[PATCH] PXA255 LCD Driver
From: Ian Campbell
Date: Wed Mar 17 2004 - 05:12:06 EST
Hi,
Attached is a patch against the most recent BK tree which implements a
driver for the on-chip LCD controller of the Xscale PXA255 processor. It
is based on the SA1100 FB driver and has been hacked on by various
people on the ARM mailing list.
I would appreciate a review of the code, any comments etc, with the aim
of getting the driver into good shape to be merged.
I posted it to the fbdev list @ sf.net (from MAINTAINERS) but that list
seems to be pretty quiet and www.linux-fbdev.org (also from MAINTAINERS)
seems to be down -- is there a more appropriate place these days for
framebuffer stuff?
Documentation/fb/pxafb.txt | 55 +
drivers/video/Kconfig | 27
drivers/video/Makefile | 2
drivers/video/fbmem.c | 5
drivers/video/pxafb.c | 1368 ++++++++++++++++++++++++++++++++++++
drivers/video/pxafb.h | 245 ++++++
include/asm-arm/arch-pxa/pxa-regs.h | 33
include/asm-arm/arch-pxa/pxafb.h | 68 +
8 files changed, 1795 insertions(+), 8 deletions(-)
Index: linux-2.6-bkpxa/Documentation/fb/pxafb.txt
===================================================================
--- linux-2.6-bkpxa.orig/Documentation/fb/pxafb.txt 2004-02-16 12:43:21.000000000 +0000
+++ linux-2.6-bkpxa/Documentation/fb/pxafb.txt 2004-03-17 09:30:50.000000000 +0000
@@ -0,0 +1,55 @@
+Driver for PXA25x LCD controller
+================================
+
+The driver supports the following options, either via
+options=<OPTIONS> when modular or video=pxafb:<OPTIONS> when built in.
+
+For example:
+ modprobe pxafb options=xres:640,yres:480,bpp:8,passive
+or on the kernel command line
+ video=pxafb:xres:640,yres:480,bpp:8,passive
+
+xres:XRES == LCCR1_PPL + 1
+yres:YRES == LLCR2_LPP + 1
+ The resolution of the display in pixels
+
+bpp:BPP
+ The bit depth. Valid values are 1, 2, 4, 8 and 16.
+
+pixclock:PIXCLOCK
+ Pixel clock in picoseconds
+
+left:LEFT == LCCR1_BLW + 1
+right:RIGHT == LCCR1_ELW + 1
+hsynclen:HSYNC == LCCR1_HSW + 1
+upper:UPPER == LCCR2_BFW
+lower:LOWER == LCCR2_EFR
+vsynclen:VSYNC == LCCR2_VSW + 1
+ Display margins and sync times
+
+color | mono => LCCR0_CMS
+ umm...
+
+active | passive => LCCR0_PAS
+ Active (TFT) or Passive (STN) display
+
+single | dual => LCCR0_SDS
+ Single or dual panel passive display
+
+4pix | 8pix => LCCR0_DPD
+ 4 or 8 pixel monochrome single panel data
+
+hsync:HSYNC
+vsync:VSYNC
+ Horizontal and vertical sync. 0 => active low, 1 => active
+ high.
+
+dpc:DPC
+ Double pixel clock. 1=>true, 0=>false
+
+outputen:POLARITY
+ Output Enable Polarity. 0 => active low, 1 => active high
+
+pixclockpol:POLARITY
+ pixel clock polarity
+ 0 => falling edge, 1 => rising edge
Index: linux-2.6-bkpxa/drivers/video/Kconfig
===================================================================
--- linux-2.6-bkpxa.orig/drivers/video/Kconfig 2004-03-17 09:13:19.000000000 +0000
+++ linux-2.6-bkpxa/drivers/video/Kconfig 2004-03-17 09:30:50.000000000 +0000
@@ -884,6 +884,33 @@
Say Y here if you want to support the built-in frame buffer of
the Motorola 68328 CPU family.
+config FB_PXA
+ tristate "PXA LCD framebuffer support"
+ depends on FB && ARCH_PXA
+ ---help---
+ Frame buffer driver for the built-in LCD controller in the Intel
+ PXA2x0 processor.
+
+ This driver is also available as a module ( = code which can be
+ inserted and removed from the running kernel whenever you want). The
+ module will be called vfb. If you want to compile it as a module,
+ say M here and read <file:Documentation/modules.txt>.
+
+ If unsure, say N.
+
+choice
+ prompt "LCD Bit Depth"
+ depends FB_PXA
+ default FB_PXA_8BPP
+
+config FB_PXA_8BPP
+ bool "8 bpp"
+
+config FB_PXA_16BPP
+ bool "16 bpp"
+
+endchoice
+
config FB_VIRTUAL
tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
depends on FB
Index: linux-2.6-bkpxa/drivers/video/Makefile
===================================================================
--- linux-2.6-bkpxa.orig/drivers/video/Makefile 2004-03-17 09:13:19.000000000 +0000
+++ linux-2.6-bkpxa/drivers/video/Makefile 2004-03-17 09:30:50.000000000 +0000
@@ -88,4 +88,4 @@
cfbfillrect.o
obj-$(CONFIG_FB_LEO) += leo.o sbuslib.o cfbimgblt.o cfbcopyarea.o \
cfbfillrect.o
-
+obj-$(CONFIG_FB_PXA) += pxafb.o cfbimgblt.o cfbcopyarea.o cfbfillrect.o
Index: linux-2.6-bkpxa/drivers/video/fbmem.c
===================================================================
--- linux-2.6-bkpxa.orig/drivers/video/fbmem.c 2004-03-17 09:13:19.000000000 +0000
+++ linux-2.6-bkpxa/drivers/video/fbmem.c 2004-03-17 09:30:50.000000000 +0000
@@ -112,6 +112,8 @@
extern int chips_init(void);
extern int g364fb_init(void);
extern int sa1100fb_init(void);
+extern int pxafb_init(void);
+extern int pxafb_setup(char*);
extern int fm2fb_init(void);
extern int fm2fb_setup(char*);
extern int q40fb_init(void);
@@ -341,6 +343,9 @@
#ifdef CONFIG_FB_SA1100
{ "sa1100fb", sa1100fb_init, NULL },
#endif
+#ifdef CONFIG_FB_PXA
+ { "pxafb", pxafb_init, pxafb_setup },
+#endif
#ifdef CONFIG_FB_SUN3
{ "sun3fb", sun3fb_init, sun3fb_setup },
#endif
Index: linux-2.6-bkpxa/drivers/video/pxafb.c
===================================================================
--- linux-2.6-bkpxa.orig/drivers/video/pxafb.c 2004-02-16 12:43:21.000000000 +0000
+++ linux-2.6-bkpxa/drivers/video/pxafb.c 2004-03-17 09:54:05.000000000 +0000
@@ -0,0 +1,1368 @@
+/*
+ * linux/drivers/video/pxafb.c
+ *
+ * Copyright (C) 1999 Eric A. Thomas.
+ * Copyright (C) 2004 Jean-Frederic Clere.
+ * Copyright (C) 2004 Ian Campbell.
+ * Copyright (C) 2004 Jeff Lackey.
+ * Based on acornfb.c Copyright (C) Russell King.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Intel PXA250/210 LCD Controller Frame Buffer Driver
+ *
+ * Please direct your questions and comments on this driver to the following
+ * email address:
+ *
+ * linux-arm-kernel@xxxxxxxxxxxxxxxxxxxxxx
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/fb.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#define DEBUG 0
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/uaccess.h>
+#include <asm/arch/bitfield.h>
+#include <asm/arch/pxafb.h>
+
+/*
+ * Complain if VAR is out of range.
+ */
+#define DEBUG_VAR 1
+
+#include "pxafb.h"
+
+/*
+ * Defining this is OK for consoles but it
+ * causes problems for windowing packages.
+ */
+#undef BLANKING_SET_PALETTE
+
+/* Bits which should not be set in machine configuration structures */
+#define LCCR0_INVALID_CONFIG_MASK (LCCR0_OUM|LCCR0_BM|LCCR0_QDM|LCCR0_DIS|LCCR0_EFM|LCCR0_IUM|LCCR0_SFM|LCCR0_LDM|LCCR0_ENB)
+#define LCCR3_INVALID_CONFIG_MASK (LCCR3_HSP|LCCR3_VSP|LCCR3_PCD|LCCR3_BPP)
+
+static void (*pxafb_backlight_power)(int);
+static void (*pxafb_lcd_power)(int);
+
+static int pxafb_activate_var(struct fb_var_screeninfo *var, struct pxafb_info *);
+static void set_ctrlr_state(struct pxafb_info *fbi, u_int state);
+
+#define PXAFB_OPTIONS_SIZE 256
+static char g_options[PXAFB_OPTIONS_SIZE] __initdata = "";
+
+static inline void pxafb_schedule_work(struct pxafb_info *fbi, u_int state)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ /*
+ * We need to handle two requests being made at the same time.
+ * There are two important cases:
+ * 1. When we are changing VT (C_REENABLE) while unblanking (C_ENABLE)
+ * We must perform the unblanking, which will do our REENABLE for us.
+ * 2. When we are blanking, but immediately unblank before we have
+ * blanked. We do the "REENABLE" thing here as well, just to be sure.
+ */
+ if (fbi->task_state == C_ENABLE && state == C_REENABLE)
+ state = (u_int) -1;
+ if (fbi->task_state == C_DISABLE && state == C_ENABLE)
+ state = C_REENABLE;
+
+ if (state != (u_int)-1) {
+ fbi->task_state = state;
+ schedule_work(&fbi->task);
+ }
+ local_irq_restore(flags);
+}
+
+static inline u_int chan_to_field(u_int chan, struct fb_bitfield *bf)
+{
+ chan &= 0xffff;
+ chan >>= 16 - bf->length;
+ return chan << bf->offset;
+}
+
+/*
+ * Convert bits-per-pixel to a hardware palette PBS value.
