Re: Suspend to memory is freezing my machine

From: Jacek Luczak
Date: Sun May 04 2008 - 15:49:39 EST


Jacek Luczak pisze:
> Robert Hancock pisze:
>> Jacek Luczak wrote:
>>> Robert Hancock pisze:
>>>> Jacek Luczak wrote:
>>>>> Rafael J. Wysocki pisze:
>>>>>> On Sunday, 4 of May 2008, Zdenek Kabelac wrote:
>>>>>>> Hello
>>>>>> Hi,
>>>>>>
>>>>>>> With recent 2.6.25 & 2.6.26-rc1 git (around 1 week) I get
>>>>>>> occasionally
>>>>>>> complete freeze of my T61 during suspend. (dual core, 2GB).
>>>>>> How reproducible is this?
>>>>>>
>>>>>>> I'm running kernel with no_console_suspend - but all I can see is
>>>>>>> blinking cursor on an empty screen - thus even when I run kernel with
>>>>>>> most debug options turned on, I can't pass more details so far. I
>>>>>>> run
>>>>>>> suspend with with SD card in - so maybe some update in the MMC driver
>>>>>>> might be responsible for this ?
>>>>>>>
>>>>>>> Also - I think that option no_console_suspend doens't work
>>>>>>> correctly -
>>>>>>> as many times with suspend I do not see any log message on my console
>>>>>>> screen. However sometimes the log is shown.
>>>>>> It would be helpful if you could verify if:
>>>>>>
>>>>>> (1) The problem occurs without no_console_suspend.
>>>>>> (2) The problem occurs without the SD card.
>>>>>>
>>>>> Hi Rafael,
>>>>>
>>>>> same problem here, although I was able to resume system (it's
>>>>> basically Intel
>>>>> machine) , but it was unusable - I was able to switch between
>>>>> terminals and see
>>>>> output from kernel. So there was:
>>>>> - Disabling irq #19;
>>>>> - some kind of lock spinning on disk:
>>>>> IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA
>>>>> Storage
>>>>> Controller IDE (rev 02)
>>>>> but I can't provide more output of that lock now - no sign in logs.
>>>>>
>>>>> I've made some successful suspend/resume all without sound card active
>>>>> without
>>>>> problem. Those appear with sound card active, but I must take closer
>>>>> look - will
>>>>> send info later.
>>>> Can you post your dmesg and /proc/interrupts output from normal bootup ?
>>> Sure I can ;)
>>>
>>> 1) /proc/interrupts
>>>
>>> CPU0 CPU1
>>> 0: 11846981 0 IO-APIC-edge timer
>>> 1: 30098 0 IO-APIC-edge i8042
>>> 8: 3 0 IO-APIC-edge rtc
>>> 9: 13 0 IO-APIC-fasteoi acpi
>>> 12: 1776540 0 IO-APIC-edge i8042
>>> 14: 39 0 IO-APIC-edge ata_piix
>>> 15: 0 0 IO-APIC-edge ata_piix
>>> 16: 54570 44642 IO-APIC-fasteoi i915@pci:0000:00:02.0
>>> 17: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
>>> 18: 0 0 IO-APIC-fasteoi uhci_hcd:usb4
>>> 19: 98243 0 IO-APIC-fasteoi ata_piix, uhci_hcd:usb5
>>> 21: 1650574 0 IO-APIC-fasteoi HDA Intel
>>> 23: 0 0 IO-APIC-fasteoi ehci_hcd:usb1,
>>> uhci_hcd:usb2
>>> 220: 14263 0 PCI-MSI-edge iwl3945
>>> 221: 1166041 1333296 PCI-MSI-edge eth0
>>> NMI: 0 0 Non-maskable interrupts
>>> LOC: 1104887 7534969 Local timer interrupts
>>> RES: 633378 701351 Rescheduling interrupts
>>> CAL: 16 28315 function call interrupts
>>> TLB: 1721 2620 TLB shootdowns
>>> TRM: 0 0 Thermal event interrupts
>>> SPU: 0 0 Spurious interrupts
>>> ERR: 0
>>> MIS: 0
>>>
>>> 2) dmesg can here -> http://212.109.128.251/~difrost/linux-next/dmesg.log
>>> 3) Kernel:
>>> Linux difrost 2.6.25-07422-gb66e1f1-dirty #14 SMP Fri May 2 22:04:17
>>> CEST 2008
>>> i686 i686 i386 GNU/Linux
>>> It's marked dirty because due to http://lkml.org/lkml/2008/5/2/405
>>> patch applied.
>>>
>>> -Jacek
>>>
>> Well, if IRQ 19 got disabled, that's your SATA controller, so resume
>> likely isn't going to work. Could be a libata problem? CCing linux-ide.
>
> Yep, I know, that's why I pointed that out. Irq was disabled somehow in suspend
> or resume process.
>
>> BTW, if your BIOS offers an option to enable AHCI on your SATA
>> controller then that would be a more optimal configuration (could get
>> NCQ support), but that is an aside.
>
> With AHCI I've got pretty bad timings (and I don't really know why!):
>
> [root|20:49|~]$ cat sda_ahci_t
>
> /dev/sda:
> Timing cached reads: 1560 MB in 2.00 seconds = 780.51 MB/sec
> Timing buffered disk reads: 102 MB in 3.02 seconds = 33.74 MB/sec
> [root|20:49|~]$ cat sda_piix_t
>
> /dev/sda:
> Timing cached reads: 1544 MB in 2.00 seconds = 772.35 MB/sec
> Timing buffered disk reads: 134 MB in 3.04 seconds = 44.05 MB/sec

