc3 @ 1
[ 16.402268] initcall vortex_init+0x0/0xc3 returned 0 after 86 usecs
[ 16.408588] calling e100_init_module+0x0/0x5f @ 1
[ 16.413446] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
[ 16.419584] e100: Copyright(c) 1999-2006 Intel Corporation
[ 16.425211] initcall e100_init_module+0x0/0x5f returned 0 after 11488 usecs
[ 16.432222] calling ns83820_init+0x0/0x29 @ 1
[ 16.436732] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
[ 16.443656] initcall ns83820_init+0x0/0x29 returned 0 after 6760 usecs
[ 16.450231] calling tg3_init+0x0/0x1b @ 1
[ 16.454487] initcall tg3_init+0x0/0x1b returned 0 after 87 usecs
[ 16.460545] calling bnx2x_init+0x0/0x55 @ 1
[ 16.465010] initcall bnx2x_init+0x0/0x55 returned 0 after 123 usecs
[ 16.471325] calling skge_init_module+0x0/0x1b @ 1
[ 16.476266] initcall skge_init_module+0x0/0x1b returned 0 after 87 usecs
[ 16.483017] calling sky2_init_module+0x0/0x29 @ 1
[ 16.487874] sky2 driver version 1.22
[ 16.491540] sky2 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 16.498387] sky2 0000:02:00.0: setting latency timer to 64
[ 16.503962] sky2 0000:02:00.0: Yukon-2 EC chip revision 2
[ 16.541275] sky2 0000:02:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
[ 16.548735] Part Number: Yukon 88E8053
[ 16.552617] Engineering Level: Rev. 1.9
[ 16.556586] Manufacturer: Marvell
[ 16.560324] sky2 eth0: addr 00:15:f2:e6:8e:6b
[ 16.564821] initcall sky2_init_module+0x0/0x29 returned 0 after 75141 usecs
[ 16.571846] calling starfire_init+0x0/0x1c @ 1
[ 16.576517] initcall starfire_init+0x0/0x1c returned 0 after 86 usecs
[ 16.583004] calling cicada_init+0x0/0x44 @ 1
[ 16.587593] initcall cicada_init+0x0/0x44 returned 0 after 168 usecs
[ 16.593995] calling vsc82xx_init+0x0/0x44 @ 1
[ 16.598678] initcall vsc82xx_init+0x0/0x44 returned 0 after 160 usecs
[ 16.605166] calling realtek_init+0x0/0x12 @ 1
[ 16.609767] initcall realtek_init+0x0/0x12 returned 0 after 81 usecs
[ 16.616172] calling fixed_mdio_bus_init+0x0/0xce @ 1
[ 16.621504] Fixed MDIO Bus: probed
[ 16.624961] initcall fixed_mdio_bus_init+0x0/0xce returned 0 after 3573 usecs
[ 16.632160] calling ns_init+0x0/0x12 @ 1
[ 16.636301] initcall ns_init+0x0/0x12 returned 0 after 80 usecs
[ 16.642266] calling sundance_init+0x0/0x21 @ 1
[ 16.646957] initcall sundance_init+0x0/0x21 returned 0 after 86 usecs
[ 16.653447] calling net_olddevs_init+0x0/0xae @ 1
[ 16.658427] initcall net_olddevs_init+0x0/0xae returned 0 after 118 usecs
[ 16.665268] calling init_nic+0x0/0x1b @ 1
[ 16.669509] initcall init_nic+0x0/0x1b returned 0 after 88 usecs
[ 16.675564] calling ppp_init+0x0/0xa7 @ 1
[ 16.679730] PPP generic driver version 2.4.2
[ 16.684301] initcall ppp_init+0x0/0xa7 returned 0 after 4462 usecs
[ 16.690531] calling ppp_mppe_init+0x0/0x117 @ 1
[ 16.695392] PPP MPPE Compression module registered
[ 16.700239] initcall ppp_mppe_init+0x0/0x117 returned 0 after 4905 usecs
[ 16.707013] calling macvlan_init_module+0x0/0x56 @ 1
[ 16.712116] initcall macvlan_init_module+0x0/0x56 returned 0 after 3 usecs
[ 16.719037] calling rtl8139_init_module+0x0/0x1b @ 1
[ 16.724261] initcall rtl8139_init_module+0x0/0x1b returned 0 after 117 usecs
[ 16.731361] calling rio_init+0x0/0x1b @ 1
[ 16.735624] initcall rio_init+0x0/0x1b returned 0 after 87 usecs
[ 16.741682] calling mlx4_init+0x0/0x79 @ 1
[ 16.746068] initcall mlx4_init+0x0/0x79 returned 0 after 125 usecs
[ 16.752299] calling mlx4_en_init+0x0/0x17 @ 1
[ 16.756813] initcall mlx4_en_init+0x0/0x17 returned 0 after 0 usecs
[ 16.763132] calling hdlc_module_init+0x0/0x45 @ 1
[ 16.767977] HDLC support module revision 1.22
[ 16.772389] initcall hdlc_module_init+0x0/0x45 returned 0 after 4307 usecs
[ 16.779312] calling mod_init+0x0/0x14 @ 1
[ 16.783456] initcall mod_init+0x0/0x14 returned 0 after 0 usecs
[ 16.789425] calling fst_init+0x0/0x37 @ 1
[ 16.793665] initcall fst_init+0x0/0x37 returned 0 after 92 usecs
[ 16.799722] calling kaweth_init+0x0/0x1b @ 1
[ 16.804235] usbcore: registered new interface driver kaweth
[ 16.809857] initcall kaweth_init+0x0/0x1b returned 0 after 5574 usecs
[ 16.816361] calling pegasus_init+0x0/0x18d @ 1
[ 16.820938] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 16.828568] usbcore: registered new interface driver pegasus
[ 16.834280] initcall pegasus_init+0x0/0x18d returned 0 after 13028 usecs
[ 16.841042] calling ipw_init+0x0/0x8e @ 1
[ 16.845187] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2km
[ 16.852285] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 16.858173] initcall ipw_init+0x0/0x8e returned 0 after 12679 usecs
[ 16.864489] calling ieee80211_init+0x0/0x24 @ 1
[ 16.869173] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 16.875832] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
[ 16.884249] initcall ieee80211_init+0x0/0x24 returned 0 after 14721 usecs
[ 16.891087] calling airo_init_module+0x0/0xf4 @ 1
[ 16.895940] airo(): Probing for PCI adapters
[ 16.900361] airo(): Finished probing for PCI adapters
[ 16.905466] initcall airo_init_module+0x0/0xf4 returned 0 after 9310 usecs
[ 16.912403] calling prism54_module_init+0x0/0x3c @ 1
[ 16.917502] Loaded prism54 driver, version 1.2
[ 16.922088] initcall prism54_module_init+0x0/0x3c returned 0 after 4477 usecs
[ 16.929272] calling init_netconsole+0x0/0x214 @ 1
[ 16.934131] console [netcon0] enabled
[ 16.937843] netconsole: network logging started
[ 16.942420] initcall init_netconsole+0x0/0x214 returned 0 after 8095 usecs
[ 16.949343] calling efx_init_module+0x0/0xcb @ 1
[ 16.954092] Solarflare NET driver v2.3
[ 16.958035] initcall efx_init_module+0x0/0xcb returned 0 after 3848 usecs
[ 16.964875] calling dabusb_init+0x0/0xd2 @ 1
[ 16.969383] usbcore: registered new interface driver dabusb
[ 16.975006] dabusb: v1.54:DAB-USB Interface Driver for Linux (c)1999
[ 16.981425] initcall dabusb_init+0x0/0xd2 returned 0 after 11841 usecs
[ 16.988006] calling spi_transport_init+0x0/0x30 @ 1
[ 16.993186] initcall spi_transport_init+0x0/0x30 returned 0 after 157 usecs
[ 17.000201] calling fc_transport_init+0x0/0x4e @ 1
[ 17.005461] initcall fc_transport_init+0x0/0x4e returned 0 after 309 usecs
[ 17.012385] calling iscsi_transport_init+0x0/0x153 @ 1
[ 17.017683] Loading iSCSI transport class v2.0-870.
[ 17.023059] initcall iscsi_transport_init+0x0/0x153 returned 0 after 5248 usecs
[ 17.030440] calling scsi_dh_init+0x0/0x42 @ 1
[ 17.034977] initcall scsi_dh_init+0x0/0x42 returned 0 after 1 usecs
[ 17.041298] calling hp_sw_init+0x0/0x12 @ 1
[ 17.045622] hp_sw: device handler registered
[ 17.049937] initcall hp_sw_init+0x0/0x12 returned 0 after 4214 usecs
[ 17.056342] calling iscsi_sw_tcp_init+0x0/0x52 @ 1
[ 17.061401] iscsi: registered transport (tcp)
[ 17.065809] initcall iscsi_sw_tcp_init+0x0/0x52 returned 0 after 4427 usecs
[ 17.072869] calling BusLogic_init+0x0/0x1b3c @ 1
[ 17.077684] initcall BusLogic_init+0x0/0x1b3c returned 0 after 53 usecs
[ 17.084345] calling ahc_linux_init+0x0/0x67 @ 1
[ 17.089123] initcall ahc_linux_init+0x0/0x67 returned 0 after 102 usecs
[ 17.095785] calling ahd_linux_init+0x0/0x83 @ 1
[ 17.100586] initcall ahd_linux_init+0x0/0x83 returned 0 after 107 usecs
[ 17.107251] calling aac_init+0x0/0x7f @ 1
[ 17.111424] Adaptec aacraid driver 1.1-5[2456]-ms
[ 17.116282] initcall aac_init+0x0/0x7f returned 0 after 4743 usecs
[ 17.122513] calling qla1280_init+0x0/0x1b @ 1
[ 17.127124] initcall qla1280_init+0x0/0x1b returned 0 after 94 usecs
[ 17.133529] calling qla4xxx_module_init+0x0/0x14d @ 1
[ 17.139039] iscsi: registered transport (qla4xxx)
[ 17.143892] QLogic iSCSI HBA Driver
[ 17.147445] initcall qla4xxx_module_init+0x0/0x14d returned 0 after 8503 usecs
[ 17.154736] calling lpfc_init+0x0/0xdf @ 1
[ 17.158972] Emulex LightPulse Fibre Channel SCSI driver 8.3.0
[ 17.164770] Copyright(c) 2004-2008 Emulex. All rights reserved.