+ */
+static inline u_int palette_pbs(struct fb_var_screeninfo *var)
+{
+ int ret = 0;
+ switch (var->bits_per_pixel) {
+ case 4: ret = 0 << 12; break;
+ case 8: ret = 1 << 12; break;
+ case 16: ret = 2 << 12; break;
+ }
+ return ret;
+}
+
+static int
+pxafb_setpalettereg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int trans, struct fb_info *info)
+{
+ struct pxafb_info *fbi = (struct pxafb_info *)info;
+ u_int val, ret = 1;
+
+ if (regno < fbi->palette_size) {
+ val = ((red >> 0) & 0xf800);
+ val |= ((green >> 5) & 0x07e0);
+ val |= ((blue >> 11) & 0x001f);
+
+ if (regno == 0)
+ val |= palette_pbs(&fbi->fb.var);
+
+ fbi->palette_cpu[regno] = val;
+ ret = 0;
+ }
+ return ret;
+}
+
+static int
+pxafb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int trans, struct fb_info *info)
+{
+ struct pxafb_info *fbi = (struct pxafb_info *)info;
+ unsigned int val;
+ int ret = 1;
+
+ /*
+ * If inverse mode was selected, invert all the colours
+ * rather than the register number. The register number
+ * is what you poke into the framebuffer to produce the
+ * colour you requested.
+ */
+ if (fbi->cmap_inverse) {
+ red = 0xffff - red;
+ green = 0xffff - green;
+ blue = 0xffff - blue;
+ }
+
+ /*
+ * If greyscale is true, then we convert the RGB value
+ * to greyscale no matter what visual we are using.
+ */
+ if (fbi->fb.var.grayscale)
+ red = green = blue = (19595 * red + 38470 * green +
+ 7471 * blue) >> 16;
+
+ switch (fbi->fb.fix.visual) {
+ case FB_VISUAL_TRUECOLOR:
+ /*
+ * 12 or 16-bit True Colour. We encode the RGB value
+ * according to the RGB bitfield information.
+ */
+ if (regno <= 16) {
+ u32 *pal = fbi->fb.pseudo_palette;
+
+ val = chan_to_field(red, &fbi->fb.var.red);
+ val |= chan_to_field(green, &fbi->fb.var.green);
+ val |= chan_to_field(blue, &fbi->fb.var.blue);
+
+ pal[regno] = val;
+ ret = 0;
+ }
+ break;
+
+ case FB_VISUAL_STATIC_PSEUDOCOLOR:
+ case FB_VISUAL_PSEUDOCOLOR:
+ ret = pxafb_setpalettereg(regno, red, green, blue, trans, info);
+ break;
+ }
+
+ return ret;
+}
+
+/*
+ * pxafb_bpp_to_lccr3():
+ * Convert a bits per pixel value to the correct bit pattern for LCCR3
+ */
+static int pxafb_bpp_to_lccr3(struct fb_var_screeninfo *var)
+{
+ int ret = 0;
+ switch (var->bits_per_pixel) {
+ case 1: ret = LCCR3_1BPP; break;
+ case 2: ret = LCCR3_2BPP; break;
+ case 4: ret = LCCR3_4BPP; break;
+ case 8: ret = LCCR3_8BPP; break;
+ case 16: ret = LCCR3_16BPP; break;
+ }
+ return ret;
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * pxafb_display_dma_period()
+ * Calculate the minimum period (in picoseconds) between two DMA
+ * requests for the LCD controller. If we hit this, it means we're
+ * doing nothing but LCD DMA.
+ */
+static unsigned int pxafb_display_dma_period(struct fb_var_screeninfo *var)
+{
+ /*
+ * Period = pixclock * bits_per_byte * bytes_per_transfer
+ * / memory_bits_per_pixel;
+ */
+ return var->pixclock * 8 * 16 / var->bits_per_pixel;
+}
+
+extern unsigned int get_clk_frequency_khz(int info);
+#endif
+
+/*
+ * pxafb_check_var():
+ * Get the video params out of 'var'. If a value doesn't fit, round it up,
+ * if it's too big, return -EINVAL.
+ *
+ * Round up in the following order: bits_per_pixel, xres,
+ * yres, xres_virtual, yres_virtual, xoffset, yoffset, grayscale,
+ * bitfields, horizontal timing, vertical timing.
+ */
+static int pxafb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+ struct pxafb_info *fbi = (struct pxafb_info *)info;
+
+ if (var->xres < MIN_XRES)
+ var->xres = MIN_XRES;
+ if (var->yres < MIN_YRES)
+ var->yres = MIN_YRES;
+ if (var->xres > fbi->max_xres)
+ var->xres = fbi->max_xres;
+ if (var->yres > fbi->max_yres)
+ var->yres = fbi->max_yres;
+ var->xres_virtual =
+ max(var->xres_virtual, var->xres);
+ var->yres_virtual =
+ max(var->yres_virtual, var->yres);
+
+
+ DPRINTK("var->bits_per_pixel=%d\n", var->bits_per_pixel);
+ /*
+ * Setup the RGB parameters for this display.
+ *
+ * The pixel packing format is described on page 7-11 of the
+ * PXA2XX Developer's Manual.
+ */
+ if ( var->bits_per_pixel == 16 ) {
+ var->red.offset = 11; var->red.length = 5;
+ var->green.offset = 5; var->green.length = 6;
+ var->blue.offset = 0; var->blue.length = 5;
+ var->transp.offset = var->transp.length = 0;
+ } else {
+ var->red.offset = var->green.offset = var->blue.offset = var->transp.offset = 0;
+ var->red.length = 8;
+ var->green.length = 8;
+ var->blue.length = 8;
+ var->transp.length = 0;
+ }
+
+#ifdef CONFIG_CPU_FREQ
+ DPRINTK("dma period = %d ps, clock = %d kHz\n",
+ pxafb_display_dma_period(var),
+ get_clk_frequency_khz(0));
+#endif
+
+ return 0;
+}
+
+static inline void pxafb_set_truecolor(u_int is_true_color)
+{
+ DPRINTK("true_color = %d\n", is_true_color);
+ // do your machine-specific setup if needed
+}
+
+/*
+ * pxafb_set_par():
+ * Set the user defined part of the display for the specified console
+ */
+static int pxafb_set_par(struct fb_info *info)
+{
+ struct pxafb_info *fbi = (struct pxafb_info *)info;
+ struct fb_var_screeninfo *var = &info->var;
+ unsigned long palette_mem_size;
+
+ DPRINTK("set_par\n");
+
+ if (var->bits_per_pixel == 16)
+ fbi->fb.fix.visual = FB_VISUAL_TRUECOLOR;
+ else if (!fbi->cmap_static)
+ fbi->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR;
+ else {
+ /*
+ * Some people have weird ideas about wanting static
+ * pseudocolor maps. I suspect their user space
+ * applications are broken.
+ */
+ fbi->fb.fix.visual = FB_VISUAL_STATIC_PSEUDOCOLOR;
+ }
+
+ fbi->fb.fix.line_length = var->xres_virtual *
+ var->bits_per_pixel / 8;
+ fbi->palette_size = var->bits_per_pixel == 8 ? 256 : 16;
+
+ palette_mem_size = fbi->palette_size * sizeof(u16);
+
+ DPRINTK("palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);
+
+ fbi->palette_cpu = (u16 *)(fbi->map_cpu + PAGE_SIZE - palette_mem_size);
+ fbi->palette_dma = fbi->map_dma + PAGE_SIZE - palette_mem_size;
+
+ /*
+ * Set (any) board control register to handle new color depth
+ */
+ pxafb_set_truecolor(fbi->fb.fix.visual == FB_VISUAL_TRUECOLOR);
+
+ pxafb_activate_var(var, fbi);
+
+ return 0;
+}
+
+/*
+ * Formal definition of the VESA spec:
+ * On
+ * This refers to the state of the display when it is in full operation
+ * Stand-By
+ * This defines an optional operating state of minimal power reduction with
+ * the shortest recovery time
+ * Suspend
+ * This refers to a level of power management in which substantial power
+ * reduction is achieved by the display. The display can have a longer
+ * recovery time from this state than from the Stand-by state
+ * Off
+ * This indicates that the display is consuming the lowest level of power
+ * and is non-operational. Recovery from this state may optionally require
+ * the user to manually power on the monitor
+ *
+ * Now, the fbdev driver adds an additional state, (blank), where they
+ * turn off the video (maybe by colormap tricks), but don't mess with the
+ * video itself: think of it semantically between on and Stand-By.
+ *
+ * So here's what we should do in our fbdev blank routine:
+ *
+ * VESA_NO_BLANKING (mode 0) Video on, front/back light on
+ * VESA_VSYNC_SUSPEND (mode 1) Video on, front/back light off
+ * VESA_HSYNC_SUSPEND (mode 2) Video on, front/back light off
+ * VESA_POWERDOWN (mode 3) Video off, front/back light off
+ *
+ * This will match the matrox implementation.
+ */
+
+/*
+ * pxafb_blank():
+ * Blank the display by setting all palette values to zero. Note, the
+ * 12 and 16 bpp modes don't really use the palette, so this will not
+ * blank the display in all modes.
