Re: EISA ID for PnP modem and resource allocation
From: Amit Gurdasani
Date: Thu Jan 29 2004 - 01:56:24 EST
On Mon, 26 Jan 2004, Adam Belay wrote:
:On Mon, Jan 05, 2004 at 05:23:27PM +0400, Amit Gurdasani wrote:
:> On Sun, 4 Jan 2004, Russell King wrote:
:>
:> :On Mon, Dec 29, 2003 at 10:50:37PM +0000, Adam Belay wrote:
:> :> > ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
:> :> > ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
:> :> > ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
:> :> > parport0: irq 7 detected
:> :>
:> :> Hmm, it shouldn't be reporting irq 0. The probbing code may be confused.
:> :> I would guess it is on irq 4.
:> :
:> :irq0 on x86 means "I'll use polled mode".
:
:It occured to me that we should probably check which resources the pnpbios is
:reporting. If you have a chance, could you please show me the output of this
:hack.
Sorry about taking so long to reply.
It doesn't seem that the printk was ever called. Here are dmesg outputs with
and without isapnptools capturing an IRQ for the ISA modem. (I'm using
loadlin from DOS to boot Linux, incidentally. Would that make any
difference?)
Without userspace isapnp, the modem isn't picked up by the serial driver:
Linux version 2.6.1 (amitg@xxxxxxxxxxxxxxxxxx) (gcc version 3.3.2 20030908 (Debian prerelease)) #2 Thu Jan 29 01:18:51 GST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
128MB LOWMEM available.
On node 0 totalpages: 32768
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28672 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
Building zonelist for node : 0
Kernel command line: root=/dev/hdf1 pnp_reserve_irq=5 BOOT_IMAGE=vmlinu~1
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 398.946 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x60
Memory: 126888k/131072k available (1352k kernel code, 3628k reserved, 642k data, 132k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 788.48 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000
Enabling new style K6 write allocation for 128 Mb
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb1a0, last bus=0
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: the driver 'system' has been registered
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd20
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbd48, dseg 0xf0000
pnp: match found with the PnP device '00:07' and the driver 'system'
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: 00:0a: ioport range 0x208-0x20f has been reserved
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7000] at 0000:00:07.0
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
devfs: v1.22 (20021013) Richard Gooch (rgooch@xxxxxxxxxxxxx)
devfs: boot_options: 0x1
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: Card 'ISA PnP K56flex Fax/Modem'
isapnp: 1 Plug & Play card detected total
pty: 2048 Unix98 ptys configured
Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 0000:00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hdc: ATAPI CDROM 48X, ATAPI CD/DVD-ROM drive
hdd: CD-ROM 24X/AKOx, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
SiI680: IDE controller at PCI slot 0000:00:13.0
PCI: Found IRQ 9 for device 0000:00:13.0
SiI680: chipset revision 2
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 9
ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
hde: WDC AC34300L, ATA DISK drive
hdf: MAXTOR 6L080L4, ATA DISK drive
ide2 at 0xc8800080-0xc8800087,0xc880008a on irq 9
pnp: the driver 'ide' has been registered
hde: max request size: 64KiB
hde: 8406720 sectors (4304 MB) w/256KiB Cache, CHS=8896/15/63, UDMA(33)
/dev/ide/host2/bus0/target0/lun0: p1
hdf: max request size: 64KiB
hdf: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
/dev/ide/host2/bus0/target1/lun0: p1 p2
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
BIOS EDD facility v0.10 2003-Oct-11, 3 devices found
Please report your BIOS at http://domsch.com/linux/edd30/results.html
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Adding 302392k swap on /dev/hdf2. Priority:-1 extents:1
EXT3 FS on hdf1, internal journal
SCSI subsystem initialized
PCI: Found IRQ 11 for device 0000:00:11.0
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
i91u: PCI Base=0x6100, IRQ=11, BIOS=0xC8000, SCSI ID=7
i91u: Reset SCSI Bus ...