[ 17.170930] initcall lpfc_init+0x0/0xdf returned 0 after 11675 usecs
[ 17.177329] calling dc390_module_init+0x0/0xa0 @ 1
[ 17.182281] DC390: clustering now enabled by default. If you get problems load
[ 17.189566] with "disable_clustering=1" and report to maintainers
[ 17.196415] initcall dc390_module_init+0x0/0xa0 returned 0 after 13800 usecs
[ 17.203512] calling mraid_mm_init+0x0/0x8c @ 1
[ 17.208117] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 17.215640] initcall mraid_mm_init+0x0/0x8c returned 0 after 7345 usecs
[ 17.222302] calling megasas_init+0x0/0x172 @ 1
[ 17.227246] megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
[ 17.233231] initcall megasas_init+0x0/0x172 returned 0 after 5843 usecs
[ 17.239895] calling gdth_init+0x0/0xf7 @ 1
[ 17.244148] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 17.250388] initcall gdth_init+0x0/0xf7 returned 0 after 6093 usecs
[ 17.256708] calling twa_init+0x0/0x30 @ 1
[ 17.260872] 3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
[ 17.268354] initcall twa_init+0x0/0x30 returned 0 after 7305 usecs
[ 17.274588] calling ppa_driver_init+0x0/0x27 @ 1
[ 17.279358] ppa: Version 2.07 (for Linux 2.4.x)
[ 17.286107] initcall ppa_driver_init+0x0/0x27 returned 0 after 6591 usecs
[ 17.292943] calling imm_driver_init+0x0/0x27 @ 1
[ 17.297699] imm: Version 2.05 (for Linux 2.4.0)
[ 17.302618] initcall imm_driver_init+0x0/0x27 returned 0 after 4802 usecs
[ 17.309454] calling stex_init+0x0/0x33 @ 1
[ 17.313689] stex: Promise SuperTrak EX Driver version: 3.6.0000.1
[ 17.319926] initcall stex_init+0x0/0x33 returned 0 after 6089 usecs
[ 17.326241] calling init_st+0x0/0x1c8 @ 1
[ 17.330404] st: Version 20081215, fixed bufsize 32768, s/g segs 256
[ 17.336801] Driver 'st' needs updating - please use bus_type methods
[ 17.343295] initcall init_st+0x0/0x1c8 returned 0 after 12587 usecs
[ 17.349628] calling init_osst+0x0/0x14b @ 1
[ 17.353948] osst :I: Tape driver with OnStream support version 0.99.4
[ 17.353949] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 17.367265] Driver 'osst' needs updating - please use bus_type methods
[ 17.373935] initcall init_osst+0x0/0x14b returned 0 after 19517 usecs
[ 17.380437] calling init_sd+0x0/0x10d @ 1
[ 17.384676] Driver 'sd' needs updating - please use bus_type methods
[ 17.391158] initcall init_sd+0x0/0x10d returned 0 after 6418 usecs
[ 17.397407] calling init_sr+0x0/0x4e @ 1
[ 17.401467] Driver 'sr' needs updating - please use bus_type methods
[ 17.407955] initcall init_sr+0x0/0x4e returned 0 after 6335 usecs
[ 17.414095] calling init_ch_module+0x0/0xae @ 1
[ 17.418786] SCSI Media Changer driver v0.25
[ 17.423190] Driver 'ch' needs updating - please use bus_type methods
[ 17.429672] initcall init_ch_module+0x0/0xae returned 0 after 10629 usecs
[ 17.436529] calling ahci_init+0x0/0x1b @ 1
[ 17.440870] initcall ahci_init+0x0/0x1b returned 0 after 105 usecs
[ 17.447098] calling k2_sata_init+0x0/0x1b @ 1
[ 17.451700] initcall k2_sata_init+0x0/0x1b returned 0 after 88 usecs
[ 17.458104] calling piix_init+0x0/0x29 @ 1
[ 17.462384] ata_piix 0000:00:1f.1: version 2.12
[ 17.466986] alloc irq_desc for 22 on cpu 0 node 0
[ 17.470965] alloc kstat_irqs on cpu 0 node 0
[ 17.476412] IOAPIC[0]: Set routing entry (2-22 -> 0x59 -> IRQ 22 Mode:1 Active:1)
[ 17.483966] ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 17.491190] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 17.497163] scsi0 : ata_piix
[ 17.500630] scsi1 : ata_piix
[ 17.512401] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 17.519411] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 17.688305] ata1.00: unsupported CDB len
[ 22.844294] ata1.00: unsupported CDB len
[ 22.848267] ata1.00: revalidation failed (errno=-22)
[ 22.853276] ata1.00: disabled
[ 22.856299] async_waiting @ 1
[ 22.859311] async_continuing @ 1 after 0 usec
[ 22.863723] async_waiting @ 1
[ 22.866744] async_continuing @ 1 after 0 usec
[ 23.034136] async_waiting @ 1
[ 23.037158] async_continuing @ 1 after 0 usec
[ 23.041581] alloc irq_desc for 23 on cpu 0 node 0
[ 23.045557] alloc kstat_irqs on cpu 0 node 0
[ 23.051000] IOAPIC[0]: Set routing entry (2-23 -> 0x61 -> IRQ 23 Mode:1 Active:1)
[ 23.058547] ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[ 23.065733] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 23.071177] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 23.077127] scsi2 : ata_piix
[ 23.080309] scsi3 : ata_piix
[ 23.083441] ata3: SATA max UDMA/133 cmd 0x9800 ctl 0x9400 bmdma 0x8400 irq 23
[ 23.090632] ata4: SATA max UDMA/133 cmd 0x9000 ctl 0x8800 bmdma 0x8408 irq 23
[ 23.295428] ata3.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 23.301136] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 23.370406] ata3.00: configured for UDMA/133
[ 23.374728] async_waiting @ 1
[ 23.377750] async_continuing @ 1 after 0 usec
[ 23.382196] isa bounce pool size: 16 pages
[ 23.386469] scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 23.395026] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 23.402774] sd 2:0:0:0: [sda] Write Protect is off
[ 23.407615] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.412796] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 23.422014] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 23.429759] sd 2:0:0:0: [sda] Write Protect is off
[ 23.434603] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.439758] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 23.448870] sda: sda1 sda2 sda3 sda4 < sda5 >
[ 23.494219] sd 2:0:0:0: [sda] Attached SCSI disk
[ 23.499254] async_waiting @ 1
[ 23.502274] async_continuing @ 1 after 0 usec
[ 23.670154] async_waiting @ 1
[ 23.673169] async_continuing @ 1 after 0 usec
[ 23.677685] initcall piix_init+0x0/0x29 returned 0 after 6069643 usecs
[ 23.684266] calling sil_init+0x0/0x1b @ 1
[ 23.688532] initcall sil_init+0x0/0x1b returned 0 after 113 usecs
[ 23.694674] calling sil24_init+0x0/0x1b @ 1
[ 23.699099] initcall sil24_init+0x0/0x1b returned 0 after 88 usecs
[ 23.705333] calling svia_init+0x0/0x1b @ 1
[ 23.709681] initcall svia_init+0x0/0x1b returned 0 after 97 usecs
[ 23.715828] calling sis_init+0x0/0x1b @ 1
[ 23.720094] initcall sis_init+0x0/0x1b returned 0 after 99 usecs
[ 23.726150] calling nv_init+0x0/0x1b @ 1
[ 23.730326] initcall nv_init+0x0/0x1b returned 0 after 96 usecs
[ 23.736298] calling inic_init+0x0/0x1b @ 1
[ 23.740640] initcall inic_init+0x0/0x1b returned 0 after 87 usecs
[ 23.746785] calling amd_init+0x0/0x1b @ 1
[ 23.751039] initcall amd_init+0x0/0x1b returned 0 after 87 usecs
[ 23.757099] calling artop_init+0x0/0x1b @ 1
[ 23.761526] initcall artop_init+0x0/0x1b returned 0 after 87 usecs
[ 23.767758] calling cmd64x_init+0x0/0x1b @ 1
[ 23.772272] initcall cmd64x_init+0x0/0x1b returned 0 after 86 usecs
[ 23.778591] calling hpt3x2n_init+0x0/0x1b @ 1
[ 23.783195] initcall hpt3x2n_init+0x0/0x1b returned 0 after 90 usecs
[ 23.789599] calling it821x_init+0x0/0x1b @ 1
[ 23.794056] alloc irq_desc for 20 on cpu 0 node 0
[ 23.798006] alloc kstat_irqs on cpu 0 node 0
[ 23.803476] IOAPIC[0]: Set routing entry (2-20 -> 0x69 -> IRQ 20 Mode:1 Active:1)
[ 23.811024] pata_it821x 0000:01:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 23.818486] pata_it821x: controller in pass through mode.
