Re: [PATCH] OMAP: I2C driver for TI OMAP boards #2

From: Jean Delvare
Date: Wed Aug 02 2006 - 11:32:06 EST


Hi Komal,

> Updated driver patch based on the review comments from David Brownell.
>
> >That #define of MODULE_NAME should be removed; useless/unused.
> >And the #ifdefs for 15xx should be cpu-is-15xx type tests.

Here comes my review.

> This patch adds I2C bus driver for various Texas
> Instruments (TI) OMAP1/2 (http://www.ti.com/omap) series
> based boards like OMAP1510/1610/1710/242x.
>
> Signed-off-by: Komal Shah <komal_shah802003@xxxxxxxxx>
>
> ---
>
> drivers/i2c/busses/Kconfig | 7
> drivers/i2c/busses/Makefile | 1
> drivers/i2c/busses/i2c-omap.c | 712 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 720 insertions(+), 0 deletions(-)
> create mode 100644 drivers/i2c/busses/i2c-omap.c
>
> bfd0caa110e5912e38a113983119d96c173fa083
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 884320e..bf49c97 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -537,4 +537,11 @@ config I2C_MV64XXX
> This driver can also be built as a module. If so, the module
> will be called i2c-mv64xxx.
>
> +config I2C_OMAP
> + tristate "OMAP I2C adapter"
> + depends on I2C && ARCH_OMAP
> + default y if MACH_OMAP_H3 || MACH_OMAP_OSK
> + help
> + Support for TI OMAP I2C driver. Say yes if you want to use the OMAP
> + I2C interface.
> endmenu

In alphabetical order, please. I see that some recent entries broke the
rule... This needs to be fixed.

"Support for TI OMAP I2C driver" doesn't make much sense.

> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index ac56df5..2fd82e4 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -43,6 +43,7 @@ obj-$(CONFIG_I2C_VIAPRO) += i2c-viapro.o
> obj-$(CONFIG_I2C_VOODOO3) += i2c-voodoo3.o
> obj-$(CONFIG_SCx200_ACB) += scx200_acb.o
> obj-$(CONFIG_SCx200_I2C) += scx200_i2c.o
> +obj-$(CONFIG_I2C_OMAP) += i2c-omap.o
>
> ifeq ($(CONFIG_I2C_DEBUG_BUS),y)
> EXTRA_CFLAGS += -DDEBUG

Alphabetical order here too, please.

> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> new file mode 100644
> index 0000000..2cdecd5
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -0,0 +1,712 @@
> +/*
> + * linux/drivers/i2c/busses/i2c-omap.c

Don't include the full path here. At best it is redundant, at worst in
tends to become wrong over time as we move and/or rename driver.

> + *
> + * TI OMAP I2C master mode driver
> + *
> + * Copyright (C) 2003 MontaVista Software, Inc.
> + * Copyright (C) 2004 Texas Instruments.
> + *
> + * Updated to work with multiple I2C interfaces on 24xx by
> + * Tony Lindgren <tony@xxxxxxxxxxx> and Imre Deak <imre.deak@xxxxxxxxx>
> + * Copyright (C) 2005 Nokia Corporation
> + *
> + * Cleaned up by Juha Yrjölä <juha.yrjola@xxxxxxxxx>
> + *
> + * ----------------------------------------------------------------------------
> + * This file was highly leveraged from i2c-elektor.c:
> + *
> + * Copyright 1995-97 Simon G. Vogl
> + * 1998-99 Hans Berglund
> + *
> + * With some changes from Kyösti Mälkki <kmalkki@xxxxxxxxx> and even
> + * Frodo Looijaard <frodol@xxxxxx>

Please drop this highly generic and irrelevant paragraph.

> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +// #define DEBUG

Drop (debugging can be enabled with Kconfig).

> +
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/err.h>
> +#include <linux/interrupt.h>
> +#include <linux/completion.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +
> +#include <asm/io.h>
> +
> +/* ----- global defines ----------------------------------------------- */
> +static const char driver_name[] = "i2c_omap";
> +
> +#define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000)) /* timeout waiting for the controller to respond */

Line too long, please move the comment on its own line.

