Re: [bug?] usb device ok with ohci, fails to accept an address withuhci

From: Tommy Faasen
Date: Tue Jun 22 2004 - 17:43:46 EST

Next message: Tom Rini: "Re: [PATCH] ppc32: Cleanups & warning fixes of traps.c"
Previous message: Phy Prabab: "slow down with patch-2.6.7-mjb1"
In reply to: Tommy Faasen: "[bug?] usb device ok with ohci, fails to accept an address with uhci"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

thinkliberty wrote:

Is there an option for legacy support for USB in the BIOS?

No the closest thing is usb keyboard support, I tried both options.

Are You using a hub to connect the device? or is it directly in to the
USB port on the motherboard?

It's directly connected to the mainboard.

Regards,

Tommy

On Tue, 22 Jun 2004 21:58:49 +0200, Tommy Faasen <tommy@xxxxxxxxxxxxx> wrote:

Hi,

I have a sweex usb-wifi stick see also
http://sourceforge.net/projects/linux-lc100020/ and it's forums.
And I have 2 machines
Machine 1: Via kt133a chipset -> uhci_hcd
Machine 2: Sis 748 Chipset -> ohci_hcd

The device works without a problem on machine 2 with at least kernels
2.6.6 and 2.6.7.
The usb wifi stick fails to accept an address on machine 1. There is a
good faq about it with things you can try. (turn off acpi, irq for usb,
no irq sharing, removing all pci cards,etc) I tried everything but with
no luck.
I tried kernels 2.4.26 till and including 2.6.7 without luck, however on
the same machine is also connected an usb joystick that works without a
problem, so my usb does work.

The usb wifi stick is known to need to get a descriptor before settings
it's address but even with this patch I can't get it to work ( I didn't
need the patch for machine 2).

I read some usb specs/docs kernel usb stuff, but since I'm no expert I
cannot see where the problem is, therefore posted below is some
information that hopefully is helpfull to you.

Please let me know what else I can do to help,

Tommy

Dmesg output:
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: detected 2 ports
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb1: Manufacturer: Linux 2.6.7 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
PCI: Found IRQ 10 for device 0000:00:07.3
PCI: Sharing IRQ 10 with 0000:00:07.2
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:0b.0
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:07.3: irq 10, io base 0000d800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
usb usb2: Manufacturer: Linux 2.6.7 uhci_hcd
usb usb2: SerialNumber: 0000:00:07.3
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (cuhci_hcd 0000:00:07.2: port 1 portsc 01ab
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
usb 1-1: new low speed USB device using address 2
usb 1-1: skipped 1 descriptor after interface
usb 1-1: new device strings: Mfr=4, Product=32, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: WingMan Gamepad
usb 1-1: Manufacturer: Logitech Inc.
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
uhci_hcd 0000:00:07.2: port 2 portsc 018a
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.2: port 2 portsc 0188
hub 1-0:1.0: port 2 enable change, status 00000300
uhci_hcd 0000:00:07.3: port 1 portsc 018a
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.3: port 2 portsc 008a
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:07.3: port 1 portsc 0188
hub 2-0:1.0: port 1 enable change, status 00000300
uhci_hcd 0000:00:07.3: port 2 portsc 0088
hub 2-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:07.3: suspend_hc
uhci_hcd 0000:00:07.2: port 2 portsc 0093
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 1-2: new full speed USB device using address 3
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1
EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)

uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=69(IN) (buf=00000000)

uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=69(IN) (buf=00000000)

usb 1-2: device not accepting address 3, error -71
usb 1-2: new full speed USB device using address 4
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1
EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)

uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=69(IN) (buf=00000000)

uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
EndPt=0 Dev=0, PID=69(IN) (buf=00000000)

usb 1-2: device not accepting address 4, error -71
uhci_hcd 0000:00:07.2: port 2 portsc 008a
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:07.2: port 2 portsc 0088

lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
(rev 03)
Flags: bus master, medium devsel, latency 8
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
Capabilities: [80] Power Management version 2

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
(rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2

00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2

00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2

00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Flags: medium devsel, IRQ 7
Capabilities: [68] Power Management version 2

00:09.0 SCSI storage controller: Adaptec AHA-2940U2/W
Subsystem: Adaptec: Unknown device a180
Flags: bus master, medium devsel, latency 32, IRQ 11
BIST result: 00
I/O ports at dc00 [disabled] [size=256]
Memory at dd200000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1

00:0d.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05)
Subsystem: Compaq Computer Corporation NC3120
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dd203000 (32-bit, prefetchable) [size=4K]
I/O ports at ec00 [size=32]
Memory at dd100000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 1

01:00.0 VGA compatible controller: nVidia Corporation Vanta [NV6] (rev
15) (prog-if 00 [VGA])
Subsystem: Unknown device 17f2:4010
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at da000000 (32-bit, non-prefetchable) [size=16M]
Memory at d8000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 2.0

cat /proc/bus/usb/devices

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.7 uhci_hcd
S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
S: SerialNumber=0000:00:07.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.7 uhci_hcd
S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=046d ProdID=c209 Rev= 1.03
S: Manufacturer=Logitech Inc.
S: Product=WingMan Gamepad
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 40mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms

cat /proc/interrupts
CPU0
0: 2040665 XT-PIC timer
1: 8 XT-PIC i8042
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
10: 71185 XT-PIC EMU10K1, uhci_hcd, uhci_hcd, eth1
11: 19586 XT-PIC aic7xxx
12: 30728 XT-PIC Bt87x audio, bttv0, eth0
15: 18 XT-PIC ide1
NMI: 0
LOC: 2040654
ERR: 2234
MIS: 0

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Tom Rini: "Re: [PATCH] ppc32: Cleanups & warning fixes of traps.c"
Previous message: Phy Prabab: "slow down with patch-2.6.7-mjb1"
In reply to: Tommy Faasen: "[bug?] usb device ok with ohci, fails to accept an address with uhci"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]