[ 23.823965] pata_it821x 0000:01:03.0: setting latency timer to 64
[ 23.830198] scsi4 : pata_it821x
[ 23.833648] scsi5 : pata_it821x
[ 23.837057] ata5: PATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xa400 irq 20
[ 23.844241] ata6: PATA max UDMA/133 cmd 0xb000 ctl 0xa800 bmdma 0xa408 irq 20
[ 24.014173] async_waiting @ 1
[ 24.017193] async_continuing @ 1 after 0 usec
[ 24.021597] async_waiting @ 1
[ 24.024620] async_continuing @ 1 after 0 usec
[ 24.194169] async_waiting @ 1
[ 24.197192] async_continuing @ 1 after 0 usec
[ 24.201691] initcall it821x_init+0x0/0x1b returned 0 after 398112 usecs
[ 24.208355] calling ninja32_init+0x0/0x1b @ 1
[ 24.212947] initcall ninja32_init+0x0/0x1b returned 0 after 90 usecs
[ 24.219353] calling ns87415_init+0x0/0x1b @ 1
[ 24.223955] initcall ns87415_init+0x0/0x1b returned 0 after 91 usecs
[ 24.230359] calling opti_init+0x0/0x1b @ 1
[ 24.234697] initcall opti_init+0x0/0x1b returned 0 after 86 usecs
[ 24.240838] calling mpiix_init+0x0/0x1b @ 1
[ 24.245274] initcall mpiix_init+0x0/0x1b returned 0 after 97 usecs
[ 24.251506] calling oldpiix_init+0x0/0x1b @ 1
[ 24.256110] initcall oldpiix_init+0x0/0x1b returned 0 after 87 usecs
[ 24.262513] calling rz1000_init+0x0/0x1b @ 1
[ 24.267027] initcall rz1000_init+0x0/0x1b returned 0 after 87 usecs
[ 24.273346] calling sc1200_init+0x0/0x1b @ 1
[ 24.277861] initcall sc1200_init+0x0/0x1b returned 0 after 87 usecs
[ 24.284180] calling via_init+0x0/0x1b @ 1
[ 24.288436] initcall via_init+0x0/0x1b returned 0 after 90 usecs
[ 24.294492] calling sis_init+0x0/0x1b @ 1
[ 24.298747] initcall sis_init+0x0/0x1b returned 0 after 87 usecs
[ 24.304806] calling triflex_init+0x0/0x1f @ 1
[ 24.309407] initcall triflex_init+0x0/0x1f returned 0 after 87 usecs
[ 24.315813] calling fw_core_init+0x0/0xbe @ 1
[ 24.320423] initcall fw_core_init+0x0/0xbe returned 0 after 97 usecs
[ 24.326827] calling cdrom_init+0x0/0x77 @ 1
[ 24.331167] initcall cdrom_init+0x0/0x77 returned 0 after 9 usecs
[ 24.337315] calling gpio_vbus_init+0x0/0x19 @ 1
[ 24.342156] initcall gpio_vbus_init+0x0/0x19 returned -19 after 165 usecs
[ 24.348998] calling mon_init+0x0/0x105 @ 1
[ 24.353510] initcall mon_init+0x0/0x105 returned 0 after 255 usecs
[ 24.359744] calling ehci_hcd_init+0x0/0xe9 @ 1
[ 24.364350] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 24.370923] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[ 24.377012] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 24.384216] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 24.390104] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 24.395512] drivers/usb/core/inode.c: creating file 'devices'
[ 24.401318] drivers/usb/core/inode.c: creating file '001'
[ 24.406926] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 24.414396] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
[ 24.423780] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[ 24.432136] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 24.444950] ehci_hcd 0000:00:1d.7: debug port 1
[ 24.449533] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 24.456453] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 24.462251] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xd7cff800
[ 24.467966] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 24.480771] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 24.500010] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 24.505849] usb usb1: default language 0x0409
[ 24.510277] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 24.517113] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 24.524400] usb usb1: Product: EHCI Host Controller
[ 24.529323] usb usb1: Manufacturer: Linux 2.6.29-rc3-00697-gae1a25d ehci_hcd
[ 24.536421] usb usb1: SerialNumber: 0000:00:1d.7
[ 24.541194] usb usb1: uevent
[ 24.544207] usb usb1: usb_probe_device
[ 24.548010] usb usb1: configuration #1 chosen from 1 choice
[ 24.553652] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 24.559486] usb 1-0:1.0: uevent
[ 24.562763] hub 1-0:1.0: usb_probe_interface
[ 24.567084] hub 1-0:1.0: usb_probe_interface - got id
[ 24.572191] hub 1-0:1.0: USB hub found
[ 24.576007] hub 1-0:1.0: 8 ports detected
[ 24.580067] hub 1-0:1.0: standalone hub
[ 24.583941] hub 1-0:1.0: no power switching (usb 1.0)
[ 24.589045] hub 1-0:1.0: individual port over-current protection
[ 24.595094] hub 1-0:1.0: power on to power good time: 20ms
[ 24.600644] hub 1-0:1.0: local power source is good
[ 24.605574] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 24.612772] drivers/usb/core/inode.c: creating file '001'
[ 24.618461] initcall ehci_hcd_init+0x0/0xe9 returned 0 after 248152 usecs
[ 24.625312] calling oxu_module_init+0x0/0x12 @ 1
[ 24.630158] initcall oxu_module_init+0x0/0x12 returned 0 after 89 usecs
[ 24.636826] calling ohci_hcd_mod_init+0x0/0xb8 @ 1
[ 24.641777] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 24.648006] ohci_hcd: block sizes: ed 80 td 96
[ 24.652603] initcall ohci_hcd_mod_init+0x0/0xb8 returned 0 after 10570 usecs
[ 24.659698] calling uhci_hcd_init+0x0/0x10a @ 1
[ 24.664398] uhci_hcd: USB Universal Host Controller Interface driver
[ 24.671004] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 24.678199] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 24.684100] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 24.689481] drivers/usb/core/inode.c: creating file '002'
[ 24.695068] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 24.702552] uhci_hcd 0000:00:1d.0: detected 2 ports
[ 24.707486] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 24.714237] uhci_hcd 0000:00:1d.0: Performing full reset
[ 24.719612] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 24.725413] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00007000
[ 24.731260] usb usb2: default language 0x0409
[ 24.735687] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 24.742524] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 24.749812] usb usb2: Product: UHCI Host Controller
[ 24.754734] usb usb2: Manufacturer: Linux 2.6.29-rc3-00697-gae1a25d uhci_hcd
[ 24.761832] usb usb2: SerialNumber: 0000:00:1d.0
[ 24.766572] usb usb2: uevent
[ 24.769607] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
[ 24.775163] usb usb2: usb_probe_device
[ 24.778981] usb usb2: configuration #1 chosen from 1 choice
[ 24.784611] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 24.790436] usb 2-0:1.0: uevent
[ 24.793713] hub 2-0:1.0: usb_probe_interface
[ 24.798034] hub 2-0:1.0: usb_probe_interface - got id
[ 24.803162] hub 2-0:1.0: USB hub found
[ 24.806971] hub 2-0:1.0: 2 ports detected
[ 24.811034] hub 2-0:1.0: standalone hub
[ 24.814915] hub 2-0:1.0: no power switching (usb 1.0)
[ 24.820012] hub 2-0:1.0: individual port over-current protection
[ 24.826071] hub 2-0:1.0: power on to power good time: 2ms
[ 24.831528] hub 2-0:1.0: local power source is good
[ 24.836454] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 24.843518] drivers/usb/core/inode.c: creating file '001'
[ 24.849145] alloc irq_desc for 17 on cpu 0 node 0
[ 24.852966] alloc kstat_irqs on cpu 0 node 0
[ 24.858578] IOAPIC[0]: Set routing entry (2-17 -> 0x71 -> IRQ 17 Mode:1 Active:1)
[ 24.866129] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 24.873318] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 24.879197] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 24.884583] drivers/usb/core/inode.c: creating file '003'
[ 24.890162] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 24.897646] uhci_hcd 0000:00:1d.1: detected 2 ports
[ 24.902574] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 24.909322] uhci_hcd 0000:00:1d.1: Performing full reset
[ 24.914689] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[ 24.920502] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00007400
[ 24.926357] usb usb3: default language 0x0409
[ 24.930786] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 24.937620] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 24.944907] usb usb3: Product: UHCI Host Controller
[ 24.949830] usb usb3: Manufacturer: Linux 2.6.29-rc3-00697-gae1a25d uhci_hcd
[ 24.956934] usb usb3: SerialNumber: 0000:00:1d.1
[ 24.961673] usb usb3: uevent
[ 24.964712] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 24.970264] usb usb3: usb_probe_device
[ 24.974086] usb usb3: configuration #1 chosen from 1 choice
[ 24.979715] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 24.985545] usb 3-0:1.0: uevent
[ 24.988814] hub 3-0:1.0: usb_probe_interface
[ 24.993137] hub 3-0:1.0: usb_probe_interface - got id
[ 24.998256] hub 3-0:1.0: USB hub found
[ 25.002066] hub 3-0:1.0: 2 ports detected
[ 25.006129] hub 3-0:1.0: standalone hub
[ 25.010010] hub 3-0:1.0: no power switching (usb 1.0)
[ 25.015107] hub 3-0:1.0: individual port over-current protection
[ 25.021157] hub 3-0:1.0: power on to power good time: 2ms
[ 25.026616] hub 3-0:1.0: local power source is good
[ 25.031540] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 25.038608] drivers/usb/core/inode.c: creating file '001'
[ 25.044216] alloc irq_desc for 18 on cpu 0 node 0
[ 25.048052] alloc kstat_irqs on cpu 0 node 0
[ 25.053649] IOAPIC[0]: Set routing entry (2-18 -> 0x79 -> IRQ 18 Mode:1 Active:1)
[ 25.061199] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 25.068387] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 25.074267] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 25.079649] drivers/usb/core/inode.c: creating file '004'
[ 25.085231] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 25.092714] uhci_hcd 0000:00:1d.2: detected 2 ports
[ 25.097642] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 25.104391] uhci_hcd 0000:00:1d.2: Performing full reset
[ 25.109757] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[ 25.115569] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00007800
[ 25.121420] usb usb4: default language 0x0409
[ 25.125842] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 25.132680] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.139968] usb usb4: Product: UHCI Host Controller
[ 25.144891] usb usb4: Manufacturer: Linux 2.6.29-rc3-00697-gae1a25d uhci_hcd
[ 25.151988] usb usb4: SerialNumber: 0000:00:1d.2
[ 25.156732] usb usb4: uevent
[ 25.159745] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 25.165300] usb usb4: usb_probe_device
[ 25.169121] usb usb4: configuration #1 chosen from 1 choice
[ 25.174750] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 25.180576] usb 4-0:1.0: uevent
[ 25.183840] hub 4-0:1.0: usb_probe_interface
[ 25.188163] hub 4-0:1.0: usb_probe_interface - got id
[ 25.193282] hub 4-0:1.0: USB hub found
[ 25.197092] hub 4-0:1.0: 2 ports detected
[ 25.201168] hub 4-0:1.0: standalone hub
[ 25.205054] hub 4-0:1.0: no power switching (usb 1.0)
[ 25.210149] hub 4-0:1.0: individual port over-current protection
[ 25.216200] hub 4-0:1.0: power on to power good time: 2ms
[ 25.221661] hub 4-0:1.0: local power source is good
[ 25.226592] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 25.233665] drivers/usb/core/inode.c: creating file '001'
[ 25.239273] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 25.246479] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 25.252360] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 25.257745] drivers/usb/core/inode.c: creating file '005'
[ 25.263327] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 25.270813] uhci_hcd 0000:00:1d.3: detected 2 ports
[ 25.275742] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[ 25.282491] uhci_hcd 0000:00:1d.3: Performing full reset
[ 25.287858] uhci_hcd 0000:00:1d.3: supports USB remote wakeup
[ 25.293661] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00008000
[ 25.299506] usb usb5: default language 0x0409
[ 25.303935] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 25.310771] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 25.318059] usb usb5: Product: UHCI Host Controller
[ 25.322981] usb usb5: Manufacturer: Linux 2.6.29-rc3-00697-gae1a25d uhci_hcd
[ 25.330079] usb usb5: SerialNumber: 0000:00:1d.3
[ 25.334816] usb usb5: uevent
[ 25.337833] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 25.343382] usb usb5: usb_probe_device
[ 25.347550] usb usb5: configuration #1 chosen from 1 choice
[ 25.353177] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 25.359008] usb 5-0:1.0: uevent
[ 25.362278] hub 5-0:1.0: usb_probe_interface
[ 25.366601] hub 5-0:1.0: usb_probe_interface - got id
[ 25.371722] hub 5-0:1.0: USB hub found
[ 25.375529] hub 5-0:1.0: 2 ports detected
[ 25.379593] hub 5-0:1.0: standalone hub
[ 25.383474] hub 5-0:1.0: no power switching (usb 1.0)
[ 25.388570] hub 5-0:1.0: individual port over-current protection
[ 25.394621] hub 5-0:1.0: power on to power good time: 2ms
[ 25.400078] hub 5-0:1.0: local power source is good
[ 25.405005] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 25.412075] drivers/usb/core/inode.c: creating file '001'
[ 25.417794] initcall uhci_hcd_init+0x0/0x10a returned 0 after 735734 usecs
[ 25.424739] calling sl811h_init+0x0/0x42 @ 1
[ 25.429149] sl811: driver sl811-hcd, 19 May 2005
[ 25.433906] initcall sl811h_init+0x0/0x42 returned 0 after 4644 usecs
[ 25.440399] calling acm_init+0x0/0x13f @ 1
[ 25.444749] usbcore: registered new interface driver cdc_acm
[ 25.450488] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 25.459110] initcall acm_init+0x0/0x13f returned 0 after 14118 usecs
[ 25.465516] calling usb_stor_init+0x0/0x55 @ 1
[ 25.470099] Initializing USB Mass Storage driver...