> +
> +#define DEFAULT_OWN 1 /* default own I2C address */

Bad choice, 1 is a reserved address for I2C (CBUS address).

> +#define MAX_MESSAGES 65536 /* max number of messages */

This is a unreasonably high limit. I don't see the point in having a
limit anyway.

> +
> +#define OMAP_I2C_REV_REG 0x00
> +#define OMAP_I2C_IE_REG 0x04
> +#define OMAP_I2C_STAT_REG 0x08
> +#define OMAP_I2C_IV_REG 0x0c
> +#define OMAP_I2C_SYSS_REG 0x10
> +#define OMAP_I2C_BUF_REG 0x14
> +#define OMAP_I2C_CNT_REG 0x18
> +#define OMAP_I2C_DATA_REG 0x1c
> +#define OMAP_I2C_SYSC_REG 0x20
> +#define OMAP_I2C_CON_REG 0x24
> +#define OMAP_I2C_OA_REG 0x28
> +#define OMAP_I2C_SA_REG 0x2c
> +#define OMAP_I2C_PSC_REG 0x30
> +#define OMAP_I2C_SCLL_REG 0x34
> +#define OMAP_I2C_SCLH_REG 0x38
> +#define OMAP_I2C_SYSTEST_REG 0x3c
> +
> +/* I2C Interrupt Enable Register (OMAP_I2C_IE): */
> +#define OMAP_I2C_IE_XRDY (1 << 4) /* TX data ready int enable */
> +#define OMAP_I2C_IE_RRDY (1 << 3) /* RX data ready int enable */
> +#define OMAP_I2C_IE_ARDY (1 << 2) /* Access ready int enable */
> +#define OMAP_I2C_IE_NACK (1 << 1) /* No ack interrupt enable */
> +#define OMAP_I2C_IE_AL (1 << 0) /* Arbitration lost int ena */
> +
> +/* I2C Status Register (OMAP_I2C_STAT): */
> +#define OMAP_I2C_STAT_SBD (1 << 15) /* Single byte data */
> +#define OMAP_I2C_STAT_BB (1 << 12) /* Bus busy */
> +#define OMAP_I2C_STAT_ROVR (1 << 11) /* Receive overrun */
> +#define OMAP_I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
> +#define OMAP_I2C_STAT_AAS (1 << 9) /* Address as slave */
> +#define OMAP_I2C_STAT_AD0 (1 << 8) /* Address zero */
> +#define OMAP_I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
> +#define OMAP_I2C_STAT_RRDY (1 << 3) /* Receive data ready */
> +#define OMAP_I2C_STAT_ARDY (1 << 2) /* Register access ready */
> +#define OMAP_I2C_STAT_NACK (1 << 1) /* No ack interrupt enable */
> +#define OMAP_I2C_STAT_AL (1 << 0) /* Arbitration lost int ena */
> +
> +/* I2C Buffer Configuration Register (OMAP_I2C_BUF): */
> +#define OMAP_I2C_BUF_RDMA_EN (1 << 15) /* RX DMA channel enable */
> +#define OMAP_I2C_BUF_XDMA_EN (1 << 7) /* TX DMA channel enable */
> +
> +/* I2C Configuration Register (OMAP_I2C_CON): */
> +#define OMAP_I2C_CON_EN (1 << 15) /* I2C module enable */
> +#define OMAP_I2C_CON_BE (1 << 14) /* Big endian mode */
> +#define OMAP_I2C_CON_STB (1 << 11) /* Start byte mode (master) */
> +#define OMAP_I2C_CON_MST (1 << 10) /* Master/slave mode */
> +#define OMAP_I2C_CON_TRX (1 << 9) /* TX/RX mode (master only) */
> +#define OMAP_I2C_CON_XA (1 << 8) /* Expand address */
> +#define OMAP_I2C_CON_RM (1 << 2) /* Repeat mode (master only) */
> +#define OMAP_I2C_CON_STP (1 << 1) /* Stop cond (master only) */
> +#define OMAP_I2C_CON_STT (1 << 0) /* Start condition (master) */
> +
> +/* I2C System Test Register (OMAP_I2C_SYSTEST): */
> +#define OMAP_I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
> +#define OMAP_I2C_SYSTEST_FREE (1 << 14) /* Free running mode */
> +#define OMAP_I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
> +#define OMAP_I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
> +#define OMAP_I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense in */
> +#define OMAP_I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive out */
> +#define OMAP_I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense in */
> +#define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */

