Re: 2.6.16-rc1-mm2 pata driver confusion

From: Ed Sweetman
Date: Tue Jan 24 2006 - 20:56:48 EST


Randy.Dunlap wrote:

On Tue, 24 Jan 2006, Ed Sweetman wrote:



Randy.Dunlap wrote:



On Tue, 24 Jan 2006, Ed Sweetman wrote:



Alan Cox wrote:



On Maw, 2006-01-24 at 01:43 -0500, Ed Sweetman wrote:




problem. The problem is that there appears to be two nvidia/amd ata
drivers and I'm unsure which I should try using, if i compile both in,
which get loaded first (i assume scsi is second to ide) and if i want my
pata disks loaded under the new libata drivers, will my cdrom work under
them too, or do i still need some sort of regular ide drivers loaded
just for cdrom (to use native ata mode for recording access).




The goal of the drivers/scsi/pata_* drivers is to replace drivers/ide in
its entirity with code using the newer and cleaner libata logic. There
is still much to do but my SIL680, SiS, Intel MPIIX, AMD and VIA boxes
are using libata and the additional patch patches still queued




1. Atapi is most definitely not supported by libata, right now.




It works in the -mm tree.




Intriguing, when I had no ide chipset compiled in kernel, only libata
drivers, I got no mention at all about my dvd writer. I even had the
scsi cd driver installed and generic devices, still nothing seemed to
initialize the dvd drive. It detected the second pata bus but no
devices attached to it.

this is using the kernel mentioned in the subject header.
2.6.16-rc1-mm2. using the amd/nvidia drivers for pata and sata.

Is there anything i can do to give more info to the list to figure out
why my atapi writer is being ignored by pata even when there are no ide
drivers loaded?



Currently you need to use libata.atapi_enabled=1
(assuming that libata is in the kernel image, not a loadable module).

I just built/tested this also, working for me as well.
(hard drives, not ATAPI)




I assume libata.atapi_enabled=1 is a boot arg, not some structure member
in the source for the pata driver that i need to set to 1, correct?



Yes, it's a kernel boot option if libata is in the kernel image.
If libata is a loadable module, just use something like
modprobe libata atapi_enabled=1



And you just built and tested it, how did you test if the atapi argument
worked when you then say "not ATAPI" as something you tested?



Sorry, I mean that I built and booted a kernel with libata/PATA
hard drive (vs. legacy drivers/ide/ PATA support). I have not
tested ATAPI at all and didn't mean to imply that I had.

I reported on libata.atapi_enabled=1 based on documentation
and other emails that I have read.



In any case, i'll try out libata.atapi_enabled=1 and see if it detects
the dvd drive.



HTH. Please continue to post any questions or problems.



I Rebooted several times, both setting the option in the kernel boot args and editing the source to have it set by default. No atapi devices are found/mentioned or even described as not found in dmesg/bootup. So apparently, on my chipset, the amd/nvidia pata driver is not detecting atapi devices.

0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
0000:00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
0000:00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)

0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])
Subsystem: Unknown device f043:815a
Flags: bus master, 66MHz, fast devsel, latency 0
I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2



the atapi device in question is a plextor px-712A, it's the only device on the secondary channel.



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/