+ */
+static int pxafb_blank(int blank, struct fb_info *info)
+{
+ struct pxafb_info *fbi = (struct pxafb_info *)info;
+#if BLANKING_SET_PALETTE
+ int i;
+#endif
+
+ DPRINTK("pxafb_blank: blank=%d\n", blank);
+
+ switch (blank) {
+ case VESA_POWERDOWN:
+ case VESA_VSYNC_SUSPEND:
+ case VESA_HSYNC_SUSPEND:
+#if BLANKING_SET_PALETTE
+ // This is bad for windowing packages
+ if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
+ fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
+ for (i = 0; i < fbi->palette_size; i++)
+ pxafb_setpalettereg(i, 0, 0, 0, 0, info);
+#endif
+ pxafb_schedule_work(fbi, C_DISABLE);
+ //TODO if (pxafb_blank_helper) pxafb_blank_helper(blank);
+ break;
+
+ case VESA_NO_BLANKING:
+ //TODO if (pxafb_blank_helper) pxafb_blank_helper(blank);
+#if BLANKING_SET_PALETTE
+ if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
+ fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
+ fb_set_cmap(&fbi->fb.cmap, 1, info);
+#endif
+ pxafb_schedule_work(fbi, C_ENABLE);
+ }
+ return 0;
+}
+
+static struct fb_ops pxafb_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = pxafb_check_var,
+ .fb_set_par = pxafb_set_par,
+ .fb_setcolreg = pxafb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+ .fb_blank = pxafb_blank,
+ .fb_cursor = soft_cursor,
+};
+
+/*
+ * Calculate the PCD value from the clock rate (in picoseconds).
+ * We take account of the PPCR clock setting.
+ * From PXA Developer's Manual:
+ *
+ * PixelClock = LCLK
+ * -------------
+ * 2 ( PCD + 1 )
+ *
+ * PCD = LCLK
+ * ------------- - 1
+ * 2(PixelClock)
+ *
+ * Where:
+ * LCLK = LCD/Memory Clock
+ * PCD = LCCR3[7:0]
+ *
+ * PixelClock here is in Hz while the pixclock argument given is the
+ * period in picoseconds. Hence PixelClock = 1 / ( pixclock * 10^-12 )
+ *
+ * The function get_lclk_frequency_10khz returns LCLK in units of
+ * 10khz. Calling the result of this function lclk gives us the
+ * following
+ *
+ * PCD = (lclk * 10^4 ) * ( pixclock * 10^-12 )
+ * -------------------------------------- - 1
+ * 2
+ *
+ * Factoring the 10^4 and 10^-12 out gives 10^-8 == 1 / 100000000 as used below.
+ */
+static inline unsigned int get_pcd(unsigned int pixclock)
+{
+ unsigned long long pcd;
+
+ /* FIXME: Need to take into account Double Pixel Clock mode
+ * (DPC) bit? or perhaps set it based on the various clock
+ * speeds */
+
+ pcd = (unsigned long long)get_lclk_frequency_10khz() * (unsigned long long)pixclock;
+ pcd /= 100000000 * 2;
+ /* no need for this, since we should subtract 1 anyway. they cancel */
+ /* pcd += 1; */ /* make up for integer math truncations */
+ return (unsigned int)pcd;
+}
+
+/*
+ * pxafb_activate_var():
+ * Configures LCD Controller based on entries in var parameter. Settings are
+ * only written to the controller if changes were made.
+ */
+static int pxafb_activate_var(struct fb_var_screeninfo *var, struct pxafb_info *fbi)
+{
+ struct pxafb_lcd_reg new_regs;
+ u_long flags;
+ u_int pcd = get_pcd(var->pixclock);
+
+ DPRINTK("Configuring PXA LCD\n");
+
+ DPRINTK("var: xres=%d hslen=%d lm=%d rm=%d\n",
+ var->xres, var->hsync_len,
+ var->left_margin, var->right_margin);
+ DPRINTK("var: yres=%d vslen=%d um=%d bm=%d\n",
+ var->yres, var->vsync_len,
+ var->upper_margin, var->lower_margin);
+
+#if DEBUG_VAR
+ if (var->xres < 16 || var->xres > 1024)
+ printk(KERN_ERR "%s: invalid xres %d\n",
+ fbi->fb.fix.id, var->xres);
+ switch(var->bits_per_pixel) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ case 16:
+ break;
+ default:
+ printk(KERN_ERR "%s: invalid bit depth %d\n",
+ fbi->fb.fix.id, var->bits_per_pixel);
+ break;
+ }
+ if (var->hsync_len < 1 || var->hsync_len > 64)
+ printk(KERN_ERR "%s: invalid hsync_len %d\n",
+ fbi->fb.fix.id, var->hsync_len);
+ if (var->left_margin < 1 || var->left_margin > 255)
+ printk(KERN_ERR "%s: invalid left_margin %d\n",
+ fbi->fb.fix.id, var->left_margin);
+ if (var->right_margin < 1 || var->right_margin > 255)
+ printk(KERN_ERR "%s: invalid right_margin %d\n",
+ fbi->fb.fix.id, var->right_margin);
+ if (var->yres < 1 || var->yres > 1024)
+ printk(KERN_ERR "%s: invalid yres %d\n",
+ fbi->fb.fix.id, var->yres);
+ if (var->vsync_len < 1 || var->vsync_len > 64)
+ printk(KERN_ERR "%s: invalid vsync_len %d\n",
+ fbi->fb.fix.id, var->vsync_len);
+ if (var->upper_margin < 0 || var->upper_margin > 255)
+ printk(KERN_ERR "%s: invalid upper_margin %d\n",
+ fbi->fb.fix.id, var->upper_margin);
+ if (var->lower_margin < 0 || var->lower_margin > 255)
+ printk(KERN_ERR "%s: invalid lower_margin %d\n",
+ fbi->fb.fix.id, var->lower_margin);
+#endif
+
+ new_regs.lccr0 = fbi->lccr0 |
+ (LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM |
+ LCCR0_QDM | LCCR0_BM | LCCR0_OUM);
+
+ new_regs.lccr1 =
+ LCCR1_DisWdth(var->xres) +
+ LCCR1_HorSnchWdth(var->hsync_len) +
+ LCCR1_BegLnDel(var->left_margin) +
+ LCCR1_EndLnDel(var->right_margin);
+
+ new_regs.lccr2 =
+ LCCR2_DisHght(var->yres) +
+ LCCR2_VrtSnchWdth(var->vsync_len) +
+ LCCR2_BegFrmDel(var->upper_margin) +
+ LCCR2_EndFrmDel(var->lower_margin);
+
+#if defined(CONFIG_ARCH_LOOX600) || defined(CONFIG_ARCH_ADSBITSYX) || defined(CONFIG_ARCH_ADSAGX)
+ new_regs.lccr3 = fbi->lccr3;
+#else
+ new_regs.lccr3 = fbi->lccr3 |
+ pxafb_bpp_to_lccr3(var) |
+ (var->sync & FB_SYNC_HOR_HIGH_ACT ? LCCR3_HorSnchH : LCCR3_HorSnchL) |
+ (var->sync & FB_SYNC_VERT_HIGH_ACT ? LCCR3_VrtSnchH : LCCR3_VrtSnchL);
+
+ if (pcd)
+ new_regs.lccr3 |= LCCR3_PixClkDiv(pcd);
+#endif
+
+ DPRINTK("nlccr0 = 0x%08x\n", new_regs.lccr0);
+ DPRINTK("nlccr1 = 0x%08x\n", new_regs.lccr1);
+ DPRINTK("nlccr2 = 0x%08x\n", new_regs.lccr2);
+ DPRINTK("nlccr3 = 0x%08x\n", new_regs.lccr3);
+
+ /* Update shadow copy atomically */
+ local_irq_save(flags);
+
+ /* setup dma descriptors */
+ fbi->dmadesc_fblow_cpu = (struct pxafb_dma_descriptor *)((unsigned int)fbi->palette_cpu - 3*16);
+ fbi->dmadesc_fbhigh_cpu = (struct pxafb_dma_descriptor *)((unsigned int)fbi->palette_cpu - 2*16);
+ fbi->dmadesc_palette_cpu = (struct pxafb_dma_descriptor *)((unsigned int)fbi->palette_cpu - 1*16);
+
+ fbi->dmadesc_fblow_dma = fbi->palette_dma - 3*16;
+ fbi->dmadesc_fbhigh_dma = fbi->palette_dma - 2*16;
+ fbi->dmadesc_palette_dma = fbi->palette_dma - 1*16;
+
+ #define BYTES_PER_PANEL ((fbi->lccr0 & LCCR0_SDS) == LCCR0_Dual ? \
+ (var->xres * var->yres * var->bits_per_pixel / 8 / 2) : \
+ (var->xres * var->yres * var->bits_per_pixel / 8))
+
+ /* populate descriptors */
+ fbi->dmadesc_fblow_cpu->fdadr = fbi->dmadesc_fblow_dma;
+ fbi->dmadesc_fblow_cpu->fsadr = fbi->screen_dma + BYTES_PER_PANEL;
+ fbi->dmadesc_fblow_cpu->fidr = 0;
+ fbi->dmadesc_fblow_cpu->ldcmd = BYTES_PER_PANEL;
+