You don't use the system test register anywhere, so these bit
definitions are useless, as is the definition of the register itself.

> +
> +/* I2C System Status register (OMAP_I2C_SYSS): */
> +#define OMAP_I2C_SYSS_RDONE 1 /* Reset Done */

Not used anywhere?

> +
> +/* I2C System Configuration Register (OMAP_I2C_SYSC): */
> +#define OMAP_I2C_SYSC_SRST (1 << 1) /* Soft Reset */
> +
> +/* REVISIT: Use platform_data instead of module parameters */
> +static int clock = 100; /* Default: Fast Mode = 400 KHz, Standard = 100 KHz */

This comment is confusing, it sounds like 400 is the default.

Also, the proper unit symbol is kHz, not KHz.

> +module_param(clock, int, 0);
> +MODULE_PARM_DESC(clock, "Set I2C clock in kHz: 100 or 400 (Fast Mode)");

Might be worth mentioning here that 100 is the default.

> +
> +static int own;
> +module_param(own, int, 0);
> +MODULE_PARM_DESC(own, "Address of OMAP I2C master (0 for default == 1)");

The comment is confusing, as this address is usually known as the
"slave address" in the I2C world. Masters don't need no address on an
I2C bus. "own" is not a very explicit parameter name, what about
"slave_addr"? Ideally this should be retrieved from platform_data too,
else you can't be sure you won't collide with a device on the bus.

"0 for default" doesn't make sense, as the default is, by definition,
when the user doesn't speficiy anything. That this is internally coded
as 0 is an implementation detail user-space doesn't need to know.

This could be made an unsigned short, too.

> +
> +struct omap_i2c_dev {
> + struct device *dev;
> + void __iomem *base; /* virtual */
> + int irq;
> + struct clk *iclk; /* Interface clock */
> + struct clk *fclk; /* Functional clock */
> + struct completion cmd_complete;
> + u16 cmd_err;
> + u8 *buf;
> + size_t buf_len;
> + struct i2c_adapter adapter;
> + unsigned rev1:1;
> + u8 own_address;
> +};
> +
> +static inline void omap_i2c_write_reg(struct omap_i2c_dev *i2c_dev,
> + int reg, u16 val)
> +{
> + __raw_writew(val, i2c_dev->base + reg);
> +}
> +
> +static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg)
> +{
> + return __raw_readw(i2c_dev->base + reg);
> +}
> +
> +static int omap_i2c_get_clocks(struct omap_i2c_dev *dev)
> +{
> + if (cpu_is_omap16xx() || cpu_is_omap24xx()) {
> + dev->iclk = clk_get(dev->dev, "i2c_ick");
> + if (IS_ERR(dev->iclk))
> + return -ENODEV;
> + }
> +
> + dev->fclk = clk_get(dev->dev, "i2c_fck");
> + if (IS_ERR(dev->fclk)) {
> + if (dev->iclk != NULL)
> + clk_put(dev->iclk);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static void omap_i2c_put_clocks(struct omap_i2c_dev *dev)
> +{
> + clk_put(dev->fclk);
> + dev->fclk = NULL;
> + if (dev->iclk != NULL) {
> + clk_put(dev->iclk);
> + dev->iclk = NULL;
> + }
> +}

There is a minor inconsistency here, omap_i2c_put_clocks sets the
pointers to NULL, but the error paths of omap_i2c_get_clocks don't?