[ 25.475135] usbcore: registered new interface driver usb-storage
[ 25.481194] USB Mass Storage support registered.
[ 25.485880] initcall usb_stor_init+0x0/0x55 returned 0 after 15409 usecs
[ 25.492634] calling usb_usual_init+0x0/0x41 @ 1
[ 25.497406] usbcore: registered new interface driver libusual
[ 25.503212] initcall usb_usual_init+0x0/0x41 returned 0 after 5769 usecs
[ 25.509984] calling usb_mdc800_init+0x0/0x26f @ 1
[ 25.514932] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 25.520480] usbcore: registered new interface driver mdc800
[ 25.526117] mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
[ 25.533844] initcall usb_mdc800_init+0x0/0x26f returned 0 after 18568 usecs
[ 25.540854] calling adu_init+0x0/0x9d @ 1
[ 25.544997] drivers/usb/misc/adutux.c : adu_init : enter
[ 25.550625] usbcore: registered new interface driver adutux
[ 25.556247] adutux adutux (see www.ontrak.net) v0.0.13
[ 25.561450] adutux is an experimental driver. Use at your own risk
[ 25.567677] drivers/usb/misc/adutux.c : adu_init : leave, return value 0
[ 25.574604] initcall adu_init+0x0/0x9d returned 0 after 28912 usecs
[ 25.580920] calling emi62_init+0x0/0x3d @ 1
[ 25.585321] usbcore: registered new interface driver emi62 - firmware loader
[ 25.592425] initcall emi62_init+0x0/0x3d returned 0 after 7018 usecs
[ 25.598840] calling usb_idmouse_init+0x0/0x4d @ 1
[ 25.603678] idmouse: 0.6:Siemens ID Mouse FingerTIP Sensor Driver
[ 25.609897] usbcore: registered new interface driver idmouse
[ 25.615608] initcall usb_idmouse_init+0x0/0x4d returned 0 after 11648 usecs
[ 25.622629] calling ld_usb_init+0x0/0x3f @ 1
[ 25.627131] usbcore: registered new interface driver ldusb
[ 25.632672] initcall ld_usb_init+0x0/0x3f returned 0 after 5502 usecs
[ 25.639174] calling usbtest_init+0x0/0x41 @ 1
[ 25.643757] usbcore: registered new interface driver usbtest
[ 25.649468] initcall usbtest_init+0x0/0x41 returned 0 after 5664 usecs
[ 25.656057] calling tv_init+0x0/0x4d @ 1
[ 25.660199] usbcore: registered new interface driver trancevibrator
[ 25.666513] trancevibrator: v1.1:PlayStation 2 Trance Vibrator driver
[ 25.673018] initcall tv_init+0x0/0x4d returned 0 after 12598 usecs
[ 25.679244] calling uss720_init+0x0/0x67 @ 1
[ 25.683745] usbcore: registered new interface driver uss720
[ 25.689367] uss720: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip
[ 25.698772] uss720: NOTE: this is a special purpose driver to allow nonstandard
[ 25.706143] uss720: protocols (eg. bitbang) over USS720 usb to parallel cables
[ 25.713432] uss720: If you just want to connect to a printer, use usblp instead
[ 25.720810] initcall uss720_init+0x0/0x67 returned 0 after 36283 usecs
[ 25.727387] calling usb_sevseg_init+0x0/0x3f @ 1
[ 25.732237] usbcore: registered new interface driver usbsevseg
[ 25.738119] initcall usb_sevseg_init+0x0/0x3f returned 0 after 5833 usecs
[ 25.744967] calling vstusb_init+0x0/0x46 @ 1
[ 25.749458] usbcore: registered new interface driver vstusb
[ 25.755081] initcall vstusb_init+0x0/0x46 returned 0 after 5571 usecs
[ 25.761582] calling usb_sisusb_init+0x0/0x1e @ 1
[ 25.766418] usbcore: registered new interface driver sisusb
[ 25.772041] initcall usb_sisusb_init+0x0/0x1e returned 0 after 5571 usecs
[ 25.778890] calling i8042_init+0x0/0x413 @ 1
[ 25.783652] PNP: No PS/2 controller found. Probing ports directly.
[ 25.792234] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 25.797252] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 25.802358] initcall i8042_init+0x0/0x413 returned 0 after 18613 usecs
[ 25.808932] calling serio_raw_init+0x0/0x1d @ 1
[ 25.813823] initcall serio_raw_init+0x0/0x1d returned 0 after 213 usecs
[ 25.820486] calling l4_init+0x0/0x3e0 @ 1
[ 25.824684] initcall l4_init+0x0/0x3e0 returned -19 after 8 usecs
[ 25.830823] calling ns558_init+0x0/0x360 @ 1
[ 25.848215] initcall ns558_init+0x0/0x360 returned 0 after 12674 usecs
[ 25.854795] calling mousedev_init+0x0/0x92 @ 1
[ 25.859647] mice: PS/2 mouse device common for all mice
[ 25.864929] initcall mousedev_init+0x0/0x92 returned 0 after 5417 usecs
[ 25.871618] calling atkbd_init+0x0/0x27 @ 1
[ 25.876040] initcall atkbd_init+0x0/0x27 returned 0 after 94 usecs
[ 25.882298] calling lkkbd_init+0x0/0x1b @ 1
[ 25.886733] initcall lkkbd_init+0x0/0x1b returned 0 after 108 usecs
[ 25.893051] calling xtkbd_init+0x0/0x1d @ 1
[ 25.897482] initcall xtkbd_init+0x0/0x1d returned 0 after 89 usecs
[ 25.903710] calling atp_init+0x0/0x1b @ 1
[ 25.908127] usbcore: registered new interface driver appletouch
[ 25.914109] initcall atp_init+0x0/0x1b returned 0 after 6083 usecs
[ 25.920347] calling sermouse_init+0x0/0x25 @ 1
[ 25.925074] initcall sermouse_init+0x0/0x25 returned 0 after 142 usecs
[ 25.931652] calling gpio_mouse_init+0x0/0x19 @ 1
[ 25.936616] initcall gpio_mouse_init+0x0/0x19 returned -19 after 180 usecs
[ 25.943543] calling gf2k_init+0x0/0x1b @ 1
[ 25.947787] usb usb2: suspend_rh (auto-stop)
[ 25.952239] initcall gf2k_init+0x0/0x1b returned 0 after 86 usecs
[ 25.958381] calling grip_init+0x0/0x1b @ 1
[ 25.962731] initcall grip_init+0x0/0x1b returned 0 after 87 usecs
[ 25.968877] calling guillemot_init+0x0/0x1b @ 1
[ 25.973650] initcall guillemot_init+0x0/0x1b returned 0 after 86 usecs
[ 25.980229] calling magellan_init+0x0/0x1b @ 1
[ 25.984923] initcall magellan_init+0x0/0x1b returned 0 after 91 usecs
[ 25.991417] calling spaceorb_init+0x0/0x1b @ 1
[ 25.996118] initcall spaceorb_init+0x0/0x1b returned 0 after 95 usecs
[ 26.002608] calling twidjoy_init+0x0/0x1b @ 1
[ 26.007209] initcall twidjoy_init+0x0/0x1b returned 0 after 87 usecs
[ 26.013614] calling ati_remote_init+0x0/0x4d @ 1
[ 26.018479] usbcore: registered new interface driver ati_remote
[ 26.024448] ati_remote: 2.2.1:ATI/X10 RF USB Remote Control
[ 26.030085] initcall ati_remote_init+0x0/0x4d returned 0 after 11425 usecs
[ 26.037014] calling ati_remote2_init+0x0/0x4d @ 1
[ 26.041957] usbcore: registered new interface driver ati_remote2
[ 26.048012] ati_remote2: ATI/Philips USB RF remote driver 0.3
[ 26.053824] initcall ati_remote2_init+0x0/0x4d returned 0 after 11684 usecs
[ 26.060838] calling usb_keyspan_init+0x0/0x3f @ 1
[ 26.065780] usbcore: registered new interface driver keyspan_remote
[ 26.072099] initcall usb_keyspan_init+0x0/0x3f returned 0 after 6266 usecs
[ 26.079035] calling yealink_dev_init+0x0/0x3d @ 1