+ fbi->fdadr1 = fbi->dmadesc_fblow_dma; /* only used in dual-panel mode */
+
+ fbi->dmadesc_fbhigh_cpu->fsadr = fbi->screen_dma;
+ fbi->dmadesc_fbhigh_cpu->fidr = 0;
+ fbi->dmadesc_fbhigh_cpu->ldcmd = BYTES_PER_PANEL;
+
+ fbi->dmadesc_palette_cpu->fsadr = fbi->palette_dma;
+ fbi->dmadesc_palette_cpu->fidr = 0;
+ fbi->dmadesc_palette_cpu->ldcmd = (fbi->palette_size * 2) | LDCMD_PAL;
+
+ if( var->bits_per_pixel < 12)
+ {
+ /* assume any mode with <12 bpp is palette driven */
+ fbi->dmadesc_palette_cpu->fdadr = fbi->dmadesc_fbhigh_dma;
+ fbi->dmadesc_fbhigh_cpu->fdadr = fbi->dmadesc_palette_dma;
+ fbi->fdadr0 = fbi->dmadesc_palette_dma; /* flips back and forth between pal and fbhigh */
+ }
+ else
+ {
+ /* palette shouldn't be loaded in true-color mode */
+ fbi->dmadesc_fbhigh_cpu->fdadr = fbi->dmadesc_fbhigh_dma;
+ fbi->fdadr0 = fbi->dmadesc_fbhigh_dma; /* no pal just fbhigh */
+ /* init it to something, even though we won't be using it */
+ fbi->dmadesc_palette_cpu->fdadr = fbi->dmadesc_palette_dma;
+ }
+
+#if 0
+ DPRINTK("fbi->dmadesc_fblow_cpu = 0x%p\n", fbi->dmadesc_fblow_cpu);
+ DPRINTK("fbi->dmadesc_fbhigh_cpu = 0x%p\n", fbi->dmadesc_fbhigh_cpu);
+ DPRINTK("fbi->dmadesc_palette_cpu = 0x%p\n", fbi->dmadesc_palette_cpu);
+ DPRINTK("fbi->dmadesc_fblow_dma = 0x%x\n", fbi->dmadesc_fblow_dma);
+ DPRINTK("fbi->dmadesc_fbhigh_dma = 0x%x\n", fbi->dmadesc_fbhigh_dma);
+ DPRINTK("fbi->dmadesc_palette_dma = 0x%x\n", fbi->dmadesc_palette_dma);
+
+ DPRINTK("fbi->dmadesc_fblow_cpu->fdadr = 0x%x\n", fbi->dmadesc_fblow_cpu->fdadr);
+ DPRINTK("fbi->dmadesc_fbhigh_cpu->fdadr = 0x%x\n", fbi->dmadesc_fbhigh_cpu->fdadr);
+ DPRINTK("fbi->dmadesc_palette_cpu->fdadr = 0x%x\n", fbi->dmadesc_palette_cpu->fdadr);
+
+ DPRINTK("fbi->dmadesc_fblow_cpu->fsadr = 0x%x\n", fbi->dmadesc_fblow_cpu->fsadr);
+ DPRINTK("fbi->dmadesc_fbhigh_cpu->fsadr = 0x%x\n", fbi->dmadesc_fbhigh_cpu->fsadr);
+ DPRINTK("fbi->dmadesc_palette_cpu->fsadr = 0x%x\n", fbi->dmadesc_palette_cpu->fsadr);
+
+ DPRINTK("fbi->dmadesc_fblow_cpu->ldcmd = 0x%x\n", fbi->dmadesc_fblow_cpu->ldcmd);
+ DPRINTK("fbi->dmadesc_fbhigh_cpu->ldcmd = 0x%x\n", fbi->dmadesc_fbhigh_cpu->ldcmd);
+ DPRINTK("fbi->dmadesc_palette_cpu->ldcmd = 0x%x\n", fbi->dmadesc_palette_cpu->ldcmd);
+#endif
+
+ fbi->reg_lccr0 = new_regs.lccr0;
+ fbi->reg_lccr1 = new_regs.lccr1;
+ fbi->reg_lccr2 = new_regs.lccr2;
+ fbi->reg_lccr3 = new_regs.lccr3;
+ local_irq_restore(flags);
+
+ /*
+ * Only update the registers if the controller is enabled
+ * and something has changed.
+ */
+ if ((LCCR0 != fbi->reg_lccr0) || (LCCR1 != fbi->reg_lccr1) ||
+ (LCCR2 != fbi->reg_lccr2) || (LCCR3 != fbi->reg_lccr3) ||
+ (FDADR0 != fbi->fdadr0) || (FDADR1 != fbi->fdadr1))
+ pxafb_schedule_work(fbi, C_REENABLE);
+
+ return 0;
+}
+
+/*
+ * NOTE! The following functions are purely helpers for set_ctrlr_state.
+ * Do not call them directly; set_ctrlr_state does the correct serialisation
+ * to ensure that things happen in the right way 100% of time time.
+ * -- rmk
+ */
+static inline void __pxafb_backlight_power(struct pxafb_info *fbi, int on)
+{
+ DPRINTK("backlight o%s\n", on ? "n" : "ff");
+
+ if (pxafb_backlight_power)
+ pxafb_backlight_power(on);
+}
+
+static inline void __pxafb_lcd_power(struct pxafb_info *fbi, int on)
+{
+ DPRINTK("LCD power o%s\n", on ? "n" : "ff");
+
+ if (pxafb_lcd_power)
+ pxafb_lcd_power(on);
+}
+
+static void pxafb_setup_gpio(struct pxafb_info *fbi)
+{
+ unsigned int lccr0 = fbi->lccr0;
+
+ /*
+ * setup is based on type of panel supported
+ */
+
+ /* 4 bit interface */
+ if ((lccr0 & LCCR0_CMS) == LCCR0_Mono &&
+ (lccr0 & LCCR0_SDS) == LCCR0_Sngl &&
+ (lccr0 & LCCR0_DPD) == LCCR0_4PixMono)
+ {
+ // bits 58-61
+ GPDR1 |= (0xf << 26);
+ GAFR1_U = (GAFR1_U & ~(0xff << 20)) | (0xaa << 20);
+
+ // bits 74-77
+ GPDR2 |= (0xf << 10);
+ GAFR2_L = (GAFR2_L & ~(0xff << 20)) | (0xaa << 20);
+ }
+
+ /* 8 bit interface */
+ else if (((lccr0 & LCCR0_CMS) == LCCR0_Mono &&
+ ((lccr0 & LCCR0_SDS) == LCCR0_Dual || (lccr0 & LCCR0_DPD) == LCCR0_8PixMono)) ||
+ ((lccr0 & LCCR0_CMS) == LCCR0_Color &&
+ (lccr0 & LCCR0_PAS) == LCCR0_Pas && (lccr0 & LCCR0_SDS) == LCCR0_Sngl))
+ {
+ // bits 58-65
+ GPDR1 |= (0x3f << 26);
+ GPDR2 |= (0x3);
+
+ GAFR1_U = (GAFR1_U & ~(0xfff << 20)) | (0xaaa << 20);
+ GAFR2_L = (GAFR2_L & ~0xf) | (0xa);
+
+ // bits 74-77
+ GPDR2 |= (0xf << 10);
+ GAFR2_L = (GAFR2_L & ~(0xff << 20)) | (0xaa << 20);
+ }
+
+ /* 16 bit interface */
+ else if ((lccr0 & LCCR0_CMS) == LCCR0_Color &&
+ ((lccr0 & LCCR0_SDS) == LCCR0_Dual || (lccr0 & LCCR0_PAS) == LCCR0_Act))
+ {
+ // bits 58-77
+ GPDR1 |= (0x3f << 26);
+ GPDR2 |= 0x00003fff;
+
+ GAFR1_U = (GAFR1_U & ~(0xfff << 20)) | (0xaaa << 20);
+ GAFR2_L = (GAFR2_L & 0xf0000000) | 0x0aaaaaaa;
+ }
+
+ else {
+ printk( KERN_ERR "pxafb_setup_gpio: unable to determine bits per pixel\n");
+ }
+}
+
+static void pxafb_enable_controller(struct pxafb_info *fbi)
+{
+ DPRINTK("Enabling LCD controller\n");
+ DPRINTK("fdadr0 0x%08x\n", (unsigned int) fbi->fdadr0);
+ DPRINTK("fdadr1 0x%08x\n", (unsigned int) fbi->fdadr1);
+ DPRINTK("reg_lccr0 0x%08x\n", (unsigned int) fbi->reg_lccr0);
+ DPRINTK("reg_lccr1 0x%08x\n", (unsigned int) fbi->reg_lccr1);
+ DPRINTK("reg_lccr2 0x%08x\n", (unsigned int) fbi->reg_lccr2);
+ DPRINTK("reg_lccr3 0x%08x\n", (unsigned int) fbi->reg_lccr3);
+
+ /*
+ * Make sure the mode bits are present in the first palette entry
+ */
+ //TODO pxafb had: fbi->palette_cpu[0] &= 0xcfff;
+ //TODO pxafb had: fbi->palette_cpu[0] |= palette_pbs(&fbi->fb.var);
+
+ /* Sequence from 11.7.10 */
+ LCCR3 = fbi->reg_lccr3;
+ LCCR2 = fbi->reg_lccr2;
+ LCCR1 = fbi->reg_lccr1;
+ LCCR0 = fbi->reg_lccr0 & ~LCCR0_ENB;
+
+ FDADR0 = fbi->fdadr0;
+ FDADR1 = fbi->fdadr1;
+ LCCR0 |= LCCR0_ENB;
+
+ DPRINTK("FDADR0 0x%08x\n", (unsigned int) FDADR0);
+ DPRINTK("FDADR1 0x%08x\n", (unsigned int) FDADR1);
+ DPRINTK("LCCR0 0x%08x\n", (unsigned int) LCCR0);
+ DPRINTK("LCCR1 0x%08x\n", (unsigned int) LCCR1);
+ DPRINTK("LCCR2 0x%08x\n", (unsigned int) LCCR2);
+ DPRINTK("LCCR3 0x%08x\n", (unsigned int) LCCR3);
+}
+
+static void pxafb_disable_controller(struct pxafb_info *fbi)
+{
+ DECLARE_WAITQUEUE(wait, current);
+
+ DPRINTK("Disabling LCD controller\n");
+
+ add_wait_queue(&fbi->ctrlr_wait, &wait);
+ set_current_state(TASK_UNINTERRUPTIBLE);
+
+ LCSR = 0xffffffff; /* Clear LCD Status Register */
+ LCCR0 &= ~LCCR0_LDM; /* Enable LCD Disable Done Interrupt */
+ //TODO?enable_irq(IRQ_LCD); /* Enable LCD IRQ */
+ LCCR0 &= ~LCCR0_ENB; /* Disable LCD Controller */
+
+ schedule_timeout(20 * HZ / 1000);
+ set_current_state(TASK_RUNNING);
+ remove_wait_queue(&fbi->ctrlr_wait, &wait);
+}
+
+/*
+ * pxafb_handle_irq: Handle 'LCD DONE' interrupts.
