ASUS A8V Deluxe, x86_64

From: Fortier,Vincent [Montreal]
Date: Mon May 15 2006 - 08:07:28 EST


Sadly I needed to change my ASUS CUV4X-D (dual 1ghz) about 9 months
ago... It was running slowly but smoothly.

Now I'm having an ASUS A8V Deluxe.... and sadly a lot of problems:

- My SATA Controller make my Linux crash when connecting a Plextor 716SA
CD-DVD-R (http://bugzilla.kernel.org/show_bug.cgi?id=5533)
- My onboard network card either stops responding (using sk98lin) or
make my PC freeze (using skge)
- My USB mouse goes crazy from times to times (at least every few hours)
until I remove ehci_hcd and uhci_hcd and readd uhci_hcd
- My PC partially wakes up and freeze after a few hours of no usage

Although most of my job is doing Linux system administration and even if
I try to keep myself has informed has I can I still can't get my Linux
working properly (I keep on reading lwn and I subscribed to lkml
recently). I just can't keep my PC running smoothly...

Where should I start from? Is this a good place to ask for help?

Any help appreciated!

- vin


Here are my devices and I also attached my dmesg... just in case:
00:00.0 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge
[K8T800/K8T890 South] 00:07.0 FireWire (IEEE 1394): VIA Technologies,
Inc. IEEE 1394 Host Controller (rev 80) 00:0a.0 Ethernet controller:
Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev
13) 00:0d.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet
Pro 100] (rev 01) 00:0f.0 RAID bus controller: VIA Technologies, Inc.
VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:10.0
USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) 00:11.0
ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
Controller (rev 80) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control 01:00.0 VGA compatible controller: nVidia
Corporation NV40 [GeForce 6800] (rev a1)