[ 26.083957] usbcore: registered new interface driver yealink
[ 26.089663] yealink: yld-20051230:Yealink phone driver
[ 26.094868] initcall yealink_dev_init+0x0/0x3d returned 0 after 10735 usecs
[ 26.101883] calling pcf50633_input_init+0x0/0x1f @ 1
[ 26.107072] initcall pcf50633_input_init+0x0/0x1f returned 0 after 81 usecs
[ 26.114086] calling i2o_iop_init+0x0/0x62 @ 1
[ 26.118596] I2O subsystem v1.325
[ 26.121875] i2o: max drivers = 8
[ 26.125476] initcall i2o_iop_init+0x0/0x62 returned 0 after 6716 usecs
[ 26.132052] calling i2o_bus_init+0x0/0x49 @ 1
[ 26.136561] I2O Bus Adapter OSM v1.317
[ 26.140445] initcall i2o_bus_init+0x0/0x49 returned 0 after 3790 usecs
[ 26.147019] calling i2o_block_init+0x0/0x128 @ 1
[ 26.151806] I2O Block Device OSM v1.325
[ 26.156322] initcall i2o_block_init+0x0/0x128 returned 0 after 4407 usecs
[ 26.163170] calling ds1742_init+0x0/0x12 @ 1
[ 26.167660] initcall ds1742_init+0x0/0x12 returned 0 after 81 usecs
[ 26.173982] calling fm3130_init+0x0/0x14 @ 1
[ 26.178494] i2c-core: driver [rtc-fm3130] registered
[ 26.183517] initcall fm3130_init+0x0/0x14 returned 0 after 4988 usecs
[ 26.190029] calling isl1208_init+0x0/0x14 @ 1
[ 26.194525] usb usb3: suspend_rh (auto-stop)
[ 26.198956] i2c-core: driver [rtc-isl1208] registered
[ 26.204057] initcall isl1208_init+0x0/0x14 returned 0 after 5064 usecs
[ 26.210647] calling m41t80_rtc_init+0x0/0x14 @ 1
[ 26.215479] i2c-core: driver [rtc-m41t80] registered
[ 26.220497] initcall m41t80_rtc_init+0x0/0x14 returned 0 after 4978 usecs
[ 26.227348] calling m48t59_rtc_init+0x0/0x12 @ 1
[ 26.232184] initcall m48t59_rtc_init+0x0/0x12 returned 0 after 81 usecs
[ 26.238852] calling m48t86_rtc_init+0x0/0x12 @ 1
[ 26.243711] initcall m48t86_rtc_init+0x0/0x12 returned 0 after 86 usecs
[ 26.250379] calling bq4802_init+0x0/0x12 @ 1
[ 26.254910] initcall bq4802_init+0x0/0x12 returned 0 after 104 usecs
[ 26.261316] calling max6900_init+0x0/0x14 @ 1
[ 26.265918] i2c-core: driver [rtc-max6900] registered
[ 26.271022] initcall max6900_init+0x0/0x14 returned 0 after 5075 usecs
[ 26.277613] calling rx8581_init+0x0/0x14 @ 1
[ 26.282109] i2c-core: driver [rtc-rx8581] registered
[ 26.287126] initcall rx8581_init+0x0/0x14 returned 0 after 4985 usecs
[ 26.293629] calling s35390a_rtc_init+0x0/0x14 @ 1
[ 26.298559] i2c-core: driver [rtc-s35390a] registered
[ 26.303661] initcall s35390a_rtc_init+0x0/0x14 returned 0 after 5069 usecs
[ 26.310598] calling v3020_init+0x0/0x12 @ 1
[ 26.315002] initcall v3020_init+0x0/0x12 returned 0 after 80 usecs
[ 26.321237] calling pcf50633_rtc_init+0x0/0x12 @ 1
[ 26.326264] initcall pcf50633_rtc_init+0x0/0x12 returned 0 after 80 usecs
[ 26.333101] calling i2c_dev_init+0x0/0xac @ 1
[ 26.337956] i2c /dev entries driver
[ 26.341670] i2c-core: driver [dev_driver] registered
[ 26.346847] i2c-dev: adapter [via_i2c] registered as minor 0
[ 26.352573] initcall i2c_dev_init+0x0/0xac returned 0 after 14271 usecs
[ 26.359239] calling i2c_amd8111_init+0x0/0x1b @ 1
[ 26.364190] initcall i2c_amd8111_init+0x0/0x1b returned 0 after 102 usecs
[ 26.371027] calling i2c_sch_init+0x0/0x1b @ 1
[ 26.375637] initcall i2c_sch_init+0x0/0x1b returned 0 after 88 usecs
[ 26.382042] calling i2c_piix4_init+0x0/0x1b @ 1
[ 26.386827] initcall i2c_piix4_init+0x0/0x1b returned 0 after 89 usecs
[ 26.393404] calling i2c_sis96x_init+0x0/0x1b @ 1
[ 26.398268] initcall i2c_sis96x_init+0x0/0x1b returned 0 after 87 usecs
[ 26.404930] calling i2c_vt586b_init+0x0/0x1b @ 1
[ 26.409791] initcall i2c_vt586b_init+0x0/0x1b returned 0 after 87 usecs
[ 26.416457] calling ocores_i2c_init+0x0/0x12 @ 1
[ 26.421317] initcall ocores_i2c_init+0x0/0x12 returned 0 after 85 usecs
[ 26.427983] calling usb_i2c_tiny_usb_init+0x0/0x1b @ 1
[ 26.433363] usbcore: registered new interface driver i2c-tiny-usb
[ 26.439513] initcall usb_i2c_tiny_usb_init+0x0/0x1b returned 0 after 6092 usecs
[ 26.446890] usb usb4: suspend_rh (auto-stop)
[ 26.451225] usb usb5: suspend_rh (auto-stop)
[ 26.455568] calling i2c_voodoo3_init+0x0/0x1b @ 1
[ 26.460504] initcall i2c_voodoo3_init+0x0/0x1b returned 0 after 86 usecs
[ 26.467252] calling ds1682_init+0x0/0x14 @ 1
[ 26.471757] i2c-core: driver [ds1682] registered
[ 26.476423] initcall ds1682_init+0x0/0x14 returned 0 after 4635 usecs
[ 26.482925] calling max6875_init+0x0/0x14 @ 1
[ 26.487504] i2c-core: driver [max6875] registered
[ 26.492263] initcall max6875_init+0x0/0x14 returned 0 after 4729 usecs
[ 26.498855] calling pcf8574_init+0x0/0x14 @ 1
[ 26.503428] i2c-core: driver [pcf8574] registered
[ 26.508191] initcall pcf8574_init+0x0/0x14 returned 0 after 4729 usecs
[ 26.514784] calling pcf8591_init+0x0/0x46 @ 1
[ 26.519362] i2c-core: driver [pcf8591] registered
[ 26.524121] initcall pcf8591_init+0x0/0x46 returned 0 after 4729 usecs
[ 26.530713] calling sensors_w83792d_init+0x0/0x14 @ 1
[ 26.535981] i2c-core: driver [w83792d] registered
[ 26.540743] initcall sensors_w83792d_init+0x0/0x14 returned 0 after 4727 usecs
[ 26.548046] calling sensors_w83781d_init+0x0/0x18 @ 1
[ 26.553315] i2c-core: driver [w83781d] registered
[ 26.558077] initcall sensors_w83781d_init+0x0/0x18 returned 0 after 4728 usecs
[ 26.565380] calling abituguru_init+0x0/0x1b2 @ 1
[ 26.570136] initcall abituguru_init+0x0/0x1b2 returned -19 after 0 usecs
[ 26.576885] calling ad7418_init+0x0/0x14 @ 1
[ 26.581369] i2c-core: driver [ad7418] registered
[ 26.586039] initcall ad7418_init+0x0/0x14 returned 0 after 4639 usecs
[ 26.592543] calling sensors_adm1025_init+0x0/0x14 @ 1
[ 26.597809] i2c-core: driver [adm1025] registered
[ 26.602571] initcall sensors_adm1025_init+0x0/0x14 returned 0 after 4728 usecs
[ 26.609876] calling sensors_adm1029_init+0x0/0x14 @ 1
[ 26.615142] i2c-core: driver [adm1029] registered
[ 26.619904] initcall sensors_adm1029_init+0x0/0x14 returned 0 after 4728 usecs
[ 26.627209] calling sensors_adm1031_init+0x0/0x14 @ 1
[ 26.632480] i2c-core: driver [adm1031] registered
[ 26.637238] initcall sensors_adm1031_init+0x0/0x14 returned 0 after 4729 usecs
[ 26.644541] calling sensors_adm9240_init+0x0/0x1e @ 1
[ 26.649809] i2c-core: driver [adm9240] registered
[ 26.654572] initcall sensors_adm9240_init+0x0/0x1e returned 0 after 4728 usecs
[ 26.661875] calling applesmc_init+0x0/0x600 @ 1
[ 26.666547] applesmc: supported laptop not found!
[ 26.671299] applesmc: driver init failed (ret=-19)!