+ */
+static irqreturn_t pxafb_handle_irq(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct pxafb_info *fbi = dev_id;
+ unsigned int lcsr = LCSR;
+
+ if (lcsr & LCSR_LDD) {
+ LCCR0 |= LCCR0_LDM;
+ wake_up(&fbi->ctrlr_wait);
+ }
+
+ LCSR = lcsr;
+ return IRQ_HANDLED;
+}
+
+/*
+ * This function must be called from task context only, since it will
+ * sleep when disabling the LCD controller, or if we get two contending
+ * processes trying to alter state.
+ */
+static void set_ctrlr_state(struct pxafb_info *fbi, u_int state)
+{
+ u_int old_state;
+
+ down(&fbi->ctrlr_sem);
+
+ old_state = fbi->state;
+
+ /*
+ * Hack around fbcon initialisation.
+ */
+ if (old_state == C_STARTUP && state == C_REENABLE)
+ state = C_ENABLE;
+
+ switch (state) {
+ case C_DISABLE_CLKCHANGE:
+ /*
+ * Disable controller for clock change. If the
+ * controller is already disabled, then do nothing.
+ */
+ if (old_state != C_DISABLE && old_state != C_DISABLE_PM) {
+ fbi->state = state;
+ //TODO __pxafb_lcd_power(fbi, 0);
+ pxafb_disable_controller(fbi);
+ }
+ break;
+
+ case C_DISABLE_PM:
+ case C_DISABLE:
+ /*
+ * Disable controller
+ */
+ if (old_state != C_DISABLE) {
+ fbi->state = state;
+ __pxafb_backlight_power(fbi, 0);
+ __pxafb_lcd_power(fbi, 0);
+ if (old_state != C_DISABLE_CLKCHANGE)
+ pxafb_disable_controller(fbi);
+ }
+ break;
+
+ case C_ENABLE_CLKCHANGE:
+ /*
+ * Enable the controller after clock change. Only
+ * do this if we were disabled for the clock change.
+ */
+ if (old_state == C_DISABLE_CLKCHANGE) {
+ fbi->state = C_ENABLE;
+ pxafb_enable_controller(fbi);
+ //TODO __pxafb_lcd_power(fbi, 1);
+ }
+ break;
+
+ case C_REENABLE:
+ /*
+ * Re-enable the controller only if it was already
+ * enabled. This is so we reprogram the control
+ * registers.
+ */
+ if (old_state == C_ENABLE) {
+ pxafb_disable_controller(fbi);
+ pxafb_setup_gpio(fbi);
+ pxafb_enable_controller(fbi);
+ }
+ break;
+
+ case C_ENABLE_PM:
+ /*
+ * Re-enable the controller after PM. This is not
+ * perfect - think about the case where we were doing
+ * a clock change, and we suspended half-way through.
+ */
+ if (old_state != C_DISABLE_PM)
+ break;
+ /* fall through */
+
+ case C_ENABLE:
+ /*
+ * Power up the LCD screen, enable controller, and
+ * turn on the backlight.
+ */
+ if (old_state != C_ENABLE) {
+ fbi->state = C_ENABLE;
+ pxafb_setup_gpio(fbi);
+ pxafb_enable_controller(fbi);
+ __pxafb_lcd_power(fbi, 1);
+ __pxafb_backlight_power(fbi, 1);
+ }
+ break;
+ }
+ up(&fbi->ctrlr_sem);
+}
+
+/*
+ * Our LCD controller task (which is called when we blank or unblank)
+ * via keventd.
+ */
+static void pxafb_task(void *dummy)
+{
+ struct pxafb_info *fbi = dummy;
+ u_int state = xchg(&fbi->task_state, -1);
+
+ set_ctrlr_state(fbi, state);
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * CPU clock speed change handler. We need to adjust the LCD timing
+ * parameters when the CPU clock is adjusted by the power management
+ * subsystem.
+ *
+ * TODO: Determine why f->new != 10*get_lclk_frequency_10khz()
+ */
+static int
+pxafb_freq_transition(struct notifier_block *nb, unsigned long val, void *data)
+{
+ struct pxafb_info *fbi = TO_INF(nb, freq_transition);
+ //TODO struct cpufreq_freqs *f = data;
+ u_int pcd;
+
+ switch (val) {
+ case CPUFREQ_PRECHANGE:
+ set_ctrlr_state(fbi, C_DISABLE_CLKCHANGE);
+ break;
+
+ case CPUFREQ_POSTCHANGE:
+ pcd = get_pcd(fbi->fb.var.pixclock);
+ fbi->reg_lccr3 = (fbi->reg_lccr3 & ~0xff) | LCCR3_PixClkDiv(pcd);
+ set_ctrlr_state(fbi, C_ENABLE_CLKCHANGE);
+ break;
+ }
+ return 0;
+}
+
+static int
+pxafb_freq_policy(struct notifier_block *nb, unsigned long val, void *data)
+{
+ struct pxafb_info *fbi = TO_INF(nb, freq_policy);
+ struct fb_var_screeninfo *var = &fbi->fb.var;
+ struct cpufreq_policy *policy = data;
+
+ switch (val) {
+ case CPUFREQ_ADJUST:
+ case CPUFREQ_INCOMPATIBLE:
+ printk(KERN_DEBUG "min dma period: %d ps, "
+ "new clock %d kHz\n", pxafb_display_dma_period(var),
+ policy->max);
+ // TODO: fill in min/max values
+ break;
+#if 0
+ case CPUFREQ_NOTIFY:
+ printk(KERN_ERR "%s: got CPUFREQ_NOTIFY\n", __FUNCTION__);
+ do {} while(0);
+ /* todo: panic if min/max values aren't fulfilled
+ * [can't really happen unless there's a bug in the
+ * CPU policy verification process *
+ */
+ break;
+#endif
+ }
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_PM
+/*
+ * Power management hooks. Note that we won't be called from IRQ context,
+ * unlike the blank functions above, so we may sleep.
+ */
+static int pxafb_suspend(struct device *dev, u32 state, u32 level)
+{
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
+
+ if (level == SUSPEND_DISABLE || level == SUSPEND_POWER_DOWN)
+ set_ctrlr_state(fbi, C_DISABLE_PM);
+ return 0;
+}
+
+static int pxafb_resume(struct device *dev, u32 level)
+{
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
+
+ if (level == RESUME_ENABLE)
+ set_ctrlr_state(fbi, C_ENABLE_PM);
+ return 0;
+}
+#else
+#define pxafb_suspend NULL
+#define pxafb_resume NULL
+#endif
+
+/*
+ * pxafb_map_video_memory():
+ * Allocates the DRAM memory for the frame buffer. This buffer is
+ * remapped into a non-cached, non-buffered, memory region to
+ * allow palette and pixel writes to occur without flushing the
+ * cache. Once this area is remapped, all virtual memory
+ * access to the video memory should occur at the new region.
+ */
+static int __init pxafb_map_video_memory(struct pxafb_info *fbi)
+{
+ u_long palette_mem_size;
+
+ /*
+ * We reserve one page for the palette, plus the size
+ * of the framebuffer.