> +
> +static void omap_i2c_enable_clocks(struct omap_i2c_dev *dev)
> +{
> + if (dev->iclk != NULL)
> + clk_enable(dev->iclk);
> + clk_enable(dev->fclk);
> +}
> +
> +static void omap_i2c_disable_clocks(struct omap_i2c_dev *dev)
> +{
> + if (dev->iclk != NULL)
> + clk_disable(dev->iclk);
> + clk_disable(dev->fclk);
> +}
> +
> +static void omap_i2c_reset(struct omap_i2c_dev *dev)

This function is misnamed, it seems to fully initialize the device, not
just reset it.

> +{
> + u16 psc;
> + unsigned long fclk_rate;
> +
> + if (!dev->rev1) {

Would be nice to explain why/how this revision is different in a
comment.

> + omap_i2c_write_reg(dev, OMAP_I2C_SYSC_REG, OMAP_I2C_SYSC_SRST);
> + /* For some reason we need to set the EN bit before the
> + * reset done bit gets set. */
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
> + while (!(omap_i2c_read_reg(dev, OMAP_I2C_SYSS_REG) & 0x01));

No way. This is calling for a deadlock sooner or later. You can't just
expect that the hardware will ever set that bit you are waiting for, so
you need some timeout mechanism.

Also, shouldn't this 0x01 actually be OMAP_I2C_SYSS_RDONE?

> + }
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
> +
> + if (cpu_class_is_omap1()) {
> + struct clk *armxor_ck;
> + unsigned long armxor_rate;
> +
> + armxor_ck = clk_get(NULL, "armxor_ck");
> + if (IS_ERR(armxor_ck)) {
> + printk(KERN_WARNING "i2c: Could not get armxor_ck\n");

Please use dev_warn() instead.

> + armxor_rate = 12000000;
> + } else {
> + armxor_rate = clk_get_rate(armxor_ck);
> + clk_put(armxor_ck);
> + }
> +
> + if (armxor_rate > 16000000)
> + psc = (armxor_rate + 8000000) / 12000000;
> + else
> + psc = 0;

Can you please explain this formula?

> +
> + fclk_rate = armxor_rate;

I fail to see why you have been introducing this armxor_rate local
variable, instead of setting fclk_rate directly.

> + } else if (cpu_class_is_omap2()) {
> + fclk_rate = 12000000;
> + psc = 0;
> + }

Else? fclk_rate and psc are undefined, and the following code will do
random writes.

You really shouldn't ignore compiler warnings, you know? ;)

Given that these seem to be the defaults in several cases, it might
make sense to initialize them to 1200000 and 0, respectively, and kill
some code.

> +
> + /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
> + omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc);
> +
> + /* Program desired operating rate */
> + fclk_rate /= (psc + 1) * 1000;
> + if (psc > 2)
> + psc = 2;
> +
> + omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG,
> + fclk_rate / (clock * 2) - 7 + psc);
> + omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG,
> + fclk_rate / (clock * 2) - 7 + psc);
> +
> + /* Set Own Address: */
> + omap_i2c_write_reg(dev, OMAP_I2C_OA_REG, dev->own_address);
> +
> + /* Take the I2C module out of reset: */
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
> +
> + /* Enable interrupts */
> + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG,
> + (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY |
> + OMAP_I2C_IE_ARDY | OMAP_I2C_IE_NACK |
> + OMAP_I2C_IE_AL));
> +}
> +
> +/*
> + * Waiting on Bus Busy
> + */
> +static int omap_i2c_wait_for_bb(struct omap_i2c_dev *dev)
> +{
> + unsigned long timeout;
> +
> + timeout = jiffies + OMAP_I2C_TIMEOUT;
> + while (omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG) & OMAP_I2C_STAT_BB) {
> + if (time_after(jiffies, timeout)) {
> + dev_warn(dev->dev, "timeout waiting for bus ready\n");
> + return -ETIMEDOUT;
> + }
> + msleep(1);
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * Low level master read/write transaction.
> + */
> +static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
> + struct i2c_msg *msg, int stop)
> +{
> + struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
> + int r;
> + u16 w;
> + u8 zero_byte = 0;
> +
> + dev_dbg(dev->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n",
> + msg->addr, msg->len, msg->flags, stop);
> +
> + omap_i2c_write_reg(dev, OMAP_I2C_SA_REG, msg->addr);
> +
> + /* Sigh, seems we can't do zero length transactions. Thus, we
> + * can't probe for devices w/o actually sending/receiving at least
> + * a single byte. So we'll set count to 1 for the zero length
> + * transaction case and hope we don't cause grief for some
> + * arbitrary device due to random byte write/read during
> + * probes.
> + */