Bootdata ok (command line is ro root=LABEL=/FC5_x86_64 vga=0x305)
Linux version 2.6.17-rc4-git1-x86_64-007 (root@gustav) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #1 SMP Sat May 13 10:07:00 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data)
BIOS-e820: 000000007ffc0000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa7c0
ACPI: XSDT (v001 A M I OEMXSDT 0x12000530 MSFT 0x00000097) @ 0x000000007ffb0100
ACPI: FADT (v003 A M I OEMFACP 0x12000530 MSFT 0x00000097) @ 0x000000007ffb0290
ACPI: MADT (v001 A M I OEMAPIC 0x12000530 MSFT 0x00000097) @ 0x000000007ffb0390
ACPI: OEMB (v001 A M I OEMBIOS 0x12000530 MSFT 0x00000097) @ 0x000000007ffc0040
ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007ffb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000007ffb0000
On node 0 totalpages: 516935
DMA zone: 3933 pages, LIFO batch:0
DMA32 zone: 513002 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7f780000)
Checking aperture...
CPU 0: aperture @ e8000000 size 64 MB
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists
Kernel command line: ro root=LABEL=/FC5_x86_64 vga=0x305
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2202.874 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2043692k/2096832k available (2167k kernel code, 52752k reserved, 953k data, 196k init)
Calibrating delay using timer specific routine.. 4411.28 BogoMIPS (lpj=8822578)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0(2) -> Node 0 -> Core 0
Using local APIC timer interrupts.
result 12516350
Detected 12.516 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4405.95 BogoMIPS (lpj=8811919)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 11 cycles, maxerr 516 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=210
checking if image is initramfs... it is
Freeing initrd memory: 1124k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Quirk-MSI-K8T Soundcard On
PCI: Unexpected Value in PCI-Register: no Change!
PCI: enabled onboard AC97/MC97 devices
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xe8000000
PCI-DMA: Disabling IOMMU.
pnp: 00:07: ioport range 0x680-0x6ff has been reserved
pnp: 00:07: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f9f00000-fbffffff
PREFETCH window: f0000000-f8ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1147671085.956:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20000080000, using 1536k, total 131072k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
isa bounce pool size: 16 pages
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 16
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: YAMAHA CRW3200E, ATAPI CD/DVD-ROM drive
hdb: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.2)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc (1250 mV)
powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xe, vid 0x8
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI wakeup devices:
PCI0 PS2K UAR2 UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Write protecting the kernel read-only data: 428k
SCSI subsystem initialized
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 16
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 16
ata2: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: SATA link down (SStatus 0)
scsi1 : sata_via
Vendor: ATA Model: Maxtor 6B250S0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 >
sd 0:0:0:0: Attached scsi disk sda
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1147671099.437:2): selinux=0 auid=4294967295
ieee1394: Initialized config rom entry `ip1394'
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 17
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[f9800000-f98007ff] Max Packet=[2048] IR/IT contexts=[4/8]
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 18
skge 1.5 addr 0xf9a00000 irq 18 chip Yukon-Lite rev 9
skge eth0: addr 00:13:d4:11:03:a9
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 19
e100: eth1: e100_probe: addr 0xeff00000, irq 19, MAC addr 00:90:27:15:CD:B6
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 20
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 20, io mem 0xf9e00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 20, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 20, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 20, io base 0x0000e000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 20, io base 0x0000e400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-8756 Wed Mar 29 15:12:41 PST 2006
ieee1394: Node added: ID:BUS[0-00:1023] GUID[0010100500001b74]
ieee1394: Host added: ID:BUS[0-01:1023] GUID[0011d800003a31cd]
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
scsi2 : SBP-2 IEEE-1394
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
Linux video capture interface: v1.00
pwc Philips webcam module version 9.0.2-unofficial loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usb 3-2: new low speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:10.1-2
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048]
Vendor: PI-036 Model: 1394/USB20 Drive Rev: 4.65
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
sdb: Mode Sense: 86 0b 00 02
sdb: missing header in MODE_SENSE response
SCSI device sdb: drive cache: write back
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
sdb: Mode Sense: 86 0b 00 02
sdb: missing header in MODE_SENSE response
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 >
sd 2:0:0:0: Attached scsi disk sdb
sd 2:0:0:0: Attached scsi generic sg1 type 0
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:11.5 to 64
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1204
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
pwc Logitech QuickCam 4000 Pro USB webcam detected.
pwc Registered as /dev/video0.
usbcore: registered new driver Philips webcam
usbcore: registered new driver snd-usb-audio
Non-volatile memory driver v1.2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
lp: driver loaded but no devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on sda7, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1959888k swap on /dev/sda5. Priority:-1 extents:1 across:1959888k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
w83627hf 9191-0290: Reading VID from GPIO5
ppdev: user-space parallel port driver
ppdev0: claim the port first
ppdev1: claim the port first
ppdev2: claim the port first
ppdev3: claim the port first
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-2: SMBus Quick command not supported, can't probe for chips
i2c_adapter i2c-3: SMBus Quick command not supported, can't probe for chips
pwc Failed to set LED on/off time.
pwc type = 740
pwc type = 740
pwc set_video_mode(176x144 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
pwc Dumping frame 6.
pwc Dumping frame 7.
pwc Dumping frame 8.
pwc Dumping frame 9.
pwc Dumping frame 10.
pwc Dumping frame 11.
pwc Dumping frame 12.
pwc Dumping frame 13.
pwc Dumping frame 14.
pwc Dumping frame 15.
pwc Dumping frame 16.
pwc type = 740
pwc type = 740
pwc set_video_mode(160x120 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
pwc Dumping frame 6.
pwc Dumping frame 7.
ehci_hcd 0000:00:10.4: remove, state 1
usb usb1: USB disconnect, address 1
ehci_hcd 0000:00:10.4: USB bus 1 deregistered
uhci_hcd 0000:00:10.3: remove, state 1
usb usb5: USB disconnect, address 1
uhci_hcd 0000:00:10.3: USB bus 5 deregistered
uhci_hcd 0000:00:10.2: remove, state 1
usb usb4: USB disconnect, address 1
uhci_hcd 0000:00:10.2: USB bus 4 deregistered
uhci_hcd 0000:00:10.1: remove, state 1
usb usb3: USB disconnect, address 1
usb 3-1: USB disconnect, address 2
usb 3-2: USB disconnect, address 3
uhci_hcd 0000:00:10.1: USB bus 3 deregistered
uhci_hcd 0000:00:10.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
drivers/usb/class/usblp.c: usblp0: removed
uhci_hcd 0000:00:10.0: USB bus 2 deregistered
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 20, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 20, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 20, io base 0x0000e000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 20
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 20, io base 0x0000e400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1204
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
pwc Logitech QuickCam 4000 Pro USB webcam detected.
pwc Registered as /dev/video0.
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:10.1-2