+ */
+ fbi->map_size = PAGE_ALIGN(fbi->fb.fix.smem_len + PAGE_SIZE);
+ fbi->map_cpu = consistent_alloc(GFP_KERNEL, fbi->map_size,
+ &fbi->map_dma, PTE_BUFFERABLE);
+
+ if (fbi->map_cpu) {
+ /* prevent initial garbage on screen */
+ memset(fbi->map_cpu, 0, fbi->map_size);
+ fbi->fb.screen_base = fbi->map_cpu + PAGE_SIZE;
+ fbi->screen_dma = fbi->map_dma + PAGE_SIZE;
+ fbi->fb.fix.smem_start = fbi->screen_dma;
+
+ fbi->palette_size = fbi->fb.var.bits_per_pixel == 8 ? 256 : 16;
+
+ palette_mem_size = fbi->palette_size * sizeof(u16);
+ DPRINTK("palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);
+
+ fbi->palette_cpu = (u16 *)(fbi->map_cpu + PAGE_SIZE - palette_mem_size);
+ fbi->palette_dma = fbi->map_dma + PAGE_SIZE - palette_mem_size;
+ }
+
+ return fbi->map_cpu ? 0 : -ENOMEM;
+}
+
+/* Fake monspecs to fill in fbinfo structure */
+static struct fb_monspecs monspecs __initdata = {
+ 30000, 70000, 50, 65, 0 /* Generic */
+};
+
+
+
+static struct pxafb_info * __init pxafb_init_fbinfo(struct pxafb_mach_info *inf)
+{
+ struct pxafb_info *fbi;
+ void *addr;
+
+ /* Alloc the pxafb_info and pseudo_palette in one step */
+ fbi = kmalloc(sizeof(struct pxafb_info) + sizeof(u32) * 17, GFP_KERNEL);
+ if (!fbi)
+ return NULL;
+
+ memset(fbi, 0, sizeof(struct pxafb_info));
+
+ strcpy(fbi->fb.fix.id, PXA_NAME);
+
+ fbi->fb.fix.type = FB_TYPE_PACKED_PIXELS;
+ fbi->fb.fix.type_aux = 0;
+ fbi->fb.fix.xpanstep = 0;
+ fbi->fb.fix.ypanstep = 0;
+ fbi->fb.fix.ywrapstep = 0;
+ fbi->fb.fix.accel = FB_ACCEL_NONE;
+
+ fbi->fb.var.nonstd = 0;
+ fbi->fb.var.activate = FB_ACTIVATE_NOW;
+ fbi->fb.var.height = -1;
+ fbi->fb.var.width = -1;
+ fbi->fb.var.accel_flags = 0;
+ fbi->fb.var.vmode = FB_VMODE_NONINTERLACED;
+
+ fbi->fb.fbops = &pxafb_ops;
+ fbi->fb.flags = FBINFO_FLAG_DEFAULT;
+ fbi->fb.node = -1;
+ fbi->fb.monspecs = monspecs;
+ fbi->fb.currcon = -1;
+
+ addr = fbi;
+ addr = addr + sizeof(struct pxafb_info);
+ fbi->fb.pseudo_palette = addr;
+
+ fbi->max_xres = inf->xres;
+ fbi->fb.var.xres = inf->xres;
+ fbi->fb.var.xres_virtual = inf->xres;
+ fbi->max_yres = inf->yres;
+ fbi->fb.var.yres = inf->yres;
+ fbi->fb.var.yres_virtual = inf->yres;
+ fbi->max_bpp = inf->bpp;
+ fbi->fb.var.bits_per_pixel = inf->bpp;
+ fbi->fb.var.pixclock = inf->pixclock;
+ fbi->fb.var.hsync_len = inf->hsync_len;
+ fbi->fb.var.left_margin = inf->left_margin;
+ fbi->fb.var.right_margin = inf->right_margin;
+ fbi->fb.var.vsync_len = inf->vsync_len;
+ fbi->fb.var.upper_margin = inf->upper_margin;
+ fbi->fb.var.lower_margin = inf->lower_margin;
+ fbi->fb.var.sync = inf->sync;
+ fbi->fb.var.grayscale = inf->cmap_greyscale;
+ fbi->cmap_inverse = inf->cmap_inverse;
+ fbi->cmap_static = inf->cmap_static;
+ fbi->lccr0 = inf->lccr0;
+ fbi->lccr3 = inf->lccr3;
+ fbi->state = C_STARTUP;
+ fbi->task_state = (u_char)-1;
+ fbi->fb.fix.smem_len = fbi->max_xres * fbi->max_yres *
+ fbi->max_bpp / 8;
+
+ init_waitqueue_head(&fbi->ctrlr_wait);
+ INIT_WORK(&fbi->task, pxafb_task, fbi);
+ init_MUTEX(&fbi->ctrlr_sem);
+
+ return fbi;
+}
+
+static int __init pxafb_parse_options(struct device *dev, struct pxafb_mach_info *inf, char *options)
+{
+ /*
+ */
+ char *this_opt;
+
+ if (!options || !*options)
+ return 0;
+
+ dev_dbg(dev, "options are \"%s\"\n", options ? options : "null");
+
+ /* could be made table driven or similar?... */
+ while ((this_opt = strsep(&options, ",")) != NULL) {
+ if (!strncmp(this_opt, "xres:", 5)) {
+ inf->xres = simple_strtoul(this_opt+5, NULL, 0);
+ dev_info(dev, "override xres: %d\n", inf->xres);
+ } else if (!strncmp(this_opt, "yres:", 5)) {
+ inf->yres = simple_strtoul(this_opt+5, NULL, 0);
+ dev_info(dev, "override yres: %d\n", inf->yres);
+ } else if (!strncmp(this_opt, "bpp:", 4)) {
+ inf->bpp = simple_strtoul(this_opt+4, NULL, 0);
+ dev_info(dev, "override bpp: %d\n", inf->bpp);
+ } else if (!strncmp(this_opt, "pixclock:", 9)) {
+ inf->pixclock = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override pixclock: %uld\n", inf->pixclock);
+ } else if (!strncmp(this_opt, "left:", 5)) {
+ inf->left_margin = simple_strtoul(this_opt+5, NULL, 0);
+ dev_info(dev, "override left: %d\n", inf->left_margin);
+ } else if (!strncmp(this_opt, "right:", 6)) {
+ inf->right_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override right: %d\n", inf->right_margin);
+ } else if (!strncmp(this_opt, "upper:", 6)) {
+ inf->upper_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override upper: %d\n", inf->upper_margin);
+ } else if (!strncmp(this_opt, "lower:", 6)) {
+ inf->lower_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override lower: %d\n", inf->lower_margin);
+ } else if (!strncmp(this_opt, "hsynclen:", 9)) {
+ inf->hsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override hsynclen: %d\n", inf->hsync_len);
+ } else if (!strncmp(this_opt, "vsynclen:", 9)) {
+ inf->vsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override vsynclen: %d\n", inf->vsync_len);
+ } else if (!strncmp(this_opt, "hsync:", 6)) {
+ if ( simple_strtoul(this_opt+6, NULL, 0) == 0 ) {
+ dev_info(dev, "override hsync: Active Low\n");
+ inf->sync &= ~FB_SYNC_HOR_HIGH_ACT;
+ } else {
+ dev_info(dev, "override hsync: Active High\n");
+ inf->sync |= FB_SYNC_HOR_HIGH_ACT;
+ }
+ } else if (!strncmp(this_opt, "vsync:", 6)) {
+ if ( simple_strtoul(this_opt+6, NULL, 0) == 0 ) {
+ dev_info(dev, "override vsync: Active Low\n");
+ inf->sync &= ~FB_SYNC_VERT_HIGH_ACT;
+ } else {
+ dev_info(dev, "override vsync: Active High\n");
+ inf->sync |= FB_SYNC_VERT_HIGH_ACT;
+ }
+ } else if (!strncmp(this_opt, "dpc:", 4)) {
+ if ( simple_strtoul(this_opt+4, NULL, 0) == 0 ) {
+ dev_info(dev, "override double pixel clock: false\n");
+ inf->lccr3 &= ~LCCR3_DPC;
+ } else {
+ dev_info(dev, "override double pixel clock: true\n");
+ inf->lccr3 |= LCCR3_DPC;
+ }
+ } else if (!strncmp(this_opt, "outputen:", 9)) {
+ if ( simple_strtoul(this_opt+9, NULL, 0) == 0 ) {
+ dev_info(dev, "override output enable: active low\n");
+ inf->lccr3 = ( inf->lccr3 & ~LCCR3_OEP ) | LCCR3_OutEnL;
+ } else {
+ dev_info(dev, "override output enable: active high\n");
+ inf->lccr3 = ( inf->lccr3 & ~LCCR3_OEP ) | LCCR3_OutEnH;
+ }
+ } else if (!strncmp(this_opt, "pixclockpol:", 12)) {
+ if ( simple_strtoul(this_opt+12, NULL, 0) == 0 ) {
+ dev_info(dev, "override pixel clock polarity: falling edge\n");
+ inf->lccr3 = ( inf->lccr3 & ~LCCR3_PCP ) | LCCR3_PixFlEdg;
+ } else {
+ dev_info(dev, "override pixel clock polarity: rising edge\n");
+ inf->lccr3 = ( inf->lccr3 & ~LCCR3_PCP ) | LCCR3_PixRsEdg;
+ }
+ } else if (!strncmp(this_opt, "color", 5)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_CMS) | LCCR0_Color;
+ } else if (!strncmp(this_opt, "mono", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_CMS) | LCCR0_Mono;
+ } else if (!strncmp(this_opt, "active", 6)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_PAS) | LCCR0_Act;
+ } else if (!strncmp(this_opt, "passive", 7)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_PAS) | LCCR0_Pas;
+ } else if (!strncmp(this_opt, "single", 6)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_SDS) | LCCR0_Sngl;
+ } else if (!strncmp(this_opt, "dual", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_SDS) | LCCR0_Dual;
+ } else if (!strncmp(this_opt, "4pix", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_DPD) | LCCR0_4PixMono;
+ } else if (!strncmp(this_opt, "8pix", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_DPD) | LCCR0_8PixMono;
+ } else {
+ dev_err(dev, "unknown option: %s\n", this_opt);
+ return -EINVAL;
+ }
+ }
+ return 0;
+
+}
+
+int __init pxafb_probe(struct device *dev)
+{
+ struct pxafb_info *fbi;
+ struct pxafb_mach_info *inf;
+ int ret;
+
+ dev_dbg(dev, "pxafb_probe\n");
+
+ inf = dev->platform_data;
+ ret = -ENOMEM;
+ fbi = NULL;
+ if (!inf)
+ goto failed;
+
+ ret = pxafb_parse_options(dev, inf, g_options);
+ if ( ret < 0 )
+ goto failed;
+
+#ifdef DEBUG_VAR
+ /* Check for various illegal bit-combinations. Currently only
+ * a warning is given. */
+
+ if ( inf->lccr0 & LCCR0_INVALID_CONFIG_MASK )
+ dev_warn(dev, "machine LCCR0 setting contains illegal bits: %08x\n",
+ inf->lccr0 & LCCR0_INVALID_CONFIG_MASK);
+ if ( inf->lccr3 & LCCR3_INVALID_CONFIG_MASK )
+ dev_warn(dev, "machine LCCR3 setting contains illegal bits: %08x\n",
+ inf->lccr3 & LCCR3_INVALID_CONFIG_MASK);
+ if ( inf->lccr0 & LCCR0_DPD &&
+ ( ( inf->lccr0 & LCCR0_PAS ) != LCCR0_Pas ||
+ ( inf->lccr0 & LCCR0_SDS ) != LCCR0_Sngl ||
+ ( inf->lccr0 & LCCR0_CMS ) != LCCR0_Mono ) )
+ dev_warn(dev, "Double Pixel Data (DPD) mode is only valid in passive mono"
+ " single panel mode\n");
+ if ( (inf->lccr0 & LCCR0_PAS) == LCCR0_Act &&
+ ( inf->lccr0 & LCCR0_SDS ) == LCCR0_Dual )
+ dev_warn(dev, "Dual panel only valid in passive mode\n");
+ if ( (inf->lccr0 & LCCR0_PAS ) == LCCR0_Pas &&
+ (inf->upper_margin || inf->lower_margin) )
+ dev_warn(dev, "Upper and lower margins must be 0 in passive mode\n");
+#endif
+
+ dev_dbg(dev, "got a %dx%dx%d LCD\n",inf->xres, inf->yres, inf->bpp);
+ if (inf->xres == 0 || inf->yres == 0 || inf->bpp == 0) {
+ dev_err(dev, "Invalid resolution or bit depth\n");
+ ret = -EINVAL;
+ goto failed;
+ }
+ pxafb_backlight_power = inf->pxafb_backlight_power;
+ pxafb_lcd_power = inf->pxafb_lcd_power;
+ fbi = pxafb_init_fbinfo(inf);
+ if (!fbi) {
+ dev_err(dev, "Failed to initialize framebuffer device\n");
+ ret = -ENOMEM; // only reason for pxafb_init_fbinfo to fail is kmalloc
+ goto failed;
+ }
+
+ /* Initialize video memory */
+ ret = pxafb_map_video_memory(fbi);
+ if (ret) {
+ dev_err(dev, "Failed to allocate video RAM: %d\n", ret);
+ ret = -ENOMEM;
+ goto failed;
+ }
+ /* enable LCD controller clock */
+ CKEN |= CKEN16_LCD;
+
+ ret = request_irq(IRQ_LCD, pxafb_handle_irq, SA_INTERRUPT, "LCD", fbi);
+ if (ret) {
+ dev_err(dev, "request_irq failed: %d\n", ret);
+ ret = -EBUSY;
+ goto failed;
+ }
+
+ /*
+ * This makes sure that our colour bitfield
+ * descriptors are correctly initialised.
