aic7xxx boot error
From: Ermanno Poggi
Date: Tue Dec 21 2004 - 09:33:01 EST
Hello
From kernel 2.6.0, I've a problem with the aic7xxx driver (2.6.0-testXX was
ok).
Until 2.6.7 I can solve this issue deleting the original aic7xxx directory
in the kernel source and substitute this with the one downloaded from
http://people.freebsd.org/~gibbs/linux/ !
From 2.6.7 I can't do this anymore, because I get some error compiling the
kernel!
Can some one tell me if there is a solution, now I'm stuck with 2.6.7 and
can't upgrade my kernel!
The only thing that I've noticed is the ACPI row before the detection of
the aic7xxx, in the 2.6.X (where X>7) it could be an ACPI problem??
Obviously this problem prevent me to use any scsi device, with the new
kernel
Thanks in advance
Bye bye
---------kernel 2.6.9 with original aic7xxx driver------------
Zeus ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
Zeus scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
Zeus <Adaptec 2940 Ultra SCSI adapter>
Zeus aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Zeus
Zeus (scsi0:A:5): 20.000MB/s transfers (20.000MHz, offset 8)
Zeus scsi0:0:5:0: Attempting to queue an ABORT message
Zeus CDB: 0x12 0x0 0x0 0x0 0x24 0x0
Zeus scsi0: At time of recovery, card was not paused
Zeus >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
Zeus scsi0: Dumping Card State in Data-in phase, at SEQADDR 0x7c
Zeus Card was paused
Zeus ACCUM = 0x0, SINDEX = 0xb8, DINDEX = 0xa8, ARG_2 = 0x0
Zeus HCNT = 0x20 SCBPTR = 0x0
Zeus SCSISIGI[0x44] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x40]
Zeus SCSISEQ[0x12] SBLKCTL[0x0] SCSIRATE[0x8] SEQCTL[0x10]
Zeus SEQ_FLAGS[0x20] SSTAT0[0x0] SSTAT1[0x2] SSTAT2[0x0]
Zeus SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x80]
Zeus DFCNTRL[0x38] DFSTATUS[0x0]
Zeus STACK: 0x0 0x162 0x192 0x6e
Zeus SCB count = 4
Zeus Kernel NEXTQSCB = 2
Zeus Card NEXTQSCB = 2
Zeus QINFIFO entries:
Zeus Waiting Queue entries:
Zeus Disconnected Queue entries:
Zeus QOUTFIFO entries:
Zeus Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Zeus Sequencer SCB Info:
Zeus 0 SCB_CONTROL[0x0] SCB_SCSIID[0x57] SCB_LUN[0x0] SCB_TAG[0x3]
Zeus 1 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 2 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 3 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 4 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 5 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 6 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 7 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 8 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 9 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 10 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 11 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 12 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 13 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 14 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus 15 SCB_CONTROL[0x0] SCB_SCSIID[0xff] SCB_LUN[0xff] SCB_TAG[0xff]
Zeus Pending list:
Zeus 3 SCB_CONTROL[0x0] SCB_SCSIID[0x57] SCB_LUN[0x0]
Zeus Kernel Free SCB list: 1 0
Zeus Untagged Q(5): 3
Zeus DevQ(0:5:0): 0 waiting
Zeus
Zeus <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
Zeus scsi0:0:5:0: Device is active, asserting ATN
Zeus (scsi0:A:5:0): Abort Message Sent
Zeus Recovery code sleeping
Zeus (scsi0:A:5:0): SCB 3 - Abort Completed.
Zeus Recovery SCB completes
Zeus Recovery code awake
Zeus aic7xxx_abort returns 0x2002
Zeus (scsi0:A:5): 10.000MB/s transfers (10.000MHz, offset 8)
Zeus Vendor: PIONEER Model: DVD-ROM DVD-303F Rev: 2.00
Zeus Type: CD-ROM ANSI SCSI revision: 02
Zeus sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
Zeus Attached scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
Zeus Attached scsi generic sg0 at scsi0, channel 0, id 5, lun 0, type 5
---------kernel 2.6.7 with Gibbs aic7xxx driver------------
Zeus scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.3.9
Zeus <Adaptec 2940 Ultra SCSI adapter>
Zeus aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
Zeus
Zeus Vendor: PIONEER Model: DVD-ROM DVD-303F Rev: 2.00
Zeus Type: CD-ROM ANSI SCSI revision: 02
Zeus sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
Zeus Attached scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
Zeus Attached scsi generic sg0 at scsi0, channel 0, id 5, lun 0, type 5
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/