That is, you lie on your capabilities. This is no good. You should not
advertise something the device can't actually do, and you should fail
if still requested to do it. You just can't write a byte to a chip when
you were asked to write none, sorry.

> + /* REVISIT: Could the STB bit of I2C_CON be used with probing? */
> + if (msg->len == 0) {
> + dev->buf = &zero_byte;
> + dev->buf_len = 1;
> + } else {
> + dev->buf = msg->buf;
> + dev->buf_len = msg->len;
> + }
> + omap_i2c_write_reg(dev, OMAP_I2C_CNT_REG, dev->buf_len);
> +
> + init_completion(&dev->cmd_complete);
> + dev->cmd_err = 0;
> +
> + w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT;
> + if (msg->flags & I2C_M_TEN)
> + w |= OMAP_I2C_CON_XA;
> + if (!(msg->flags & I2C_M_RD))
> + w |= OMAP_I2C_CON_TRX;
> + if (stop)
> + w |= OMAP_I2C_CON_STP;
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, w);
> +
> + r = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
> + OMAP_I2C_TIMEOUT);
> + dev->buf_len = 0;
> + if (r < 0)
> + return r;
> + if (r == 0) {
> + dev_err(dev->dev, "controller timed out\n");
> + omap_i2c_reset(dev);
> + return -ETIMEDOUT;
> + }
> +
> + if (likely(!dev->cmd_err))
> + return 0;
> +
> + /* We have an error */
> + if (dev->cmd_err & OMAP_I2C_STAT_NACK) {
> + if (msg->flags & I2C_M_IGNORE_NAK)
> + return 0;

Couldn't you have other error bits set as well? I2C_M_IGNORE_NAK means
you can ignore OMAP_I2C_STAT_NACK, not other errors.

> + if (stop) {
> + u16 w;

You already have an u16 w available, why define a new one?

> +
> + w = omap_i2c_read_reg(dev, OMAP_I2C_CON_REG);
> + w |= OMAP_I2C_CON_STP;
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, w);
> + }
> + return -EREMOTEIO;
> + }
> + if (dev->cmd_err & (OMAP_I2C_STAT_AL | OMAP_I2C_STAT_ROVR |
> + OMAP_I2C_STAT_XUDF))
> + omap_i2c_reset(dev);
> + return -EIO;
> +}
> +
> +
> +/*
> + * Prepare controller for a transaction and call omap_i2c_xfer_msg
> + * to do the work during IRQ processing.
> + */
> +static int
> +omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
> +{
> + struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
> + int i;
> + int r = 0;

Needless initialization.

> +
> + if (num < 1 || num > MAX_MESSAGES)
> + return -EINVAL;

This check doesn't appear to be necessary.

> +
> + /* Check for valid parameters in messages */
> + for (i = 0; i < num; i++)
> + if (msgs[i].buf == NULL)
> + return -EINVAL;

Nor does this one - no other i2c bus drivers checks this. If we wanted
to check this, we would do it at the i2c-core level.

> +
> + omap_i2c_enable_clocks(dev);
> +
> + /* REVISIT: initialize and use adap->retries */
> + if ((r = omap_i2c_wait_for_bb(dev)) < 0)
> + goto out;
> +
> + for (i = 0; i < num; i++) {
> + dev_dbg(dev->dev, "msg: %d, addr: 0x%04x, len: %d, flags: 0x%x\n",
> + i, msgs[i].addr, msgs[i].len, msgs[i].flags);

You have the same debug message at the beginning of omap_i2c_xfer_msg,
this is redundant.

