Re: ide taskfile and cdrom hang

[Mark Haverkamp]

On Mon, 2004-02-02 at 16:13, Bartlomiej Zolnierkiewicz wrote:
> On Tuesday 03 of February 2004 00:52, Mark Haverkamp wrote:
> > On Mon, 2004-02-02 at 15:37, Bartlomiej Zolnierkiewicz wrote:
> > > On Monday 02 of February 2004 22:44, Mark Haverkamp wrote:
> > > > On Mon, 2004-02-02 at 13:35, Bartlomiej Zolnierkiewicz wrote:
> > > > > On Monday 02 of February 2004 21:45, Mark Haverkamp wrote:
> > > > > > On Mon, 2004-02-02 at 11:45, Bartlomiej Zolnierkiewicz wrote:
> > > > > > > On Monday 02 of February 2004 19:46, Mark Haverkamp wrote:
> > > > > > > > On Sun, 2004-02-01 at 12:48, Bartlomiej Zolnierkiewicz wrote:
> >
> > [ ... ]
> >
> > > Now, can you comment out "(UDELAY(10))" printk and add printk for
> > > "retries" variable after while {} loop.  I thought there will be more
> > > "(UDELAY(10))" messages - but I forgot about delay introduced by printk()
> > > call :-).
> > >
> > > --bart
> >
> > I ran twice, got the same results:
> >
> > 1)
> > hda: (WAIT_NOT_BUSY) status=0x50 retry 94
> > hda: (CHECK_STATUS) status=0x50
> > hda: (WAIT_NOT_BUSY) status=0x50 retry 94
> > hda: (CHECK_STATUS) status=0x50
> 
> Is this output for single 'cat /proc/ide/hda/identify' run?
> There should be only one WAIT_NOT_BUSY and one CHECK_STATUS.

I see two for each cat.  Also, the 94 is the leftover number. So there
were probably about 6 retries.
> 
> > 2)
> > hda: (WAIT_NOT_BUSY) status=0x50 retry 94
> > hda: (CHECK_STATUS) status=0x50
> > hda: (WAIT_NOT_BUSY) status=0x50 retry 94
> > hda: (CHECK_STATUS) status=0x50
> 
> Wow, 94 retries vs. limit of 5 previously.

The 94 is the leftover number. Retry started at 100 and was decremented
in the status check loop. So there were probably about 6 retries.


> 
> Please also check if  'hdparm -Istdin</proc/ide/hda/identify'
> returns correct information now.

# hdparm  -Istdin</proc/ide/hda/identify
 
ATAPI CD-ROM, with removable media
        Model Number:       CD-224E
        Serial Number:
        Firmware Revision:  1.5A
Standards:
        Likely used CD-ROM ATAPI-1
Configuration:
        DRQ response: 50us.
        Packet size: 12 bytes
Capabilities:
        Cmd overlap, LBA, IORDY(can be disabled)
        Buffer size: 128.0kB
        Overlap support: 896us to release bus. 115us to clear BSY after SERVICE
cmd.
        DMA: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns


Plus:

hda: (WAIT_NOT_BUSY) status=0x50 retry 94
hda: (CHECK_STATUS) status=0x50

on the console.


> 
> Thanks,
> --bart

I see two for each cat.  Also, the 94 is the leftover number. So there
were probably about 6 retries.

Mark.
-- 
Mark Haverkamp <markh@xxxxxxxx>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/