[PATCH 1/1] [MTD/MAPS] Blackfin BF5xx Maps: Handle the case where flash memory and ethernet mac/phy are mapped onto the same async bank

From: Bryan Wu
Date: Wed Jan 30 2008 - 05:02:59 EST


The BF533-STAMP does this for example.
All board-specific configuration goes in your board resources file.

Signed-off-by: Mike Frysinger <michael.frysinger@xxxxxxxxxx>
Signed-off-by: Bryan Wu <bryan.wu@xxxxxxxxxx>
---
drivers/mtd/maps/Kconfig | 45 ++++++++
drivers/mtd/maps/Makefile | 1 +
drivers/mtd/maps/bf5xx-flash.c | 227 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 273 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/maps/bf5xx-flash.c

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index a592fc0..5357f04 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -528,6 +528,51 @@ config MTD_PCMCIA_ANONYMOUS

If unsure, say N.

+config MTD_BF5xx
+ tristate "Blackfin BF533-STAMP Flash Chip Support"
+ depends on BFIN533_STAMP && MTD_CFI
+ select MTD_PARTITIONS
+ help
+ Map driver which allows for simultaneous utilization of
+ ethernet and CFI parallel flash.
+
+config BFIN_FLASH_BANK_0
+ hex "EBIU_AMBCTL For Flash (Bank 0)"
+ depends on MTD_BF5xx
+ default 0x7BB0
+ help
+ For boards that share the async memory bank with both Flash and
+ the Ethernet, these settings allow you to have EBIU settings just
+ when the Flash is active. The other EBIU settings in the main
+ Blackfin menu will be utilized when the Flash is not active.
+config BFIN_FLASH_BANK_1
+ hex "EBIU_AMBCTL For Flash (Bank 1)"
+ depends on MTD_BF5xx
+ default 0x7BB0
+ help
+ For boards that share the async memory bank with both Flash and
+ the Ethernet, these settings allow you to have EBIU settings just
+ when the Flash is active. The other EBIU settings in the main
+ Blackfin menu will be utilized when the Flash is not active.
+config BFIN_FLASH_BANK_2
+ hex "EBIU_AMBCTL For Flash (Bank 2)"
+ depends on MTD_BF5xx
+ default 0x7BB0
+ help
+ For boards that share the async memory bank with both Flash and
+ the Ethernet, these settings allow you to have EBIU settings just
+ when the Flash is active. The other EBIU settings in the main
+ Blackfin menu will be utilized when the Flash is not active.
+config BFIN_FLASH_BANK_3
+ hex "EBIU_AMBCTL For Flash (Bank 3)"
+ depends on MTD_BF5xx
+ default 0x7BB0
+ help
+ For boards that share the async memory bank with both Flash and
+ the Ethernet, these settings allow you to have EBIU settings just
+ when the Flash is active. The other EBIU settings in the main
+ Blackfin menu will be utilized when the Flash is not active.
+
config MTD_UCLINUX
tristate "Generic uClinux RAM/ROM filesystem support"
depends on MTD_PARTITIONS && !MMU
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
index 316382a..62eea4f 100644
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -69,3 +69,4 @@ obj-$(CONFIG_MTD_PLATRAM) += plat-ram.o
obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
obj-$(CONFIG_MTD_INTEL_VR_NOR) += intel_vr_nor.o
+obj-$(CONFIG_MTD_BF5xx) += bf5xx-flash.o
diff --git a/drivers/mtd/maps/bf5xx-flash.c b/drivers/mtd/maps/bf5xx-flash.c
new file mode 100644
index 0000000..8c2f897
--- /dev/null
+++ b/drivers/mtd/maps/bf5xx-flash.c
@@ -0,0 +1,227 @@
+/*
+ * drivers/mtd/maps/bf5xx-flash.c
+ *
+ * Handle the case where flash memory and ethernet mac/phy are
+ * mapped onto the same async bank. The BF533-STAMP does this
+ * for example. All board-specific configuration goes in your
+ * board resources file.
+ *
+ * Copyright 2000 Nicolas Pitre <nico@xxxxxxx>
+ * Copyright 2005-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#include <asm/blackfin.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/unaligned.h>
+
+#define pr_init(fmt, args...) ({ static const __initdata char __fmt[] = fmt; printk(__fmt, ## args); })
+
+#define DRIVER_NAME "BF5xx-Flash"
+
+#define BFIN_FLASH_AMBCTL0VAL ((CONFIG_BFIN_FLASH_BANK_1 << 16) | CONFIG_BFIN_FLASH_BANK_0)
+#define BFIN_FLASH_AMBCTL1VAL ((CONFIG_BFIN_FLASH_BANK_3 << 16) | CONFIG_BFIN_FLASH_BANK_2)
+
+/* Should add a per-device structure and track this there ... */
+static int enet_flash_pin;
+static struct mtd_info *bf5xx_mtd;
+
+struct flash_save {
+ u32 ambctl0;
+ u32 ambctl1;
+ unsigned long flags;
+};
+
+static void switch_to_flash(struct flash_save *save)
+{