[ 26.676223] initcall applesmc_init+0x0/0x600 returned -19 after 9452 usecs
[ 26.683146] calling coretemp_init+0x0/0x210 @ 1
[ 26.687989] initcall coretemp_init+0x0/0x210 returned -19 after 165 usecs
[ 26.694831] calling dme1737_init+0x0/0x19f @ 1
[ 26.699508] i2c-core: driver [dme1737] registered
[ 26.704276] initcall dme1737_init+0x0/0x19f returned 0 after 4735 usecs
[ 26.710963] calling f71805f_init+0x0/0x171 @ 1
[ 26.715559] initcall f71805f_init+0x0/0x171 returned -19 after 15 usecs
[ 26.722225] calling sensors_fscher_init+0x0/0x14 @ 1
[ 26.727413] i2c-core: driver [fscher] registered
[ 26.732086] initcall sensors_fscher_init+0x0/0x14 returned 0 after 4643 usecs
[ 26.739286] calling fschmd_init+0x0/0x14 @ 1
[ 26.743774] i2c-core: driver [fschmd] registered
[ 26.748449] initcall fschmd_init+0x0/0x14 returned 0 after 4643 usecs
[ 26.754957] calling sm_fscpos_init+0x0/0x14 @ 1
[ 26.759703] i2c-core: driver [fscpos] registered
[ 26.764378] initcall sm_fscpos_init+0x0/0x14 returned 0 after 4644 usecs
[ 26.771144] calling sensors_gl520sm_init+0x0/0x14 @ 1
[ 26.776412] i2c-core: driver [gl520sm] registered
[ 26.781173] initcall sensors_gl520sm_init+0x0/0x14 returned 0 after 4727 usecs
[ 26.788479] calling i5k_amb_init+0x0/0x6b @ 1
[ 26.793197] initcall i5k_amb_init+0x0/0x6b returned 0 after 220 usecs
[ 26.799689] calling lis3lv02d_init_module+0x0/0x37 @ 1
[ 26.805088] lis3lv02d driver loaded.
[ 26.808720] initcall lis3lv02d_init_module+0x0/0x37 returned 0 after 3653 usecs
[ 26.816119] calling sensors_lm63_init+0x0/0x1f @ 1
[ 26.821130] hub 1-0:1.0: hub_suspend
[ 26.824766] usb usb1: bus auto-suspend
[ 26.828578] ehci_hcd 0000:00:1d.7: suspend root hub
[ 26.833532] i2c-core: driver [lm63] registered
[ 26.838036] initcall sensors_lm63_init+0x0/0x1f returned 0 after 16584 usecs
[ 26.845152] calling sm_lm78_init+0x0/0x403 @ 1
[ 26.849846] i2c-core: driver [lm78] registered
[ 26.854347] initcall sm_lm78_init+0x0/0x403 returned 0 after 4509 usecs
[ 26.861017] calling sensors_lm83_init+0x0/0x14 @ 1
[ 26.866026] i2c-core: driver [lm83] registered
[ 26.870528] initcall sensors_lm83_init+0x0/0x14 returned 0 after 4475 usecs
[ 26.877555] calling sensors_lm87_init+0x0/0x14 @ 1
[ 26.882564] i2c-core: driver [lm87] registered
[ 26.887063] initcall sensors_lm87_init+0x0/0x14 returned 0 after 4474 usecs
[ 26.894087] calling sensors_lm90_init+0x0/0x14 @ 1
[ 26.899098] i2c-core: driver [lm90] registered
[ 26.903600] initcall sensors_lm90_init+0x0/0x14 returned 0 after 4474 usecs
[ 26.910626] calling sensors_max1619_init+0x0/0x14 @ 1
[ 26.915894] i2c-core: driver [max1619] registered
[ 26.920656] initcall sensors_max1619_init+0x0/0x14 returned 0 after 4728 usecs
[ 26.927958] calling pc87360_init+0x0/0x1bf @ 1
[ 26.932549] pc87360: PC8736x not detected, module not inserted.
[ 26.938520] initcall pc87360_init+0x0/0x1bf returned -19 after 5838 usecs
[ 26.945357] calling sm_sis5595_init+0x0/0x1b @ 1
[ 26.950207] initcall sm_sis5595_init+0x0/0x1b returned 0 after 97 usecs
[ 26.956868] calling sm_thmc50_init+0x0/0x14 @ 1
[ 26.961632] i2c-core: driver [thmc50] registered
[ 26.966311] initcall sm_thmc50_init+0x0/0x14 returned 0 after 4647 usecs
[ 26.973077] calling sm_via686a_init+0x0/0x1b @ 1
[ 26.977923] initcall sm_via686a_init+0x0/0x1b returned 0 after 89 usecs
[ 26.984592] calling sm_vt8231_init+0x0/0x1b @ 1
[ 26.989376] initcall sm_vt8231_init+0x0/0x1b returned 0 after 97 usecs
[ 26.995954] calling cpufreq_gov_userspace_init+0x0/0x12 @ 1
[ 27.001681] initcall cpufreq_gov_userspace_init+0x0/0x12 returned 0 after 1 usecs
[ 27.009230] calling cpufreq_gov_dbs_init+0x0/0x12 @ 1
[ 27.014423] initcall cpufreq_gov_dbs_init+0x0/0x12 returned 0 after 0 usecs
[ 27.021433] calling init_ladder+0x0/0x12 @ 1
[ 27.025837] cpuidle: using governor ladder
[ 27.029987] initcall init_ladder+0x0/0x12 returned 0 after 4053 usecs
[ 27.036478] calling init_menu+0x0/0x12 @ 1
[ 27.040716] cpuidle: using governor menu
[ 27.044686] initcall init_menu+0x0/0x12 returned 0 after 3876 usecs
[ 27.051003] calling alix_led_init+0x0/0x108 @ 1
[ 27.057342] initcall alix_led_init+0x0/0x108 returned -19 after 1636 usecs
[ 27.064264] calling pca955x_leds_init+0x0/0x14 @ 1
[ 27.069278] i2c-core: driver [leds-pca955x] registered
[ 27.074467] initcall pca955x_leds_init+0x0/0x14 returned 0 after 5147 usecs
[ 27.081490] calling dcdrbu_init+0x0/0x13e @ 1
[ 27.086088] initcall dcdrbu_init+0x0/0x13e returned 0 after 101 usecs
[ 27.092578] calling compal_init+0x0/0x120 @ 1
[ 27.097092] initcall compal_init+0x0/0x120 returned -19 after 2 usecs
[ 27.103584] calling acer_wmi_init+0x0/0x6ca @ 1
[ 27.108255] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 27.113013] acer-wmi: No or unsupported WMI interface, unable to load
[ 27.119506] initcall acer_wmi_init+0x0/0x6ca returned -19 after 10986 usecs
[ 27.126517] calling sony_laptop_init+0x0/0x86 @ 1
[ 27.131443] initcall sony_laptop_init+0x0/0x86 returned 0 after 87 usecs
[ 27.138192] calling thinkpad_acpi_module_init+0x0/0xa4b @ 1
[ 27.143961] initcall thinkpad_acpi_module_init+0x0/0xa4b returned -19 after 44 usecs
[ 27.151772] calling init_soundcore+0x0/0x80 @ 1
[ 27.156531] initcall init_soundcore+0x0/0x80 returned 0 after 85 usecs
[ 27.163108] calling alsa_sound_init+0x0/0x8d @ 1
[ 27.167929] Advanced Linux Sound Architecture Driver Version 1.0.18a.