Here's the latest report (all on latest git):
1) I've switched to AHCI mode and suspend/resume works OK (because SATA
controller irq is not disabled).

2) now /proc/interrupts look like that:
CPU0 CPU1
0: 110708 0 IO-APIC-edge timer
1: 4008 0 IO-APIC-edge i8042
8: 3 0 IO-APIC-edge rtc
9: 15091 0 IO-APIC-fasteoi acpi
12: 77467 0 IO-APIC-edge i8042
14: 44 0 IO-APIC-edge ata_piix
15: 0 0 IO-APIC-edge ata_piix
16: 0 0 IO-APIC-fasteoi i915@pci:0000:00:02.0
17: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
18: 0 0 IO-APIC-fasteoi uhci_hcd:usb4
19: 100001 0 IO-APIC-fasteoi uhci_hcd:usb5
21: 282 0 IO-APIC-fasteoi HDA Intel
23: 1 0 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb2
219: 858 0 PCI-MSI-edge iwl3945
220: 8616 0 PCI-MSI-edge eth0
221: 6423 0 PCI-MSI-edge ahci
NMI: 0 0 Non-maskable interrupts
LOC: 15777 64510 Local timer interrupts
RES: 9045 24560 Rescheduling interrupts
CAL: 30 28255 function call interrupts
TLB: 341 145 TLB shootdowns
TRM: 0 0 Thermal event interrupts
SPU: 0 0 Spurious interrupts
ERR: 0
MIS: 0

3) The IRQ #19 remains disabled after resume and produce:
irq 19: nobody cared (try booting with the "irqpoll" option)
Pid: 13, comm: kacpi_notify Not tainted 2.6.26-rc1-07561-gafa26be-dirty #16
[<c013ea27>] __report_bad_irq+0x24/0x69
[<c013ea2e>] __report_bad_irq+0x2b/0x69
[<c013ec25>] note_interrupt+0x1b9/0x210
[<c013e36c>] handle_IRQ_event+0x1a/0x3f
[<c013f195>] handle_fasteoi_irq+0x84/0xa2
[<c0104fde>] do_IRQ+0x4f/0x65
[<c01034ff>] common_interrupt+0x23/0x28
[<c013007b>] timekeeping_resume+0x9b/0x127
[<c020b090>] acpi_os_read_port+0x29/0x44
[<c02177c9>] acpi_hw_register_read+0x61/0x119
[<c020f76e>] acpi_ev_fixed_event_detect+0x2a/0xa0
[<c021001a>] acpi_ev_sci_xrupt_handler+0x9/0x17
[<c020b053>] acpi_irq+0xb/0x1f
[<c013e36c>] handle_IRQ_event+0x1a/0x3f
[<c013f181>] handle_fasteoi_irq+0x70/0xa2
[<c0104fde>] do_IRQ+0x4f/0x65
[<c020b623>] acpi_os_execute_deferred+0x0/0x25
[<c01034ff>] common_interrupt+0x23/0x28
[<c020b623>] acpi_os_execute_deferred+0x0/0x25
[<c020b0b8>] acpi_os_write_port+0xd/0x2c
[<c020b640>] acpi_os_execute_deferred+0x1d/0x25
[<c01290fa>] run_workqueue+0x69/0xda
[<c0129221>] worker_thread+0xb6/0xc2
[<c012bca6>] autoremove_wake_function+0x0/0x2d
[<c012916b>] worker_thread+0x0/0xc2
[<c012ba42>] kthread+0x38/0x5d
[<c012ba0a>] kthread+0x0/0x5d
[<c010370f>] kernel_thread_helper+0x7/0x10
=======================
handlers:
[<c027d100>] (usb_hcd_irq+0x0/0x53)
Disabling IRQ #19

This might happen due to "ACPI: EC: GPE storm detected, disabling EC GPE", but
here it should revert to polling mode (which is done during boot, but not during
resume). I'm not expert here.

Full dmesg here -> http://212.109.128.251/~difrost/linux-next/dmesg_ahci.log

-Jacek

PS: Site note: Why there's such big difference on hdparm timings with PATA and
AHCI mode?
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/