+ local_irq_save(save->flags);
+
+ gpio_set_value(enet_flash_pin, 0);
+ SSYNC();
+
+ save->ambctl0 = bfin_read_EBIU_AMBCTL0();
+ save->ambctl1 = bfin_read_EBIU_AMBCTL1();
+ bfin_write_EBIU_AMBCTL0(BFIN_FLASH_AMBCTL0VAL);
+ bfin_write_EBIU_AMBCTL1(BFIN_FLASH_AMBCTL1VAL);
+ SSYNC();
+}
+
+static void switch_back(struct flash_save *save)
+{
+ bfin_write_EBIU_AMBCTL0(save->ambctl0);
+ bfin_write_EBIU_AMBCTL1(save->ambctl1);
+ SSYNC();
+
+ gpio_set_value(enet_flash_pin, 1);
+
+ local_irq_restore(save->flags);
+}
+
+static map_word bf5xx_read(struct map_info *map, unsigned long ofs)
+{
+ int nValue = 0x0;
+ map_word test;
+ struct flash_save save;
+
+ switch_to_flash(&save);
+ SSYNC();
+ nValue = readw(map->virt + ofs);
+ SSYNC();
+ switch_back(&save);
+
+ test.x[0] = (u16)nValue;
+ return test;
+}
+
+static void bf5xx_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+ unsigned long i;
+ map_word test;
+
+ if ((unsigned long)to & 0x1) {
+ for (i = 0; i < len / 2 * 2; i += 2) {
+ test = bf5xx_read(map, from + i);
+ put_unaligned(test.x[0], (__le16 *)(to + i));
+ }
+ } else {
+ for (i = 0; i < len / 2 * 2; i += 2) {
+ test = bf5xx_read(map, from + i);
+ *((u16*)(to + i)) = test.x[0];
+ }
+ }
+
+ if (len & 0x1) {
+ test = bf5xx_read(map, from + i);
+ *((u8*)(to + i)) = (u8)test.x[0];
+ }
+}
+
+static void bf5xx_write(struct map_info *map, map_word d1, unsigned long ofs)
+{
+ u16 d;
+ struct flash_save save;
+
+ d = (u16)d1.x[0];
+
+ switch_to_flash(&save);
+
+ SSYNC();
+ writew(d, map->virt + ofs);
+ SSYNC();
+
+ switch_back(&save);
+}
+
+static void bf5xx_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+ struct flash_save save;
+
+ switch_to_flash(&save);
+
+ memcpy(map->virt + to, from, len);
+
+ switch_back(&save);
+}
+
+static struct map_info bf5xx_map = {
+ .name = DRIVER_NAME,
+ .read = bf5xx_read,
+ .copy_from = bf5xx_copy_from,
+ .write = bf5xx_write,
+ .copy_to = bf5xx_copy_to,
+};
+
+#ifdef CONFIG_MTD_PARTITIONS
+static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL };
+#endif
+
+static int __init bf5xx_flash_probe(struct platform_device *dev)
+{
+ int ret;
+ struct physmap_flash_data *pdata = dev->dev.platform_data;
+ struct resource *memory = platform_get_resource(dev, IORESOURCE_MEM, 0);
+
+ enet_flash_pin = platform_get_irq(dev, 0);
+
+ bf5xx_map.bankwidth = pdata->width;
+ bf5xx_map.size = memory->end - memory->start + 1;
+ bf5xx_map.virt = (void __iomem *)memory->start;
+ bf5xx_map.phys = memory->start;
+
+ if (gpio_request(enet_flash_pin, DRIVER_NAME)) {
+ pr_init(KERN_ERR DRIVER_NAME ": Failed to request gpio %d\n", enet_flash_pin);
+ return -EBUSY;
+ }
+ gpio_direction_output(enet_flash_pin, 1);
+
+ pr_init(KERN_NOTICE DRIVER_NAME ": probing %d-bit flash bus\n", bf5xx_map.bankwidth * 8);
+ bf5xx_mtd = do_map_probe(memory->name, &bf5xx_map);
+ if (!bf5xx_mtd)
+ return -ENXIO;
+
+#ifdef CONFIG_MTD_PARTITIONS
+ ret = parse_mtd_partitions(bf5xx_mtd, part_probe_types, &pdata->parts, 0);
+ if (ret > 0) {
+ pr_init(KERN_NOTICE DRIVER_NAME ": Using commandline partition definition\n");
+ add_mtd_partitions(bf5xx_mtd, pdata->parts, ret);
+
+ } else if (pdata->nr_parts) {
+ pr_init(KERN_NOTICE DRIVER_NAME ": Using board partition definition\n");
+ add_mtd_partitions(bf5xx_mtd, pdata->parts, pdata->nr_parts);
+
+ } else
+#endif
+ {
+ pr_init(KERN_NOTICE DRIVER_NAME ": no partition info available, registering whole flash at once\n");
+ add_mtd_device(bf5xx_mtd);
+ }
+
+ return 0;
+}
+
+static int __devexit bf5xx_flash_remove(struct platform_device *dev)
+{
+ gpio_free(enet_flash_pin);
+#ifdef CONFIG_MTD_PARTITIONS
+ del_mtd_partitions(bf5xx_mtd);
+#endif
+ map_destroy(bf5xx_mtd);
+ return 0;
+}
+
+static struct platform_driver bf5xx_flash_driver = {
+ .probe = bf5xx_flash_probe,
+ .remove = __devexit_p(bf5xx_flash_remove),
+ .driver = {
+ .name = DRIVER_NAME,
+ },
+};
+
+static int __init bf5xx_flash_init(void)
+{
+ return platform_driver_register(&bf5xx_flash_driver);
+}
+module_init(bf5xx_flash_init);
+
+static void __exit bf5xx_flash_exit(void)
+{
+ platform_driver_unregister(&bf5xx_flash_driver);
+}
+module_exit(bf5xx_flash_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MTD map driver for Blackfins with flash/ethernet on same async bank");
--
1.5.3.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/