[ 27.174418] initcall alsa_sound_init+0x0/0x8d returned 0 after 6385 usecs
[ 27.181255] calling alsa_hwdep_init+0x0/0x70 @ 1
[ 27.186023] initcall alsa_hwdep_init+0x0/0x70 returned 0 after 8 usecs
[ 27.192600] calling alsa_timer_init+0x0/0x212 @ 1
[ 27.197628] initcall alsa_timer_init+0x0/0x212 returned 0 after 178 usecs
[ 27.204464] calling snd_hrtimer_init+0x0/0x196 @ 1
[ 27.209413] initcall snd_hrtimer_init+0x0/0x196 returned 0 after 3 usecs
[ 27.216165] calling alsa_pcm_init+0x0/0x71 @ 1
[ 27.220758] initcall alsa_pcm_init+0x0/0x71 returned 0 after 7 usecs
[ 27.227163] calling snd_mem_init+0x0/0x2c @ 1
[ 27.231668] initcall snd_mem_init+0x0/0x2c returned 0 after 6 usecs
[ 27.237988] calling alsa_rawmidi_init+0x0/0x89 @ 1
[ 27.242922] initcall alsa_rawmidi_init+0x0/0x89 returned 0 after 2 usecs
[ 27.249669] calling alsa_opl3_init+0x0/0x8 @ 1
[ 27.254246] initcall alsa_opl3_init+0x0/0x8 returned 0 after 0 usecs
[ 27.260650] calling alsa_mpu401_uart_init+0x0/0x8 @ 1
[ 27.265842] initcall alsa_mpu401_uart_init+0x0/0x8 returned 0 after 0 usecs
[ 27.272852] calling alsa_sb_common_init+0x0/0x8 @ 1
[ 27.278210] initcall alsa_sb_common_init+0x0/0x8 returned 0 after 0 usecs
[ 27.285046] calling alsa_card_als300_init+0x0/0x1b @ 1
[ 27.290422] initcall alsa_card_als300_init+0x0/0x1b returned 0 after 94 usecs
[ 27.297606] calling alsa_card_als4000_init+0x0/0x1b @ 1
[ 27.303087] initcall alsa_card_als4000_init+0x0/0x1b returned 0 after 100 usecs
[ 27.310467] calling alsa_card_atiixp_init+0x0/0x1b @ 1
[ 27.315864] initcall alsa_card_atiixp_init+0x0/0x1b returned 0 after 103 usecs
[ 27.323155] calling alsa_card_bt87x_init+0x0/0x30 @ 1
[ 27.328459] initcall alsa_card_bt87x_init+0x0/0x30 returned 0 after 96 usecs
[ 27.335558] calling alsa_card_cmipci_init+0x0/0x1b @ 1
[ 27.340947] initcall alsa_card_cmipci_init+0x0/0x1b returned 0 after 96 usecs
[ 27.348133] calling alsa_card_ens137x_init+0x0/0x1b @ 1
[ 27.353609] initcall alsa_card_ens137x_init+0x0/0x1b returned 0 after 95 usecs
[ 27.360900] calling alsa_card_es1968_init+0x0/0x1b @ 1
[ 27.366291] initcall alsa_card_es1968_init+0x0/0x1b returned 0 after 98 usecs
[ 27.373474] calling alsa_card_m3_init+0x0/0x1b @ 1
[ 27.378517] initcall alsa_card_m3_init+0x0/0x1b returned 0 after 95 usecs
[ 27.385356] calling alsa_card_via82xx_init+0x0/0x1b @ 1
[ 27.390832] initcall alsa_card_via82xx_init+0x0/0x1b returned 0 after 95 usecs
[ 27.398122] calling alsa_ac97_init+0x0/0x8 @ 1
[ 27.402720] initcall alsa_ac97_init+0x0/0x8 returned 0 after 0 usecs
[ 27.409119] calling alsa_card_ali_init+0x0/0x1b @ 1
[ 27.414247] initcall alsa_card_ali_init+0x0/0x1b returned 0 after 105 usecs
[ 27.421262] calling alsa_card_aw2_init+0x0/0x29 @ 1
[ 27.426291] aw2: Load aw2 module
[ 27.429671] initcall alsa_card_aw2_init+0x0/0x29 returned 0 after 3299 usecs
[ 27.436766] calling alsa_card_echo_init+0x0/0x1b @ 1
[ 27.441985] initcall alsa_card_echo_init+0x0/0x1b returned 0 after 98 usecs
[ 27.448995] calling alsa_card_echo_init+0x0/0x1b @ 1
[ 27.454215] initcall alsa_card_echo_init+0x0/0x1b returned 0 after 99 usecs
[ 27.461224] calling alsa_card_echo_init+0x0/0x1b @ 1
[ 27.466439] initcall alsa_card_echo_init+0x0/0x1b returned 0 after 95 usecs
[ 27.473453] calling alsa_card_echo_init+0x0/0x1b @ 1
[ 27.478675] initcall alsa_card_echo_init+0x0/0x1b returned 0 after 102 usecs
[ 27.485777] calling alsa_card_echo_init+0x0/0x1b @ 1
[ 27.490996] initcall alsa_card_echo_init+0x0/0x1b returned 0 after 99 usecs
[ 27.498005] calling alsa_card_hifier_init+0x0/0x1b @ 1
[ 27.503393] initcall alsa_card_hifier_init+0x0/0x1b returned 0 after 94 usecs
[ 27.510580] calling alsa_card_xonar_init+0x0/0x1b @ 1
[ 27.515889] initcall alsa_card_xonar_init+0x0/0x1b returned 0 after 101 usecs
[ 27.523078] calling alsa_card_hammerfall_init+0x0/0x1b @ 1
[ 27.528814] initcall alsa_card_hammerfall_init+0x0/0x1b returned 0 after 95 usecs
[ 27.536364] calling alsa_card_hdsp_init+0x0/0x1b @ 1
[ 27.541584] initcall alsa_card_hdsp_init+0x0/0x1b returned 0 after 99 usecs
[ 27.548592] calling snd_us122l_module_init+0x0/0x1b @ 1
[ 27.554067] usbcore: registered new interface driver snd-usb-us122l
[ 27.560390] initcall snd_us122l_module_init+0x0/0x1b returned 0 after 6270 usecs
[ 27.567862] calling alsa_sound_last_init+0x0/0x86 @ 1
[ 27.573049] ALSA device list:
[ 27.576063] No soundcards found.
[ 27.579508] initcall alsa_sound_last_init+0x0/0x86 returned 0 after 6308 usecs
[ 27.586795] calling flow_cache_init+0x0/0x12e @ 1
[ 27.591821] initcall flow_cache_init+0x0/0x12e returned 0 after 176 usecs
[ 27.598660] calling pg_init+0x0/0x2ad @ 1
[ 27.602823] pktgen v2.70: Packet Generator for packet performance testing.
[ 27.609798] initcall pg_init+0x0/0x2ad returned 0 after 6810 usecs
[ 27.616028] calling llc_init+0x0/0x20 @ 1
[ 27.620193] initcall llc_init+0x0/0x20 returned 0 after 1 usecs
[ 27.626159] calling llc2_init+0x0/0xd2 @ 1
[ 27.630435] NET: Registered protocol family 26
[ 27.634931] initcall llc2_init+0x0/0xd2 returned 0 after 4427 usecs
[ 27.641248] calling snap_init+0x0/0x33 @ 1
[ 27.645487] initcall snap_init+0x0/0x33 returned 0 after 1 usecs
[ 27.651542] calling blackhole_module_init+0x0/0x12 @ 1
[ 27.656815] initcall blackhole_module_init+0x0/0x12 returned 0 after 1 usecs
[ 27.663910] calling hfsc_init+0x0/0x12 @ 1
[ 27.668141] initcall hfsc_init+0x0/0x12 returned 0 after 0 usecs
[ 27.674197] calling prio_module_init+0x0/0x12 @ 1
[ 27.679034] initcall prio_module_init+0x0/0x12 returned 0 after 0 usecs
[ 27.685699] calling init_route4+0x0/0x12 @ 1
[ 27.690111] initcall init_route4+0x0/0x12 returned 0 after 0 usecs
[ 27.696342] calling init_basic+0x0/0x12 @ 1
[ 27.700667] initcall init_basic+0x0/0x12 returned 0 after 0 usecs
[ 27.706810] calling cls_flow_init+0x0/0x12 @ 1
[ 27.711397] initcall cls_flow_init+0x0/0x12 returned 0 after 0 usecs
[ 27.717800] calling init_em_nbyte+0x0/0x12 @ 1
[ 27.722385] initcall init_em_nbyte+0x0/0x12 returned 0 after 0 usecs
[ 27.728789] calling sysctl_ipv4_init+0x0/0x53 @ 1
[ 27.733659] initcall sysctl_ipv4_init+0x0/0x53 returned 0 after 23 usecs
[ 27.740412] calling tunnel4_init+0x0/0x6f @ 1
[ 27.744911] initcall tunnel4_init+0x0/0x6f returned 0 after 1 usecs
[ 27.751228] calling xfrm4_mode_tunnel_init+0x0/0x19 @ 1
[ 27.756595] initcall xfrm4_mode_tunnel_init+0x0/0x19 returned 0 after 1 usecs
[ 27.763776] calling inet_diag_init+0x0/0x6b @ 1
[ 27.768455] initcall inet_diag_init+0x0/0x6b returned 0 after 15 usecs
[ 27.775035] calling tcp_diag_init+0x0/0x12 @ 1
[ 27.779621] initcall tcp_diag_init+0x0/0x12 returned 0 after 1 usecs
[ 27.786023] calling cubictcp_register+0x0/0x6f @ 1
[ 27.790955] TCP cubic registered
[ 27.794231] initcall cubictcp_register+0x0/0x6f returned 0 after 3199 usecs
[ 27.801242] calling inet6_init+0x0/0x2b2 @ 1
[ 27.806489] NET: Registered protocol family 10
[ 27.811655] lo: Disabled Privacy Extensions
[ 27.816037] initcall inet6_init+0x0/0x2b2 returned 0 after 10138 usecs
[ 27.822616] calling esp6_init+0x0/0x6f @ 1
[ 27.826855] initcall esp6_init+0x0/0x6f returned 0 after 0 usecs
[ 27.832911] calling ipcomp6_init+0x0/0x6f @ 1
[ 27.837411] initcall ipcomp6_init+0x0/0x6f returned 0 after 1 usecs
[ 27.843727] calling xfrm6_tunnel_init+0x0/0xf5 @ 1
[ 27.848758] hub 2-0:1.0: hub_suspend
[ 27.852388] usb usb2: bus auto-suspend
[ 27.856247] usb usb2: suspend_rh
[ 27.859532] hub 3-0:1.0: hub_suspend
[ 27.863157] usb usb3: bus auto-suspend
[ 27.866962] usb usb3: suspend_rh
[ 27.870249] hub 4-0:1.0: hub_suspend
[ 27.873878] usb usb4: bus auto-suspend
[ 27.877681] usb usb4: suspend_rh
[ 27.880969] hub 5-0:1.0: hub_suspend
[ 27.884598] usb usb5: bus auto-suspend
[ 27.888393] usb usb5: suspend_rh
[ 27.891736] initcall xfrm6_tunnel_init+0x0/0xf5 returned 0 after 42068 usecs
[ 27.898839] calling tunnel6_init+0x0/0x6f @ 1
[ 27.903366] initcall tunnel6_init+0x0/0x6f returned 0 after 0 usecs
[ 27.909681] calling xfrm6_mode_tunnel_init+0x0/0x17 @ 1
[ 27.915046] initcall xfrm6_mode_tunnel_init+0x0/0x17 returned 0 after 0 usecs
[ 27.922229] calling xfrm6_ro_init+0x0/0x17 @ 1
[ 27.926814] initcall xfrm6_ro_init+0x0/0x17 returned 0 after 0 usecs
[ 27.933219] calling sit_init+0x0/0x76 @ 1
[ 27.937369] IPv6 over IPv4 tunneling driver
