Re: 2.6.11-rc5

From: Mws
Date: Fri Feb 25 2005 - 08:34:23 EST

hi,

i also have problems with 2.6.11-rc5 and radeon:

i am using a ATI Radeon X600 PciExpress.

a) now the console framebuffer seems to bee working, thx benjamin :)
b) when bootup seq ist completed and i want to start X (xorg-x11) with ati-drivers
x is freezing - not your problem, but the console is not correctly restored :/ the only way
out is to reset the machine :/
2.6.11-rc3 was running fine in this case

i have attached my lspci -vv & lspci -tv output and following a small seq of the dmesg output
when initializing the radeon fb.

if i can provide/assit you with testing, i am available to do so, also if you need more information
on my system.

i am subscribed to lkml, but i would like to be included into cc seprately, thx.


radeonfb_pci_register BEGIN
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
radeonfb (0000:05:00.0): Found 131072k of DDR 128 bits wide videoram
radeonfb (0000:05:00.0): mapped 16384k videoram
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=400.00 Mhz, System=300.00 MHz
radeonfb: PLL min 20000 max 40000
1 chips in connector info
- chip 1 has 2 connectors
* connector 0 of type 2 (CRT) : 2300
* connector 1 of type 3 (DVI-I) : 3221
Starting monitor auto detection...
radeonfb: I2C (port 1) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Display is GTF capable
hStart = 1344, hEnd = 1504, hTotal = 1728
vStart = 1025, vEnd = 1028, vTotal = 1072
h_total_disp = 0x9f00d7 hsync_strt_wid = 0x14054a
v_total_disp = 0x3ff042f vsync_strt_wid = 0x30400
pixclock = 6349
freq = 15750
freq = 15750, PLL min = 20000, PLL max = 40000
ref_div = 12, ref_clk = 2700, output_freq = 31500
ref_div = 12, ref_clk = 2700, output_freq = 31500
post div = 0x1
fb_div = 0x8c
ppll_div_3 = 0x1008c
Console: switching to colour frame buffer device 160x64
radeonfb (0000:05:00.0): ATI Radeon [b
radeonfb_pci_register END

-[00]-+-00.0 Intel Corp. 925X/XE Memory Controller Hub
+-01.0-[05]--+-00.0 ATI Technologies Inc RV370 5B62 [Radeon X600 (PCIE)]
| \-00.1 ATI Technologies Inc: Unknown device 5b72
+-1b.0 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller
+-1c.0-[04]--
+-1c.1-[03]----00.0 Marvell Technology Group Ltd. Gigabit Ethernet Controller
+-1c.2-[02]----00.0 Marvell Technology Group Ltd. Gigabit Ethernet Controller
+-1d.0 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
+-1d.1 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
+-1d.2 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
+-1d.3 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
+-1d.7 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
+-1e.0-[01]--+-00.0 Marvell Technology Group Ltd.: Unknown device 1fa7
| +-03.0 Texas Instruments TSB82AA2 IEEE-1394b Link Layer Controller
| +-04.0 Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded seems to be ITE8212)
| +-05.0 Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3114 [SATALink/SATARaid] Serial ATA Controller
| \-0a.0 Philips Semiconductors SAA7146
+-1f.0 Intel Corp. 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge
+-1f.1 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller
+-1f.2 Intel Corp. 82801FR/FRW (ICH6R/ICH6RW) SATA Controller
\-1f.3 Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller
0000:00:00.0 Host bridge: Intel Corp. 925X/XE Memory Controller Hub (rev 04)
Subsystem: Intel Corp.: Unknown device 2580
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [2109]

0000:00:01.0 PCI bridge: Intel Corp. 925X/XE PCI Express Root Port (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: d7f00000-d7ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Expansion ROM at 0000e000 [disabled] [size=4K]
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [a0] #10 [0141]

0000:00:1b.0 Class 0403: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 813d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d7bf4000 (64-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]

0000:00:1c.0 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Expansion ROM at 0000d000 [disabled] [size=4K]
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #10 [0141]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:1c.1 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d7e00000-d7efffff
Expansion ROM at 0000c000 [disabled] [size=4K]
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #10 [0141]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:1c.2 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 3 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: d7d00000-d7dfffff
Expansion ROM at 0000b000 [disabled] [size=4K]
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #10 [0141]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 7880 [size=32]

0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 7c00 [size=32]

0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 8000 [size=32]

0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 8080 [size=32]

0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d7bff800 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]

0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: d7c00000-d7cfffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]

0000:00:1f.0 ISA bridge: Intel Corp. 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

0000:00:1f.1 IDE interface: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]

0000:00:1f.2 Class 0106: Intel Corp. 82801FR/FRW (ICH6R/ICH6RW) SATA Controller (rev 03) (prog-if 01)
Subsystem: ASUSTeK Computer Inc.: Unknown device 2606
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 8c00
Region 1: I/O ports at 8880 [size=4]
Region 2: I/O ports at 8800 [size=8]
Region 3: I/O ports at 8480 [size=4]
Region 4: I/O ports at 8400 [size=16]
Region 5: Memory at d7bffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:1f.3 SMBus: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0400 [size=32]

0000:01:00.0 Ethernet controller: Marvell Technology Group Ltd.: Unknown device 1fa7 (rev 07)
Subsystem: ASUSTeK Computer Inc.: Unknown device 138f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 04
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d7ce0000 (32-bit, non-prefetchable)
Region 1: Memory at d7cb0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:03.0 FireWire (IEEE 1394): Texas Instruments TSB82AA2 IEEE-1394b Link Layer Controller (rev 01) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 813c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), cache line size 04
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d7cff000 (32-bit, non-prefetchable)
Region 1: Memory at d7cf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

0000:01:04.0 Unknown mass storage controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded seems (rev 13)
Subsystem: ASUSTeK Computer Inc.: Unknown device 813a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a080 [size=d7cc0000]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at 9c00 [size=8]
Region 3: I/O ports at 9880 [size=4]
Region 4: I/O ports at 9800 [size=16]
Expansion ROM at 00020000 [disabled]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:05.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
Subsystem: ASUSTeK Computer Inc.: Unknown device 8136
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 04
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ac00 [size=d7c00000]
Region 1: I/O ports at a880 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a480 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: Memory at d7cff800 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 00080000 [disabled]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:01:0a.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d7cffc00 (32-bit, non-prefetchable)

0000:02:00.0 Ethernet controller: Marvell Technology Group Ltd. Gigabit Ethernet Controller (rev 15)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
Latency: 0, cache line size 04
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d7dfc000 (64-bit, non-prefetchable) [size=d7dc0000]
Region 2: I/O ports at b800 [size=256]
Expansion ROM at 00020000 [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] #10 [0011]

0000:03:00.0 Ethernet controller: Marvell Technology Group Ltd. Gigabit Ethernet Controller (rev 15)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
Latency: 0, cache line size 04
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d7efc000 (64-bit, non-prefetchable) [size=d7ec0000]
Region 2: I/O ports at c800 [size=256]
Expansion ROM at 00020000 [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] #10 [0011]

0000:05:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B62 [Radeon X600 (PCIE)] (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 0450
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=d7fc0000]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at d7fe0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at 00020000 [disabled]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0001]
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

0000:05:00.1 Display controller: ATI Technologies Inc: Unknown device 5b72
Subsystem: PC Partner Limited: Unknown device 0451
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 04
Region 0: Memory at d7ff0000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0001]

Attachment: pgp00000.pgp
Description: PGP signature