Subject: [PATCH 2.6.20 003/005] [RESEND v2] dmfe: Fix link detection

From: Maxim
Date: Thu Feb 15 2007 - 16:08:44 EST


From: Maxim Levitsky <maximlevitsky@xxxxxxxxx>
Subject: [PATCH 2.6.20 003/005] [RESEND v2] dmfe: Fix link detection

Add link detection

Signed-off-by: Maxim Levitsky <maximlevitsky@xxxxxxxxx>

---

--- linux-2.6.20-mod/drivers/net/tulip/dmfe.c 2007-02-15 18:00:58.000000000 +0200
+++ linux-2.6.20-test/drivers/net/tulip/dmfe.c 2007-02-15 18:21:28.000000000 +0200
@@ -248,7 +248,6 @@ struct dmfe_board_info {
u8 media_mode; /* user specify media mode */
u8 op_mode; /* real work media mode */
u8 phy_addr;
- u8 link_failed; /* Ever link failed */
u8 wait_reset; /* Hardware failed, need to reset */
u8 dm910x_chk_mode; /* Operating mode check */
u8 first_in_callback; /* Flag to record state */
@@ -447,6 +446,7 @@ static int __devinit dmfe_init_one (stru
dev->poll_controller = &poll_dmfe;
#endif
dev->ethtool_ops = &netdev_ethtool_ops;
+ netif_carrier_off(dev);
spin_lock_init(&db->lock);

pci_read_config_dword(pdev, 0x50, &pci_pmr);
@@ -541,7 +541,6 @@ static int dmfe_open(struct DEVICE *dev)
db->tx_packet_cnt = 0;
db->tx_queue_cnt = 0;
db->rx_avail_cnt = 0;
- db->link_failed = 1;
db->wait_reset = 0;

db->first_in_callback = 0;
@@ -1082,6 +1081,7 @@ static void netdev_get_drvinfo(struct ne

static const struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
+ .get_link = ethtool_op_get_link,
};

/*
@@ -1097,6 +1097,8 @@ static void dmfe_timer(unsigned long dat
struct dmfe_board_info *db = netdev_priv(dev);
unsigned long flags;

+ int link_ok, link_ok_phy;
+
DMFE_DBUG(0, "dmfe_timer()", 0);
spin_lock_irqsave(&db->lock, flags);

@@ -1168,15 +1170,35 @@ static void dmfe_timer(unsigned long dat
(db->chip_revision == 0x02000010)) ) {
/* DM9102A Chip */
if (tmp_cr12 & 2)
- tmp_cr12 = 0x0; /* Link failed */
+ link_ok = 0;
else
- tmp_cr12 = 0x3; /* Link OK */
+ link_ok = 1;
}
+ else
+ /*0x43 is used instead of 0x3 because bit 6 should represent
+ link status of external PHY */
+ link_ok = (tmp_cr12 & 0x43) ? 1 : 0;
+
+
+ /* If chip reports that link is failed it could be because external
+ PHY link status pin is not conected correctly to chip
+ To be sure ask PHY too.
+ */
+
+ /* need a dummy read because of PHY's register latch*/
+ phy_read (db->ioaddr, db->phy_addr, 1, db->chip_id);
+ link_ok_phy = (phy_read (db->ioaddr,
+ db->phy_addr, 1, db->chip_id) & 0x4) ? 1 : 0;
+
+ if (link_ok_phy != link_ok) {
+ DMFE_DBUG (0, "PHY and chip report different link status", 0);
+ link_ok = link_ok | link_ok_phy;
+ }

- if ( !(tmp_cr12 & 0x3) && !db->link_failed ) {
+ if ( !link_ok && netif_carrier_ok(dev)) {
/* Link Failed */
DMFE_DBUG(0, "Link Failed", tmp_cr12);
- db->link_failed = 1;
+ netif_carrier_off(dev);

/* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */
/* AUTO or force 1M Homerun/Longrun don't need */
@@ -1191,19 +1213,19 @@ static void dmfe_timer(unsigned long dat
db->cr6_data&=~0x00000200; /* bit9=0, HD mode */
update_cr6(db->cr6_data, db->ioaddr);
}
- } else
- if ((tmp_cr12 & 0x3) && db->link_failed) {
- DMFE_DBUG(0, "Link link OK", tmp_cr12);
- db->link_failed = 0;
-
- /* Auto Sense Speed */
- if ( (db->media_mode & DMFE_AUTO) &&
- dmfe_sense_speed(db) )
- db->link_failed = 1;
- dmfe_process_mode(db);
- /* SHOW_MEDIA_TYPE(db->op_mode); */
+ } else if (!netif_carrier_ok(dev)) {
+
+ DMFE_DBUG(0, "Link link OK", tmp_cr12);
+
+ /* Auto Sense Speed */
+ if ( !(db->media_mode & DMFE_AUTO) || !dmfe_sense_speed(db)) {
+ netif_carrier_on(dev);
+ SHOW_MEDIA_TYPE(db->op_mode);
}

+ dmfe_process_mode(db);
+ }
+
/* HPNA remote command check */
if (db->HPNA_command & 0xf00) {
db->HPNA_timer--;
@@ -1248,7 +1270,7 @@ static void dmfe_dynamic_reset(struct DE
db->tx_packet_cnt = 0;
db->tx_queue_cnt = 0;
db->rx_avail_cnt = 0;
- db->link_failed = 1;
+ netif_carrier_off(dev);
db->wait_reset = 0;

/* Re-initilize DM910X board */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/