Re: bad pmd filemap.c, oops; 2.4.30 and 2.4.32

[Chris Stromsoe]

I couldn't get the machine to come up with 2.4.32, 2.4.30, or 2.4.27.  It 
was hanging and then throwing the SCSI errors below.  The machine did come 
up with a vanilla 2.6.14.4 and appears to be working fine.  I'm going to 
leave it up over the weekend and see if it oopses.  If it would help, I 
can mail out the .config for the 2.4.32 and 2.6.14.4 builds, or provide 
other information of interest.

-Chris

On Fri, 30 Dec 2005, Chris Stromsoe wrote:

> I'm starting to suspect bad hardware.  Booting is now hanging (with 
> 2.4.27, 2.4.30 and 2.4.32) after scsi drivers load:
>
> .....
>
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a National Semiconductor PC87306
> Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: attached ide-cdrom driver.
> hda: ATAPI 24X CD-ROM drive, 128kB Cache
> Uniform CD-ROM driver Revision: 3.12
> SCSI subsystem driver Revision: 1.00
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>        <Adaptec 3960D Ultra160 SCSI adapter>
>        aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
>
> scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>        <Adaptec 3960D Ultra160 SCSI adapter>
>        aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
>
> scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>        <Adaptec aic7899 Ultra160 SCSI adapter>
>        aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
>
> blk: queue f7e46018, I/O limit 4095Mb (mask 0xffffffff)
>
>
> If I wait several minutes (around 10 or 15 minutes), I get:
>
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x12 0x0 0x0 0x0 0xff 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue a TARGET RESET message
> CDB: 0x12 0x0 0x0 0x0 0xff 0x0
> scsi0:0:0:0: Is not an active device
> aic7xxx_dev_reset returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi0:0:0:0: Attempting to queue an ABORT message
> CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 0x2002
> scsi: device set offline - not ready or command retry failed after bus reset: 
> host 0 channel 0 id 0 lun 0
>
>
> The messages repeated for all 15 targets on scsi0.  It's looking like it will 
> repeat for scsi1 as well.
>
> How likely is it that a failing scsi controller contribute to the other 
> problems I was seeing?
>
>
> -Chris
>
> On Fri, 30 Dec 2005, Chris Stromsoe wrote:
>
> > I oopsed again last night with an identical EIP and Call Trace to the oops 
> > from the 28th.  The new oops is below, the prior below that.  I'm going to 
> > reboot the machine into UP and see if that helps.
> >
> > -Chris
> >
> > Unable to handle kernel paging request at virtual address c211ce80
> > c0259bb3
> > *pde = 020001e3
> > Oops: 0002
> > CPU:    2
> > EIP:    0010:[alloc_skb+275/480]    Not tainted
> > EFLAGS: 00010282
> > eax: c211ce80   ebx: f5303680   ecx: f7eeb780   edx: 00000680
> > esi: 000001f0   edi: 00000000   ebp: d348ddf0   esp: d348dddc
> > ds: 0018   es: 0018   ss: 0018
> > Process innfeed (pid: 25080, stackpage=d348d000)
> > Stack: 000006bc 000001f0 ebabc980 eb0e64d8 eb0e6400 d348de68 c027b50b 
> > 00000680
> >       000001f0 000005a8 00000000 d348de54 00000000 00000000 00000001 
> > 00000000
> >       012815b5 00000000 00000000 d7a160a0 d348c000 636686ac 000c3dec 
> > 000087c0
> > Call Trace:    [tcp_sendmsg+2619/4512] [inet_sendmsg+65/80] 
> > [sock_sendmsg+102/176] [sock_readv_writev+116/176] [sock_writev+79/96]
> > Code: c7 00 01 00 00 00 8b 83 8c 00 00 00 c7 40 04 00 00 00 00 8b
> > Using defaults from ksymoops -t elf32-i386 -a i386
> >
> >
> > > > eax; c211ce80 <_end+1d3b380/38650560>
> > > > ebx; f5303680 <_end+34f21b80/38650560>
> > > > ecx; f7eeb780 <_end+37b09c80/38650560>
> > > > ebp; d348ddf0 <_end+130ac2f0/38650560>
> > > > esp; d348dddc <_end+130ac2dc/38650560>
> >
> > Code;  00000000 Before first symbol
> > 00000000 <_EIP>:
> > Code;  00000000 Before first symbol
> >   0:   c7 00 01 00 00 00         movl   $0x1,(%eax)
> > Code;  00000006 Before first symbol
> >   6:   8b 83 8c 00 00 00         mov    0x8c(%ebx),%eax
> > Code;  0000000c Before first symbol
> >   c:   c7 40 04 00 00 00 00      movl   $0x0,0x4(%eax)
> > Code;  00000013 Before first symbol
> >  13:   8b 00                     mov    (%eax),%eax
> >
> >
> > On Wed, 28 Dec 2005, Chris Stromsoe wrote:
> >
> > > Unable to handle kernel paging request at virtual address c22eee80
> > > c0259bb3
> > > *pde = 020001e3
> > > Oops: 0002
> > > CPU:    2
> > > EIP:    0010:[alloc_skb+275/480]    Not tainted
> > > EFLAGS: 00010282
> > > eax: c22eee80   ebx: ccbdb480   ecx: 000006bc   edx: 00000680
> > > esi: 000001f0   edi: 00000000   ebp: f663bdf0   esp: f663bddc
> > > ds: 0018   es: 0018   ss: 0018
> > > Process innfeed (pid: 526, stackpage=f663b000)
> > > Stack: 000006bc 000001f0 ccbdb080 00000000 f7185800 f663be68 c027b50b 
> > > 00000680
> > >        000001f0 000005a8 00000000 f663be54 00000000 00000287 d84bec38 
> > > d84bec34
> > >        d84bec54 f663a000 00000000 d5fbd8a0 f663a000 586d4438 0002c774 
> > > 000005a8
> > > Call Trace:    [tcp_sendmsg+2619/4512] [inet_sendmsg+65/80] 
> > > [sock_sendmsg+102/176] [sock_readv_writev+116/176] [sock_writev+79/96]
> > > Code: c7 00 01 00 00 00 8b 83 8c 00 00 00 c7 40 04 00 00 00 00 8b Using 
> > > defaults from ksymoops -t elf32-i386 -a i386
> > >
> > > > > eax; c22eee80 <_end+1f0d380/38650560>
> > > > > ebx; ccbdb480 <_end+c7f9980/38650560>
> > > > > ebp; f663bdf0 <_end+3625a2f0/38650560>
> > > > > esp; f663bddc <_end+3625a2dc/38650560>
> > >
> > > Code;  00000000 Before first symbol
> > > 00000000 <_EIP>:
> > > Code;  00000000 Before first symbol
> > >   0:   c7 00 01 00 00 00         movl   $0x1,(%eax)
> > > Code;  00000006 Before first symbol
> > >   6:   8b 83 8c 00 00 00         mov    0x8c(%ebx),%eax
> > > Code;  0000000c Before first symbol
> > >   c:   c7 40 04 00 00 00 00      movl   $0x0,0x4(%eax)
> > > Code;  00000013 Before first symbol
> > >  13:   8b 00                     mov    (%eax),%eax
> > > -
> > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > > Please read the FAQ at  http://www.tux.org/lkml/
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at  http://www.tux.org/lkml/
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/