ERROR: SCSI host `INI9100U' has no error handling
ERROR: This is not a safe way to run your SCSI host
ERROR: The error handling must be added to this driver
Call Trace:
[<c883eede>] scsi_host_alloc+0x67/0x262 [scsi_mod]
[<c0120515>] __request_region+0x61/0x99
[<c883f0e9>] scsi_register+0x10/0x51 [scsi_mod]
[<c884e348>] i91u_detect+0x19e/0x33d [initio]
[<c882a050>] init_this_scsi_driver+0x50/0xe0 [initio]
[<c012eb41>] sys_init_module+0xe3/0x1d1
[<c0109ec7>] syscall_call+0x7/0xb
scsi0 : Initio INI-9X00U/UW SCSI device driver; Revision: 1.03g
Vendor: IBM Model: DDYS-T36950M Rev: SC4D
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.12
hdd: ATAPI 24X CD-ROM drive, 120kB Cache, DMA
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 0000:00:12.0
eth0: RealTek RTL8139 at 0xc8868000, 00:0a:cd:05:6f:66, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ip_tables: (C) 2000-2002 Netfilter core team
ppdev: user-space parallel port driver
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
inserting floppy driver for 2.6.1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Real Time Clock Driver v1.12
request_module: failed /sbin/modprobe -- nls_utf-8. error = 256
Unable to load NLS charset utf-8
request_module: failed /sbin/modprobe -- nls_utf-8. error = 256
Unable to load NLS charset utf-8
eth0: link down
With userspace isapnp enabling the ISA modem, the first serial port uses
polled mode:
Linux version 2.6.1 (amitg@xxxxxxxxxxxxxxxxxx) (gcc version 3.3.2 20030908 (Debian prerelease)) #2 Thu Jan 29 01:18:51 GST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
128MB LOWMEM available.
On node 0 totalpages: 32768
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28672 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
Building zonelist for node : 0
Kernel command line: root=/dev/hdf1 pnp_reserve_irq=5 BOOT_IMAGE=vmlinu~1
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 398.978 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x60
Memory: 126888k/131072k available (1352k kernel code, 3628k reserved, 642k data, 132k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 788.48 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000
Enabling new style K6 write allocation for 128 Mb
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb1a0, last bus=0
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: the driver 'system' has been registered
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbd20
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbd48, dseg 0xf0000
pnp: match found with the PnP device '00:07' and the driver 'system'
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: 00:0a: ioport range 0x208-0x20f has been reserved
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7000] at 0000:00:07.0
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
devfs: v1.22 (20021013) Richard Gooch (rgooch@xxxxxxxxxxxxx)
devfs: boot_options: 0x1
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: Card 'ISA PnP K56flex Fax/Modem'
isapnp: 1 Plug & Play card detected total
pty: 2048 Unix98 ptys configured
Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 0000:00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hdc: ATAPI CDROM 48X, ATAPI CD/DVD-ROM drive
hdd: CD-ROM 24X/AKOx, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
SiI680: IDE controller at PCI slot 0000:00:13.0
PCI: Found IRQ 9 for device 0000:00:13.0
SiI680: chipset revision 2
SiI680: BASE CLOCK == 133
SiI680: 100% native mode on irq 9
ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
hde: WDC AC34300L, ATA DISK drive
hdf: MAXTOR 6L080L4, ATA DISK drive
ide2 at 0xc8800080-0xc8800087,0xc880008a on irq 9
pnp: the driver 'ide' has been registered
hde: max request size: 64KiB
hde: 8406720 sectors (4304 MB) w/256KiB Cache, CHS=8896/15/63, UDMA(33)
/dev/ide/host2/bus0/target0/lun0: p1
hdf: max request size: 64KiB
hdf: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
/dev/ide/host2/bus0/target1/lun0: p1 p2
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
BIOS EDD facility v0.10 2003-Oct-11, 2 devices found
Please report your BIOS at http://domsch.com/linux/edd30/results.html
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Adding 302392k swap on /dev/hdf2. Priority:-1 extents:1
EXT3 FS on hdf1, internal journal
SCSI subsystem initialized
PCI: Found IRQ 11 for device 0000:00:11.0
i91u: PCI Base=0x6100, IRQ=11, BIOS=0xC8000, SCSI ID=7
i91u: Reset SCSI Bus ...