> + r = omap_i2c_xfer_msg(adap, &msgs[i], (i == (num - 1)));
> + if (r != 0)
> + break;
> + }
> +
> + if (r == 0)
> + r = num;
> +out:
> + omap_i2c_disable_clocks(dev);
> + return r;
> +}
> +
> +static u32
> +omap_i2c_func(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}

As said above, you shouldn't advertise I2C_FUNC_SMBUS_EMUL, as you
can't do I2C_FUNC_SMBUS_QUICK.

> +
> +static inline void
> +omap_i2c_complete_cmd(struct omap_i2c_dev *dev, u16 err)
> +{
> + dev->cmd_err |= err;
> + complete(&dev->cmd_complete);
> +}
> +
> +static inline void
> +omap_i2c_ack_stat(struct omap_i2c_dev *dev, u16 stat)
> +{
> + omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat);
> +}
> +
> +static irqreturn_t
> +omap_i2c_rev1_isr(int this_irq, void *dev_id, struct pt_regs *regs)
> +{
> + struct omap_i2c_dev *dev = dev_id;
> + u16 iv, w;
> +
> + iv = omap_i2c_read_reg(dev, OMAP_I2C_IV_REG);
> + switch (iv) {
> + case 0x00: /* None */
> + break;
> + case 0x01: /* Arbitration lost */
> + dev_err(dev->dev, "Arbitration lost\n");
> + omap_i2c_complete_cmd(dev, OMAP_I2C_STAT_AL);
> + break;
> + case 0x02: /* No acknowledgement */
> + omap_i2c_complete_cmd(dev, OMAP_I2C_STAT_NACK);
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_STP);
> + break;
> + case 0x03: /* Register access ready */
> + omap_i2c_complete_cmd(dev, 0);
> + break;
> + case 0x04: /* Receive data ready */
> + if (dev->buf_len) {
> + w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
> + *dev->buf++ = w;

Shouldn't this be w & 0xff? (I agree it doesn't change anything in
practice, but...)

> + dev->buf_len--;
> + if (dev->buf_len) {
> + *dev->buf++ = w >> 8;
> + dev->buf_len--;
> + }
> + } else
> + dev_err(dev->dev, "RRDY IRQ while no data requested\n");
> + break;
> + case 0x05: /* Transmit data ready */
> + if (dev->buf_len) {
> + w = *dev->buf++;
> + dev->buf_len--;
> + if (dev->buf_len) {
> + w |= *dev->buf++ << 8;
> + dev->buf_len--;
> + }
> + omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
> + } else
> + dev_err(dev->dev, "XRDY IRQ while no data to send\n");
> + break;
> + default:
> + return IRQ_NONE;
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t
> +omap_i2c_isr(int this_irq, void *dev_id, struct pt_regs *regs)
> +{
> + struct omap_i2c_dev *dev = dev_id;
> + u16 bits;
> + u16 stat, w;
> + int count = 0;
> +
> + bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
> + while ((stat = (omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG))) & bits) {
> + dev_dbg(dev->dev, "IRQ (ISR = 0x%04x)\n", stat);
> + if (count++ == 100) {
> + dev_warn(dev->dev, "Too much work in one IRQ\n");
> + break;
> + }
> +
> + omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat);
> +
> + if (stat & OMAP_I2C_STAT_ARDY) {
> + omap_i2c_complete_cmd(dev, 0);
> + continue;
> + }
> + if (stat & OMAP_I2C_STAT_RRDY) {
> + w = omap_i2c_read_reg(dev, OMAP_I2C_DATA_REG);
> + if (dev->buf_len) {
> + *dev->buf++ = w;

I'd add & 0xff here as well.

