Problem accessing Sandisk CompactFlash Cards (Connected to the IDEbus)
From: Marc Strämke
Date: Sun Aug 29 2004 - 03:02:37 EST
Hello all,
Iam running an embedded system out of Compactflash. Kernel version is
2.4.27 (happens with all version i tried, 2.4.21-2.4.27).
The system is in use for a few month already, but i started to
experience problems with a newer revision of the Compactflash Cards from
Sandisk, when reading or writing to the device data gets corrupted and
the following message is written to the logfiles:
hdb: drive not ready for command
hdb: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdb: drive not ready for command
hdb: irq timeout: status=0xd0 { Busy }
ide0: reset: master: error (0x0a?)
I tried setting a longer WAIT_DRQ timeout in ide.h, but that doesnt
solve the problem (even with really large values, about 10 times the
default).
One thing which is interesting about the new card is that it isnt
detected by the kernel as a CFA device, but just a regular ATA device.
I attached the output of hdparm -I for both cards if that helps.
The IDE controller is a VIA VT82C586A/B/VT82C686/A/B/VT823x/A/C
(according to /proc/pci).
lspci -vv output is attached too.
Thanks in Advance for any suggestions to this problem.
Marc Strämke
Works:
CompactFlash ATA device, with removable media
Model Number: SanDisk SDCFB-128
Serial Number: 101913J0803Q3424
Firmware Revision: Vdi 1.24
Standards:
Likely used: 4
Configuration:
Logical max current
cylinders 980 497
heads 8 8
sectors/track 32 63
--
bytes/track: 0 bytes/sector: 576
CHS current addressable sectors: 250488
LBA user addressable sectors: 250880
device size with M = 1024*1024: 122 MBytes
device size with M = 1000*1000: 128 MBytes
Capabilities:
LBA, IORDY(may be)(cannot be disabled)
Buffer size: 1.0kB bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Vendor
R/W multiple sector transfer: Max = 1 Current = 1
DMA: not supported
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
does not works:
ATA device, with non-removable media
Model Number: SanDisk SDCFB-128
Serial Number: 109909E2004C5801
Firmware Revision: HDX 2.15
Standards:
Supported: 10
Likely used: 10
Configuration:
Logical max current
cylinders 980 980
heads 8 8
sectors/track 32 32
--
CHS current addressable sectors: 250880
LBA user addressable sectors: 250880
device size with M = 1024*1024: 122 MBytes
device size with M = 1000*1000: 128 MBytes
Capabilities:
LBA, IORDY(may be)(cannot be disabled)
Queue depth: 1
Standby timer values: spec'd by Vendor
R/W multiple sector transfer: Max = 1 Current = 1
DMA: mdma0 mdma1 *mdma2
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
00:00.0 Class 0600: 1106:0691 (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 Class 0604: 1106:8598
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e4000000-e5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Class 0601: 1106:0686 (rev 40)
Subsystem: 1106:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 Class 0101: 1106:0571 (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: 1106:0571
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 Class 0c03: 1106:3038 (rev 1a)
Subsystem: 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Class 0680: 1106:3057 (rev 40)
Subsystem: 1106:3057
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Class 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at e7042000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Class 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at e7040000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 Class ff00: 10b5:9050 (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at e7041000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at e000 [size=128]
Region 2: Memory at e7000000 (32-bit, non-prefetchable) [size=256K]
01:00.0 Class 0300: 102c:00c0 (rev 64)
Subsystem: 102c:00c0
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=256K]