[ 27.941843] sit0: Disabled Privacy Extensions
[ 27.946284] initcall sit_init+0x0/0x76 returned 0 after 8704 usecs
[ 27.952534] calling packet_init+0x0/0x4a @ 1
[ 27.956938] NET: Registered protocol family 17
[ 27.961436] initcall packet_init+0x0/0x4a returned 0 after 4390 usecs
[ 27.967928] calling br_init+0x0/0xc6 @ 1
[ 27.972180] initcall br_init+0x0/0xc6 returned 0 after 182 usecs
[ 27.978233] calling can_init+0x0/0xf6 @ 1
[ 27.982393] can: controller area network core (rev 20090105 abi 8)
[ 27.988819] NET: Registered protocol family 29
[ 27.993316] initcall can_init+0x0/0xf6 returned 0 after 10665 usecs
[ 27.999648] calling bcm_module_init+0x0/0x6d @ 1
[ 28.004406] can: broadcast manager protocol (rev 20090105 t)
[ 28.010124] initcall bcm_module_init+0x0/0x6d returned 0 after 5582 usecs
[ 28.016965] calling af_rxrpc_init+0x0/0x1a5 @ 1
[ 28.021940] NET: Registered protocol family 33
[ 28.026450] initcall af_rxrpc_init+0x0/0x1a5 returned 0 after 4700 usecs
[ 28.033212] calling econet_proto_init+0x0/0x53 @ 1
[ 28.038137] NET: Registered protocol family 19
[ 28.042637] initcall econet_proto_init+0x0/0x53 returned 0 after 4393 usecs
[ 28.049647] calling sctp_init+0x0/0x7e3 @ 1
[ 28.054857] SCTP: Hash tables configured (established 65536 bind 65536)
[ 28.096178] sctp_init_sock(sk: ffff88007d804000)
[ 28.100868] initcall sctp_init+0x0/0x7e3 returned 0 after 45793 usecs
[ 28.107361] calling lib80211_init+0x0/0x20 @ 1
[ 28.111942] lib80211: common routines for IEEE802.11 drivers
[ 28.117655] lib80211_crypt: registered algorithm 'NULL'
[ 28.122932] initcall lib80211_init+0x0/0x20 returned 0 after 10731 usecs
[ 28.129683] calling lib80211_crypto_wep_init+0x0/0x12 @ 1
[ 28.135222] lib80211_crypt: registered algorithm 'WEP'
[ 28.140413] initcall lib80211_crypto_wep_init+0x0/0x12 returned 0 after 5068 usecs
[ 28.148048] calling lib80211_crypto_ccmp_init+0x0/0x12 @ 1
[ 28.153674] lib80211_crypt: registered algorithm 'CCMP'
[ 28.158952] initcall lib80211_crypto_ccmp_init+0x0/0x12 returned 0 after 5154 usecs
[ 28.166673] calling lib80211_crypto_tkip_init+0x0/0x12 @ 1
[ 28.172297] lib80211_crypt: registered algorithm 'TKIP'
[ 28.177577] initcall lib80211_crypto_tkip_init+0x0/0x12 returned 0 after 5155 usecs
[ 28.185297] calling tipc_init+0x0/0xc9 @ 1
[ 28.189529] TIPC: Activated (version 1.6.4 compiled Feb 8 2009 06:54:12)
[ 28.196865] NET: Registered protocol family 30
[ 28.201357] TIPC: Started in single node mode
[ 28.205780] initcall tipc_init+0x0/0xc9 returned 0 after 15870 usecs
[ 28.212183] calling rfkill_handler_init+0x0/0x49 @ 1
[ 28.217291] initcall rfkill_handler_init+0x0/0x49 returned 0 after 3 usecs
[ 28.224210] calling dcbnl_init+0x0/0x32 @ 1
[ 28.228527] initcall dcbnl_init+0x0/0x32 returned 0 after 1 usecs
[ 28.234674] calling hpet_insert_resource+0x0/0x23 @ 1
[ 28.239864] initcall hpet_insert_resource+0x0/0x23 returned 1 after 0 usecs
[ 28.246873] initcall hpet_insert_resource+0x0/0x23 returned with error code 1
[ 28.254510] calling update_mp_table+0x0/0x6c3 @ 1
[ 28.259355] initcall update_mp_table+0x0/0x6c3 returned 0 after 0 usecs
[ 28.266018] calling lapic_insert_resource+0x0/0x42 @ 1
[ 28.271302] initcall lapic_insert_resource+0x0/0x42 returned 0 after 5 usecs
[ 28.278394] calling init_lapic_nmi_sysfs+0x0/0x39 @ 1
[ 28.283587] initcall init_lapic_nmi_sysfs+0x0/0x39 returned 0 after 0 usecs
[ 28.290597] calling ioapic_insert_resources+0x0/0x59 @ 1
[ 28.296052] initcall ioapic_insert_resources+0x0/0x59 returned 0 after 1 usecs
[ 28.303337] calling io_apic_bug_finalize+0x0/0x1b @ 1
[ 28.308521] initcall io_apic_bug_finalize+0x0/0x1b returned 0 after 0 usecs
[ 28.315532] calling uv_init_heartbeat+0x0/0x19 @ 1
[ 28.320464] initcall uv_init_heartbeat+0x0/0x19 returned 0 after 0 usecs
[ 28.327215] calling check_early_ioremap_leak+0x0/0x6d @ 1
[ 28.332753] initcall check_early_ioremap_leak+0x0/0x6d returned 0 after 0 usecs
[ 28.340127] calling sched_init_debug+0x0/0x24 @ 1
[ 28.344982] initcall sched_init_debug+0x0/0x24 returned 0 after 9 usecs
[ 28.351648] calling init_oops_id+0x0/0x40 @ 1
[ 28.356147] initcall init_oops_id+0x0/0x40 returned 0 after 3 usecs
[ 28.362461] calling disable_boot_consoles+0x0/0x3a @ 1
[ 28.367739] initcall disable_boot_consoles+0x0/0x3a returned 0 after 0 usecs
[ 28.374838] calling pm_qos_power_init+0x0/0xe1 @ 1
[ 28.380443] initcall pm_qos_power_init+0x0/0xe1 returned 0 after 657 usecs
[ 28.387374] calling debugfs_kprobe_init+0x0/0x90 @ 1
[ 28.392503] initcall debugfs_kprobe_init+0x0/0x90 returned 0 after 8 usecs
[ 28.399426] calling max_swapfiles_check+0x0/0x8 @ 1
[ 28.404443] initcall max_swapfiles_check+0x0/0x8 returned 0 after 0 usecs
[ 28.411280] calling afs_init+0x0/0x1e5 @ 1
[ 28.415508] kAFS: Red Hat AFS client v0.1 registering.
[ 28.421024] initcall afs_init+0x0/0x1e5 returned 0 after 5384 usecs
[ 28.427342] calling random32_reseed+0x0/0x5d @ 1
[ 28.432134] initcall random32_reseed+0x0/0x5d returned 0 after 5 usecs
[ 28.438711] calling pci_sysfs_init+0x0/0x55 @ 1
[ 28.443626] initcall pci_sysfs_init+0x0/0x55 returned 0 after 237 usecs
[ 28.450291] calling acpi_wakeup_device_init+0x0/0x78 @ 1
[ 28.455745] initcall acpi_wakeup_device_init+0x0/0x78 returned 0 after 4 usecs
[ 28.463030] calling acpi_sleep_proc_init+0x0/0xa4 @ 1
[ 28.468264] initcall acpi_sleep_proc_init+0x0/0xa4 returned 0 after 40 usecs
[ 28.475364] calling boot_wait_for_devices+0x0/0x19 @ 1
[ 28.480643] initcall boot_wait_for_devices+0x0/0x19 returned 0 after 0 usecs
[ 28.487740] calling seqgen_init+0x0/0xf @ 1
[ 28.492075] initcall seqgen_init+0x0/0xf returned 0 after 10 usecs
[ 28.498304] calling hd_init+0x0/0x333 @ 1
[ 28.502485] hd: no drives specified - use hd=cyl,head,sectors on kernel command line
[ 28.510316] initcall hd_init+0x0/0x333 returned -1 after 7676 usecs
[ 28.516633] initcall hd_init+0x0/0x333 returned with error code -1
[ 28.522953] calling scsi_complete_async_scans+0x0/0x100 @ 1
[ 28.528663] initcall scsi_complete_async_scans+0x0/0x100 returned 0 after 0 usecs
[ 28.536213] calling rtc_hctosys+0x0/0x186 @ 1
[ 28.540709] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 28.547027] initcall rtc_hctosys+0x0/0x186 returned -19 after 6170 usecs
[ 28.553780] calling pci_mmcfg_late_insert_resources+0x0/0x166 @ 1
[ 28.560011] initcall pci_mmcfg_late_insert_resources+0x0/0x166 returned 1 after 0 usecs
[ 28.568078] initcall pci_mmcfg_late_insert_resources+0x0/0x166 returned with error code 1
[ 28.576408] calling tcp_congestion_default+0x0/0x12 @ 1
[ 28.581775] initcall tcp_congestion_default+0x0/0x12 returned 0 after 2 usecs
[ 28.588955] calling ip_auto_config+0x0/0xfdc @ 1
[ 28.593732] initcall ip_auto_config+0x0/0xfdc returned 0 after 17 usecs
[ 28.600414] async_waiting @ 1
[ 28.603422] async_continuing @ 1 after 0 usec
[ 28.622840] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 28.629253] EXT3-fs: write access will be enabled during recovery.
[ 28.816662] kjournald starting. Commit interval 5 seconds
[ 28.822217] EXT3-fs: recovery complete.
[ 28.826721] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.832725] VFS: Mounted root (ext3 filesystem) readonly on device 8:3.
[ 28.839428] async_waiting @ 1
[ 28.842448] async_continuing @ 1 after 0 usec
[ 28.846850] Freeing unused kernel memory: 660k freed
[ 31.426499] usb usb2: uevent
[ 31.439862] usb 2-0:1.0: uevent
[ 31.443363] usb usb3: uevent
[ 31.447267] usb 3-0:1.0: uevent
[ 31.450770] usb usb4: uevent
[ 31.463207] usb 4-0:1.0: uevent
[ 31.466695] usb usb5: uevent
[ 31.478429] usb 5-0:1.0: uevent
[ 31.500342] usb usb1: uevent
[ 31.503319] usb 1-0:1.0: uevent
[ 52.510805] sky2 eth0: enabling interface
[ 52.515295] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 54.905678] sky2 eth0: Link is up at 1000 Mbps, full duplex, flow control both
[ 54.913314] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 65.904007] eth0: no IPv6 routers present
[ 122.816187] EXT3 FS on sda3, internal journal
[ 123.291568] Adding 4096532k swap on /dev/sda5. Priority:-1 extents:1 across:4096532k
[ 125.023796] warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use)
[ 302.816025] Machine check events logged
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/