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
ERROR: SCSI host `INI9100U' has no error handling
ERROR: This is not a safe way to run your SCSI host
ERROR: The error handling must be added to this driver
Call Trace:
[<c883eede>] scsi_host_alloc+0x67/0x262 [scsi_mod]
[<c0120515>] __request_region+0x61/0x99
[<c883f0e9>] scsi_register+0x10/0x51 [scsi_mod]
[<c884e348>] i91u_detect+0x19e/0x33d [initio]
[<c882a050>] init_this_scsi_driver+0x50/0xe0 [initio]
[<c012eb41>] sys_init_module+0xe3/0x1d1
[<c0109ec7>] syscall_call+0x7/0xb
scsi0 : Initio INI-9X00U/UW SCSI device driver; Revision: 1.03g
Vendor: IBM Model: DDYS-T36950M Rev: SC4D
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.12
hdd: ATAPI 24X CD-ROM drive, 120kB Cache, DMA
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 0000:00:12.0
eth0: RealTek RTL8139 at 0xc8868000, 00:0a:cd:05:6f:66, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
ip_tables: (C) 2000-2002 Netfilter core team
ppdev: user-space parallel port driver
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
inserting floppy driver for 2.6.1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Real Time Clock Driver v1.12
request_module: failed /sbin/modprobe -- nls_utf-8. error = 256
Unable to load NLS charset utf-8
request_module: failed /sbin/modprobe -- nls_utf-8. error = 256
Unable to load NLS charset utf-8
eth0: link down
And for completeness' sake, here's my kernel .config:
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_EXPERIMENTAL=y
CONFIG_STANDALONE=y
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_KMOD=y
CONFIG_X86_PC=y
CONFIG_MK6=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_ALIGNMENT_16=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_PREEMPT=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_EDD=y
CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PM=y
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_APM=y
CONFIG_APM_DO_ENABLE=y
CONFIG_APM_CPU_IDLE=y
CONFIG_APM_DISPLAY_BLANK=y
CONFIG_APM_ALLOW_INTS=y
CONFIG_APM_REAL_MODE_POWER_OFF=y
CONFIG_PCI=y
CONFIG_PCI_GOBIOS=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_USE_VECTOR=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_HOTPLUG=y
CONFIG_PCMCIA_PROBE=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
CONFIG_FW_LOADER=m
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
CONFIG_PARPORT_1284=y
CONFIG_PNP=y
CONFIG_PNP_DEBUG=y
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_LBD=y
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_IDEDISK_STROKE=y
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
CONFIG_IDE_TASKFILE_IO=y
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_VIA82CXXX=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y
CONFIG_BLK_DEV_SD=m
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_REPORT_LUNS=y
CONFIG_SCSI_BUSLOGIC=m
CONFIG_SCSI_OMIT_FLASHPOINT=y
CONFIG_SCSI_INITIO=m
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_NAT=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_TOS=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
CONFIG_SYN_COOKIES=y
CONFIG_BRIDGE=m
CONFIG_NETFILTER=y
CONFIG_BRIDGE_NETFILTER=y
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_COMPAT_IPFWADM=m
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_IPV6_SCTP__=y
CONFIG_VLAN_8021Q=m
CONFIG_LLC=m
CONFIG_LLC2=m
CONFIG_IPX=m
CONFIG_ATALK=m
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_CSZ=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_CLS_POLICE=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_ETHERTAP=m
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_NE2K_PCI=m
CONFIG_8139TOO=m
CONFIG_8139TOO_TUNE_TWISTER=y
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
CONFIG_SHAPER=m
CONFIG_INPUT=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_EVDEV=m
CONFIG_GAMEPORT=m
CONFIG_SOUND_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_UINPUT=m
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_CORE=m
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=2048
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
CONFIG_I2C=m
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ISA=m
CONFIG_I2C_SENSOR=m
CONFIG_SENSORS_EEPROM=m
CONFIG_WATCHDOG=y
CONFIG_SOFT_WATCHDOG=y
CONFIG_NVRAM=m
CONFIG_RTC=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HANGCHECK_TIMER=m
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_FB=y
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_PCI_CONSOLE=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=m
CONFIG_SND=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
CONFIG_SND_AD1848=m
CONFIG_SND_OPTI92X_AD1848=m
CONFIG_SND_SB16=m
CONFIG_SND_SB16_CSP=y
CONFIG_SOUND_PRIME=m
CONFIG_SOUND_OSS=m
CONFIG_SOUND_TRACEINIT=y
CONFIG_SOUND_DMAP=y
CONFIG_SOUND_VMIDI=m
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
CONFIG_SOUND_MAD16=m
CONFIG_MAD16_OLDCARD=y
CONFIG_SOUND_SB=m
CONFIG_USB=m
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_AUDIO=m
CONFIG_USB_MIDI=m
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_GENESYS=y
CONFIG_USB_NET1080=y
CONFIG_USB_PL2301=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_ZAURUS=y
CONFIG_USB_CDCETHER=y
CONFIG_USB_AX8817X=y
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
CONFIG_REISERFS_PROC_INFO=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_RT=y
CONFIG_XFS_QUOTA=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_AUTOFS4_FS=m
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=m
CONFIG_NTFS_FS=m
CONFIG_NTFS_RW=y
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
CONFIG_DEVPTS_FS=y
CONFIG_DEVPTS_FS_XATTR=y
CONFIG_DEVPTS_FS_SECURITY=y
CONFIG_TMPFS=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
CONFIG_HFS_FS=m
CONFIG_BEFS_FS=m
CONFIG_CRAMFS=m
CONFIG_VXFS_FS=m
CONFIG_QNX4FS_FS=m
CONFIG_QNX4FS_RW=y
CONFIG_UFS_FS=m
CONFIG_UFS_FS_WRITE=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="utf-8"
CONFIG_CIFS=m
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_AFS_FS=m
CONFIG_RXRPC=m
CONFIG_PARTITION_ADVANCED=y
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
CONFIG_SUN_PARTITION=y
CONFIG_EFI_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf-8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_UTF8=m
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_X86_EXTRA_IRQS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_CAPABILITIES=m
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_X86_BIOS_REBOOT=y
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/