+ */
+ pxafb_check_var(&fbi->fb.var, &fbi->fb);
+ pxafb_set_par(&fbi->fb);
+
+ dev_set_drvdata(dev, fbi);
+
+ ret = register_framebuffer(&fbi->fb);
+ if (ret < 0) {
+ dev_err(dev, "Failed to register framebuffer device: %d\n", ret);
+ goto failed;
+ }
+
+#ifdef CONFIG_PM
+ // TODO
+#endif
+
+#ifdef CONFIG_CPU_FREQ
+ fbi->freq_transition.notifier_call = pxafb_freq_transition;
+ fbi->freq_policy.notifier_call = pxafb_freq_policy;
+ cpufreq_register_notifier(&fbi->freq_transition, CPUFREQ_TRANSITION_NOTIFIER);
+ cpufreq_register_notifier(&fbi->freq_policy, CPUFREQ_POLICY_NOTIFIER);
+#endif
+
+ /*
+ * Ok, now enable the LCD controller
+ */
+ set_ctrlr_state(fbi, C_ENABLE);
+
+ return 0;
+
+failed:
+ dev_set_drvdata(dev, NULL);
+ if (fbi)
+ kfree(fbi);
+ return ret;
+}
+
+static struct device_driver pxafb_driver = {
+ .name = "pxafb",
+ .bus = &platform_bus_type,
+ .probe = pxafb_probe,
+#ifdef CONFIG_PM
+ .suspend = pxafb_suspend,
+ .resume = pxafb_resume,
+#endif
+};
+
+int __devinit pxafb_init(void)
+{
+ return driver_register(&pxafb_driver);
+}
+
+#ifndef MODULE
+int __devinit pxafb_setup(char *options)
+{
+ long opsi = strlen(options);
+
+ memcpy(g_options, options,
+ ((opsi + 1) >
+ PXAFB_OPTIONS_SIZE) ? PXAFB_OPTIONS_SIZE : (opsi + 1));
+ g_options[PXAFB_OPTIONS_SIZE - 1] = 0;
+
+ return 0;
+}
+#else
+module_init(pxafb_init);
+module_param_string(options, g_options, sizeof(g_options), 0);
+MODULE_PARM_DESC(options, "LCD parameters (see Documentation/fb/pxafb.txt)");
+#endif
+
+
+MODULE_DESCRIPTION("loadable framebuffer driver for PXA");
+MODULE_LICENSE("GPL");
Index: linux-2.6-bkpxa/drivers/video/pxafb.h
===================================================================
--- linux-2.6-bkpxa.orig/drivers/video/pxafb.h 2004-02-16 12:43:21.000000000 +0000
+++ linux-2.6-bkpxa/drivers/video/pxafb.h 2004-03-17 09:30:50.000000000 +0000
@@ -0,0 +1,245 @@
+/*
+ * linux/drivers/video/pxafb.h
+ * -- Intel PXA250/210 LCD Controller Frame Buffer Device
+ *
+ * Copyright (C) 1999 Eric A. Thomas
+ * Based on acornfb.c Copyright (C) Russell King.
+ *
+ * 2001-08-03: Cliff Brake <cbrake@xxxxxxxxxxx>
+ * - ported SA1100 code to PXA
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive
+ * for more details.
+ */
+
+/* Shadows for LCD controller registers */
+struct pxafb_lcd_reg {
+ unsigned int lccr0;
+ unsigned int lccr1;
+ unsigned int lccr2;
+ unsigned int lccr3;
+};
+
+/* PXA LCD DMA descriptor */
+struct pxafb_dma_descriptor {
+ unsigned int fdadr;
+ unsigned int fsadr;
+ unsigned int fidr;
+ unsigned int ldcmd;
+};
+
+struct pxafb_info {
+ struct fb_info fb;
+
+ u_int max_bpp;
+ u_int max_xres;
+ u_int max_yres;
+
+ /*
+ * These are the addresses we mapped
+ * the framebuffer memory region to.
+ */
+ /* raw memory addresses */
+ dma_addr_t map_dma; /* physical */
+ u_char * map_cpu; /* virtual */
+ u_int map_size;
+
+ /* addresses of pieces placed in raw buffer */
+ u_char * screen_cpu; /* virtual address of frame buffer */
+ dma_addr_t screen_dma; /* physical address of frame buffer */
+ u16 * palette_cpu; /* virtual address of palette memory */
+ dma_addr_t palette_dma; /* physical address of palette memory */
+ u_int palette_size;
+
+ /* DMA descriptors */
+ struct pxafb_dma_descriptor * dmadesc_fblow_cpu;
+ dma_addr_t dmadesc_fblow_dma;
+ struct pxafb_dma_descriptor * dmadesc_fbhigh_cpu;
+ dma_addr_t dmadesc_fbhigh_dma;
+ struct pxafb_dma_descriptor * dmadesc_palette_cpu;
+ dma_addr_t dmadesc_palette_dma;
+
+ dma_addr_t fdadr0;
+ dma_addr_t fdadr1;
+
+ u_int lccr0;
+ u_int lccr3;
+ u_int cmap_inverse:1,
+ cmap_static:1,
+ unused:30;
+
+ u_int reg_lccr0;
+ u_int reg_lccr1;
+ u_int reg_lccr2;
+ u_int reg_lccr3;
+
+ volatile u_char state;
+ volatile u_char task_state;
+ struct semaphore ctrlr_sem;
+ wait_queue_head_t ctrlr_wait;
+ struct work_struct task;
+
+#ifdef CONFIG_PM
+ struct pm_dev *pm;
+#endif
+#ifdef CONFIG_CPU_FREQ
+ struct notifier_block freq_transition;
+ struct notifier_block freq_policy;
+#endif
+};
+
+#define __type_entry(ptr,type,member) ((type *)((char *)(ptr)-offsetof(type,member)))
+
+#define TO_INF(ptr,member) __type_entry(ptr,struct pxafb_info,member)
+
+/*
+ * These are the actions for set_ctrlr_state
+ */
+#define C_DISABLE (0)
+#define C_ENABLE (1)
+#define C_DISABLE_CLKCHANGE (2)
+#define C_ENABLE_CLKCHANGE (3)
+#define C_REENABLE (4)
+#define C_DISABLE_PM (5)
+#define C_ENABLE_PM (6)
+#define C_STARTUP (7)
+
+#define PXA_NAME "PXA"
+
+/*
+ * Debug macros
+ */
+#if DEBUG
+# define DPRINTK(fmt, args...) printk("%s: " fmt, __FUNCTION__ , ## args)
+#else
+# define DPRINTK(fmt, args...)
+#endif
+
+/*
+ * Minimum X and Y resolutions
+ */
+#define MIN_XRES 64
+#define MIN_YRES 64
+
+/*
+ * Are we configured for 8 or 16 bits per pixel?
