Re: Marvell 88E8056 gigabit ethernet controller

[Willy Tarreau]

On Fri, Aug 17, 2007 at 05:03:41PM -0700, Stephen Hemminger wrote:
> On Fri, 17 Aug 2007 05:42:13 -0700 (PDT)
> Kevin E <kevin360@xxxxxxxxx> wrote:
> 
> > Hi all,
> > 
> > 	I've read where the onboard Marvell lan controller on
> > some Gigabyte boards don't work.  I've got two systems
> > using the same Gigabyte board, on one the LAN works on
> > the other it dies like described by others.  Here's
> > the systems:
> > 
> > 
> > Working system:
> > Gigabyte 965P-DS3 rev 3.3  (BIOS F10)
> > Core2 Q6600
> > 2GB Corsair XMS2 memory
> > kernel 2.6.22.3
> > 
> > lspci for LAN controller:
> > 04:00.0 Ethernet controller: Marvell Technology Group
> > Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev
> > 14)
> > 
> > 
> > Broken system:
> > Gigabyte 965P-DS3 rev 3.3  (BIOS F10)
> > Core2 E4400
> > 2GB Corsair XMS2 memory
> > kernel 2.6.22.3
> > 
> > lspci for LAN controller:
> > 03:00.0 Ethernet controller: Marvell Technology Group
> > Ltd. Unknown device 4364 (rev 12)
> > 
> > 
> > 	The BIOS for the two systems are setup the same and
> > the config for the kernels are the same too.  I've
> > actually tried taking the kernel from the working
> > system and booting it on the broken one but still the
> > LAN dies after a couple of seconds.  The working
> > system has one card plugged in (nvidia based PCI-X
> > video card), I've taken that card and plugged into the
> > broken system, booted the same kernel, and it still
> > dies after a while.
> > 
> > 	I will gladly provide any info needed if it can help
> > in getting this chipset working on the Gigabyte
> > boards.
> > 
> > 	Thanks,
> > 	Kevin
> 
> I maintain the sky2 driver, and have one of the (buggy) Gigabyte motherboards.
> It is interesting that the problem seems to track with video card.

No Stephen, look again, he says that moving the video card into the broken
system does not change anything.

> Are you using the Nvidia binary driver?
> The video card in the system I have troubles with is:
> 	ATI Technologies Inc RV370 [Radeon X300SE]
> 
> Surprisingly, using other PCI-E cards with same driver (different Marvell chips)
> has no problem.  Vendor version of sk98lin driver has same failure mode
> on the buggy hardware.
> 
> You might want to look at lspci -vvv output on two system to see if there
> are differences. Perhaps there is a CPU speed dependency?

I don't understand why the working one is on PCI bus 3 while the other
is on PCI bus 4. It's just as if the chip embedded a PCI bridge. Maybe
those chips are just cheaper dual-channel controllers with one faulty
controller disabled. It would also explain why the PCI ID is different.

Willy

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/