> + dev->buf_len--;
> + if (dev->buf_len) {
> + *dev->buf++ = w >> 8;
> + dev->buf_len--;
> + }
> + } else
> + dev_err(dev->dev, "RRDY IRQ while no data requested\n");
> + omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RRDY);
> + continue;
> + }
> + if (stat & OMAP_I2C_STAT_XRDY) {
> + int bail_out = 0;
> +
> + w = 0;
> + if (dev->buf_len) {
> + w = *dev->buf++;
> + dev->buf_len--;
> + if (dev->buf_len) {
> + w |= *dev->buf++ << 8;
> + dev->buf_len--;
> + }
> + } else
> + dev_err(dev->dev, "XRDY IRQ while no data to send\n");
> +#if 0
> + if (!(stat & OMAP_I2C_STAT_BB)) {
> + dev_warn(dev->dev, "XRDY while bus not busy\n");
> + bail_out = 1;
> + }
> +#endif

Why is this if'd out? If it's not needed, please drop.

> + omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
> + omap_i2c_ack_stat(dev, OMAP_I2C_STAT_XRDY);
> + if (bail_out)
> + omap_i2c_complete_cmd(dev, 1 << 15);

Where does this 1 << 15 come from?

> + continue;
> + }
> + if (stat & OMAP_I2C_STAT_ROVR) {
> + dev_err(dev->dev, "Receive overrun\n");
> + dev->cmd_err |= OMAP_I2C_STAT_ROVR;
> + }
> + if (stat & OMAP_I2C_STAT_XUDF) {
> + dev_err(dev->dev, "Transmit overflow\n");
> + dev->cmd_err |= OMAP_I2C_STAT_XUDF;
> + }
> + if (stat & OMAP_I2C_STAT_NACK) {
> + omap_i2c_complete_cmd(dev, OMAP_I2C_STAT_NACK);
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_STP);
> + }
> + if (stat & OMAP_I2C_STAT_AL) {
> + dev_err(dev->dev, "Arbitration lost\n");
> + omap_i2c_complete_cmd(dev, OMAP_I2C_STAT_AL);
> + }
> + }
> +
> + return count ? IRQ_HANDLED : IRQ_NONE;
> +}

Several lines larger than 80 columns in the above function, please fix.

> +
> +static struct i2c_algorithm omap_i2c_algo = {
> + .master_xfer = omap_i2c_xfer,
> + .functionality = omap_i2c_func,
> +};
> +
> +static int
> +omap_i2c_probe(struct platform_device *pdev)
> +{
> + struct omap_i2c_dev *dev;
> + struct i2c_adapter *adap;
> + struct resource *mem, *irq;
> + int r;
> +
> + /* NOTE: driver uses the static register mapping */
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!mem) {
> + dev_err(&pdev->dev, "no mem resource?\n");
> + return -ENODEV;
> + }
> + irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> + if (!irq) {
> + dev_err(&pdev->dev, "no irq resource?\n");
> + return -ENODEV;
> + }
> +
> + r = (int) request_mem_region(mem->start, (mem->end - mem->start) + 1,
> + driver_name);

Ugly cast, you can do without it.

> + if (!r) {
> + dev_err(&pdev->dev, "I2C region already claimed\n");
> + return -EBUSY;
> + }
> +
> + if (clock > 200)
> + clock = 400; /* Fast mode */
> + else
> + clock = 100; /* Standard mode */
> +
> + dev = kzalloc(sizeof(struct omap_i2c_dev), GFP_KERNEL);
> + if (!dev) {
> + r = -ENOMEM;
> + goto do_release_region;
> + }
> +
> + /* FIXME: Get own address from platform_data */
> + if (own >= 1 && own < 0x7f)
> + dev->own_address = own;

Your range is slightly too wide actually. You should only accept
addresses from 0x03 to 0x77. Others are reserved for future use or for
the 10-bit addressing.

Anyway, given that Linux doesn't support this at the moment, I wonder
why you bother setting it.

> + else
> + own = DEFAULT_OWN;
> +
> + dev->dev = &pdev->dev;
> + dev->irq = irq->start;
> + dev->base = (void __iomem *) IO_ADDRESS(mem->start);
> + platform_set_drvdata(pdev, dev);
> +
> + if ((r = omap_i2c_get_clocks(dev)) != 0)
> + goto do_free_mem;
> +
> + omap_i2c_enable_clocks(dev);
> +
> + if (cpu_is_omap15xx())
> + dev->rev1 = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) < 0x20;
> +
> + /* reset ASAP, clearing any IRQs */
> + omap_i2c_reset(dev);
> +
> + if (cpu_is_omap15xx())
> + r = request_irq(dev->irq, dev->rev1 ? omap_i2c_rev1_isr : omap_i2c_isr,

Line too long.