+ */
+#ifdef CONFIG_FB_PXA_8BPP
+# define PXAFB_BPP 8
+# define PXAFB_BPP_BITS 0x03
+#elif CONFIG_FB_PXA_16BPP
+# define PXAFB_BPP 16
+# define PXAFB_BPP_BITS 0x04
+#endif
+
+#if defined(CONFIG_ARCH_LUBBOCK)
+#define LCD_PIXCLOCK 150000
+#define LCD_BPP PXAFB_BPP
+#ifdef CONFIG_FB_PXA_QVGA
+#define LCD_XRES 320
+#define LCD_YRES 240
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 51
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 1
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 1
+#define LCD_BEGIN_FRAME_WAIT_COUNT 8
+#define LCD_END_OF_LINE_WAIT_COUNT 1
+#define LCD_END_OF_FRAME_WAIT_COUNT 1
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 0x003008F8
+#define LCD_LCCR3 (0x0040FF0C | (PXAFB_BPP_BITS << 24))
+#else
+#define LCD_XRES 640
+#define LCD_YRES 480
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 1
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 1
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 3
+#define LCD_BEGIN_FRAME_WAIT_COUNT 0
+#define LCD_END_OF_LINE_WAIT_COUNT 3
+#define LCD_END_OF_FRAME_WAIT_COUNT 0
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 0x0030087C
+#define LCD_LCCR3 (0x0040FF0C | (PXAFB_BPP_BITS << 24))
+#endif
+
+#elif defined (CONFIG_ARCH_PXA_IDP)
+#define LCD_PIXCLOCK 150000
+#define LCD_BPP PXAFB_BPP
+#define LCD_XRES 640
+#define LCD_YRES 480
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 1
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 1
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 3
+#define LCD_BEGIN_FRAME_WAIT_COUNT 0
+#define LCD_END_OF_LINE_WAIT_COUNT 3
+#define LCD_END_OF_FRAME_WAIT_COUNT 0
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 0x0030087C
+#define LCD_LCCR3 (0x0040FF0C | (PXAFB_BPP_BITS << 24))
+
+#elif defined CONFIG_PXA_CERF_PDA
+#define LCD_PIXCLOCK 171521
+#define LCD_BPP PXAFB_BPP
+#define LCD_XRES 240
+#define LCD_YRES 320
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 7
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 2
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 17
+#define LCD_BEGIN_FRAME_WAIT_COUNT 0
+#define LCD_END_OF_LINE_WAIT_COUNT 17
+#define LCD_END_OF_FRAME_WAIT_COUNT 0
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 (LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_QDM | LCCR0_BM | LCCR0_OUM)
+#define LCD_LCCR3 (LCCR3_PCP | LCCR3_PixClkDiv(0x12) | LCCR3_Bpp(PXAFB_BPP_BITS) | LCCR3_Acb(0x18))
+
+#elif defined CONFIG_ARCH_RAMSES
+#define LCD_PIXCLOCK 150000
+#define LCD_BPP PXAFB_BPP
+#define LCD_XRES 240
+#define LCD_YRES 320
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 1
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 1
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 1
+#define LCD_BEGIN_FRAME_WAIT_COUNT 7
+#define LCD_END_OF_LINE_WAIT_COUNT 1
+#define LCD_END_OF_FRAME_WAIT_COUNT 1
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 (LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_QDM | LCCR0_BM | LCCR0_OUM)
+#define LCD_LCCR3 (LCCR3_PCP | LCCR3_Bpp(PXAFB_BPP_BITS) | LCCR3_Acb(0xe))
+
+#elif defined CONFIG_ARCH_RAMSES
+#define LCD_PIXCLOCK 150000
+#define LCD_BPP PXAFB_BPP
+#define LCD_XRES 240
+#define LCD_YRES 320
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 1
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 1
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 1
+#define LCD_BEGIN_FRAME_WAIT_COUNT 7
+#define LCD_END_OF_LINE_WAIT_COUNT 1
+#define LCD_END_OF_FRAME_WAIT_COUNT 1
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 (LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_QDM | LCCR0_BM | LCCR0_OUM)
+#define LCD_LCCR3 (LCCR3_PCP | LCCR3_Bpp(PXAFB_BPP_BITS) | LCCR3_Acb(0xe))
+
+#elif defined CONFIG_ARCH_LOOX600
+#ifdef CONFIG_FB_PXA_8BPP
+#error "8BPP Not supported!"
+#endif
+
+#elif defined(CONFIG_ARCH_ADSBITSYX) || defined(CONFIG_ARCH_ADSAGX)
+#define LCD_PIXCLOCK 40188
+#define LCD_BPP PXAFB_BPP
+#define LCD_XRES 640
+#define LCD_YRES 480
+#define LCD_HORIZONTAL_SYNC_PULSE_WIDTH 4
+#define LCD_VERTICAL_SYNC_PULSE_WIDTH 9
+#define LCD_BEGIN_OF_LINE_WAIT_COUNT 16
+#define LCD_BEGIN_FRAME_WAIT_COUNT 25
+#define LCD_END_OF_LINE_WAIT_COUNT 15
+#define LCD_END_OF_FRAME_WAIT_COUNT 33
+#define LCD_SYNC (FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT)
+#define LCD_LCCR0 ((0x01 << 12) | LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS | LCCR0_QDM | LCCR0_BM | LCCR0_OUM) // Single Active Color
+#define LCD_LCCR3 (LCCR3_Bpp(PXAFB_BPP_BITS) | LCCR3_HSP | LCCR3_VSP | LCCR3_PixClkDiv(0x01))
+
+#endif
Index: linux-2.6-bkpxa/include/asm-arm/arch-pxa/pxa-regs.h
===================================================================
--- linux-2.6-bkpxa.orig/include/asm-arm/arch-pxa/pxa-regs.h 2004-03-17 09:30:50.000000000 +0000
+++ linux-2.6-bkpxa/include/asm-arm/arch-pxa/pxa-regs.h 2004-03-17 09:30:50.000000000 +0000
@@ -1291,15 +1291,27 @@
#define LDCMD1 __REG(0x4400021C) /* DMA Channel 1 Command Register */
#define LCCR0_ENB (1 << 0) /* LCD Controller enable */
-#define LCCR0_CMS (1 << 1) /* Color = 0, Monochrome = 1 */
-#define LCCR0_SDS (1 << 2) /* Single Panel = 0, Dual Panel = 1 */
+#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */
+#define LCCR0_Color (LCCR0_CMS*0) /* Color display */
+#define LCCR0_Mono (LCCR0_CMS*1) /* Monochrome display */
+#define LCCR0_SDS (1 << 2) /* Single/Dual Panel Display */
+ /* Select */
+#define LCCR0_Sngl (LCCR0_SDS*0) /* Single panel display */
+#define LCCR0_Dual (LCCR0_SDS*1) /* Dual panel display */
+
#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */
#define LCCR0_SFM (1 << 4) /* Start of frame mask */
#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */
#define LCCR0_EFM (1 << 6) /* End of Frame mask */
-#define LCCR0_PAS (1 << 7) /* Passive = 0, Active = 1 */
-#define LCCR0_BLE (1 << 8) /* Little Endian = 0, Big Endian = 1 */
-#define LCCR0_DPD (1 << 9) /* Double Pixel mode, 4 pixel value = 0, 8 pixle values = 1 */
+#define LCCR0_PAS (1 << 7) /* Passive/Active display Select */
+#define LCCR0_Pas (LCCR0_PAS*0) /* Passive display (STN) */
+#define LCCR0_Act (LCCR0_PAS*1) /* Active display (TFT) */
+#define LCCR0_DPD (1 << 9) /* Double Pixel Data (monochrome */
+ /* display mode) */
+#define LCCR0_4PixMono (LCCR0_DPD*0) /* 4-Pixel/clock Monochrome */
+ /* display */
+#define LCCR0_8PixMono (LCCR0_DPD*1) /* 8-Pixel/clock Monochrome */
+ /* display */
#define LCCR0_DIS (1 << 10) /* LCD Disable */
#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */
#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */
@@ -1361,8 +1373,15 @@
#define LCCR3_API_S 16
#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
-#define LCCR3_PCP (1 << 22) /* pixel clock polarity */
-#define LCCR3_OEP (1 << 23) /* output enable polarity */
+#define LCCR3_PCP (1 << 22) /* Pixel Clock Polarity (L_PCLK) */
+#define LCCR3_PixRsEdg (LCCR3_PCP*0) /* Pixel clock Rising-Edge */
+#define LCCR3_PixFlEdg (LCCR3_PCP*1) /* Pixel clock Falling-Edge */
+
+#define LCCR3_OEP (1 << 23) /* Output Enable Polarity (L_BIAS, */
+ /* active display mode) */
+#define LCCR3_OutEnH (LCCR3_OEP*0) /* Output Enable active High */
+#define LCCR3_OutEnL (LCCR3_OEP*1) /* Output Enable active Low */
+
#if 0
#define LCCR3_BPP (7 << 24) /* bits per pixel */
#define LCCR3_BPP_S 24
Index: linux-2.6-bkpxa/include/asm-arm/arch-pxa/pxafb.h
===================================================================
--- linux-2.6-bkpxa.orig/include/asm-arm/arch-pxa/pxafb.h 2004-02-16 12:43:21.000000000 +0000
+++ linux-2.6-bkpxa/include/asm-arm/arch-pxa/pxafb.h 2004-03-17 09:30:50.000000000 +0000
@@ -0,0 +1,68 @@
+/*
+ * linux/include/asm-arm/arch-pxa/pxafb.h
+ *
+ * Support for the xscale frame buffer.
+ *
+ * Author: Jean-Frederic Clere
+ * Created: Sep 22, 2003
+ * Copyright: jfclere@xxxxxxxxx
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * This structure describes the machine which we are running on.
+ * It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine
+ * of linux/drivers/video/pxafb.c
+ */
+struct pxafb_mach_info {
+ u_long pixclock;
+
+ u_short xres;
+ u_short yres;
+
+ u_char bpp;
+ u_char hsync_len;
+ u_char left_margin;
+ u_char right_margin;
+
+ u_char vsync_len;
+ u_char upper_margin;
+ u_char lower_margin;
+ u_char sync;
+
+ u_int cmap_greyscale:1,
+ cmap_inverse:1,
+ cmap_static:1,
+ unused:29;
+
+ /* The following should be defined in LCCR0
+ * LCCR0_Act or LCCR0_Pas Active or Passive
+ * LCCR0_Sngl or LCCR0_Dual Single/Dual panel
+ * LCCR0_Mono or LCCR0_Color Mono/Color
+ * LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode)
+ * LCCR0_DMADel(Tcpu) (optional) DMA request delay
+ *
+ * The following should not be defined in LCCR0:
+ * LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM
+ * LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB
+ */
+ u_int lccr0;
+ /* The following should be defined in LCCR3
+ * LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity
+ * LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type
+ * LCCR3_Acb(X) AB Bias pin frequency
+ * LCCR3_DPC (optional) Double Pixel Clock mode (untested)
+ *
+ * The following should not be defined in LCCR3
+ * LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp
+ */
+ u_int lccr3;
+
+ void (*pxafb_backlight_power)(int);
+ void (*pxafb_lcd_power)(int);
+
+};
+void set_pxa_fb_info(struct pxafb_mach_info *hard_pxa_fb_info);
Cheers,
Ian.
--
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/