Re: pci-resume patch from 2.6.7-rc2 breakes S3 resume on somemachines

[Matthias Hentges]

Am Samstag, den 20.11.2004, 18:34 +1100 schrieb Benjamin Herrenschmidt:
> On Sat, 2004-11-20 at 04:36 +0100, Matthias Hentges wrote:
> > Am Samstag, den 20.11.2004, 02:43 +0000 schrieb Matthew Garrett:
> > > Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx> wrote:
> > > 

[...]

> > Trying to resume with radeonfb or X (DRI or fglrx) causes the machine
> > to freeze upon a resume.
> 
> At what point does it freeze ? Is the display back before the freeze ?

Sadly the video *never* comes back and stays dark no matter what I try:
- boot-radeon (int10 POST call) doesn't work. Either it segfaults or 
  it hangs the machine
- Any combination of radeontool light on|off doesn't help (no freeze,
sometimes it 
  can't read the cards mem address??)
- The int10 radeon patch for X11 doesn't help (freeze)
- radeonfb and / or X (either patched w/ int10 or not) freeze the
machine

I'm running out of ideas with this darn thing.
Since the serial port doesn't come back from S3 either, even a serial
console is of no help.

I have attached the output of lspci -vvv before and after resuming from
S3
The latter shows lots of "[disabled]" entries. Is that of any use?

Thanks
-- 
Matthias Hentges 
Cologne / Germany

[www.hentges.net] -> PGP welcome, HTML tolerated
ICQ: 97 26 97 4   -> No files, no URL's

My OS: Debian SID. Geek by Nature, Linux by Choice
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV250 5c63 [Radeon Mobility 9200 M9+] (rev 01) (prog-if 00 [VGA])
	Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d8000000 (32-bit, prefetchable) [disabled] [size=128M]
	Region 1: I/O ports at 3000 [disabled] [size=256]
	Region 2: [virtual] Memory at d0100000 (32-bit, non-prefetchable) [disabled] [size=64K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV250 5c63 [Radeon Mobility 9200 M9+] (rev 01) (prog-if 00 [VGA])
	Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 3000 [size=256]
	Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-