> + 0, driver_name, dev);
> + else
> + r = request_irq(dev->irq, omap_i2c_isr, 0, driver_name, dev);

This could be simplified. The test on cpu_is_omap15xx() is not needed,
dev->rev1 can only be set if it is true. So the "if" part works in all
cases.

> +
> + if (r) {
> + dev_err(dev->dev, "failure requesting irq %i\n", dev->irq);
> + goto do_unuse_clocks;
> + }
> + r = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) & 0xff;
> + dev_info(dev->dev, "bus %d rev%d.%d at %d kHz\n",
> + pdev->id - 1, r >> 4, r & 0xf, clock);

This "- 1" is error prone IMHO.

> +
> + adap = &dev->adapter;
> + i2c_set_adapdata(adap, dev);
> + adap->owner = THIS_MODULE;
> + adap->class = I2C_CLASS_HWMON;
> + strncpy(adap->name, "OMAP I2C adapter", sizeof(adap->name));
> + adap->algo = &omap_i2c_algo;
> + adap->dev.parent = &pdev->dev;
> +
> + /* i2c device drivers may be active on return from add_adapter() */
> + r = i2c_add_adapter(adap);
> + if (r) {
> + dev_err(dev->dev, "failure adding adapter\n");
> + goto do_free_irq;
> + }
> +
> + omap_i2c_disable_clocks(dev);
> +
> + return 0;
> +
> +do_free_irq:
> + free_irq(dev->irq, dev);
> +do_unuse_clocks:
> + omap_i2c_disable_clocks(dev);
> + omap_i2c_put_clocks(dev);
> +do_free_mem:

Missing platform_set_drvdata(pdev, NULL).

> + kfree(dev);
> +do_release_region:
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
> + release_mem_region(mem->start, (mem->end - mem->start) + 1);
> +
> + return r;
> +}

These do_ prefixes on your labels are bad looking (probably a matter of
taste...) What about err_ or exit_ instead?

> +
> +static int
> +omap_i2c_remove(struct platform_device *pdev)
> +{
> + struct omap_i2c_dev *dev = platform_get_drvdata(pdev);
> + struct resource *mem;
> +

I would suggest platform_set_drvdata(pdev, NULL) before anything else,
else you leave a dangling pointed behind you.

> + free_irq(dev->irq, dev);
> + i2c_del_adapter(&dev->adapter);
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
> + omap_i2c_put_clocks(dev);
> + kfree(dev);
> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + release_mem_region(mem->start, (mem->end - mem->start) + 1);
> + return 0;
> +}
> +
> +static struct platform_driver omap_i2c_driver = {
> + .probe = omap_i2c_probe,
> + .remove = omap_i2c_remove,
> + .driver = {

Space before tab (after "driver").

> + .name = (char *)driver_name,

This case shouldn't be necessary?

Also, missing .owner = THIS_MODULE.

> + },
> +};
> +
> +/* I2C may be needed to bring up other drivers */
> +static int __init
> +omap_i2c_init_driver(void)
> +{
> + return platform_driver_register(&omap_i2c_driver);
> +}
> +subsys_initcall(omap_i2c_init_driver);
> +
> +static void __exit omap_i2c_exit_driver(void)
> +{
> + platform_driver_unregister(&omap_i2c_driver);
> +}
> +module_exit(omap_i2c_exit_driver);
> +
> +MODULE_AUTHOR("MontaVista Software, Inc. (and others)");
> +MODULE_DESCRIPTION("TI OMAP I2C bus adapter");
> +MODULE_LICENSE("GPL");

Here you are. Please address theses issues, then you can resubmit you
driver.

--
Jean Delvare
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/