On Mon, 2003-08-04 at 15:36, Justin T. Gibbs wrote:
> > Patrick,
> >
> > I enabled CONFIG_SCSI_LOGGING=y in kernel then i used
> > scsi_mod.scsi_logging_level=0x140 and scsi_mod.max_scsi_luns=1 when
> > booting the kernel from lilo.I can see some debug information scroll on
> > the screen and i did see ID0 LUN0 get probed even the correct transfer
> > rate for the SCSI disk is set.I forgot but isn't there a key sequence
> > when pressed it will stop the screen output like pause/break key?
>
> You might be able to get useful information without using a serial
> console if you turn off your CDROM drives so they don't add extra output,
> but your best bet is to use a serial console.
>
> --
> Justin
>
>
Hi Justin,
This time with both plextor cdroms removed i get this in console:
scsi scan: INQUIRY to host 0 chanel 0 id0 lun 0
scsi scan: 1st INQUIRY failed with code 0x10000
and this repeats for all 15 id's on the cards with same 0x10000 code.
When using aic7xxx_old driver i get this in dmesg:
(scsi0) <Adaptec AHA-294X Ultra2 SCSI host adapter> found at PCI 1/10/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 398 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.6/5.2.0
<Adaptec AHA-294X Ultra2 SCSI host adapter>
scsi scan: INQUIRY to host 0 channel 0 id 0 lun 0
scsi scan: 1st INQUIRY successful with code 0x0
Vendor: Model: Rev:
Type: Direct-Access ANSI SCSI revision: 00
scsi scan: Sequential scan of host 0 channel 0 id 0
scsi scan: INQUIRY to host 0 channel 0 id 1 lun 0
scsi: Device offlined - not ready after error recovery: host 0 channel 0
id 1 lun 0
scsi scan: 1st INQUIRY failed with code 0x6030000
scsi scan: INQUIRY to host 0 channel 0 id 2 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 3 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 4 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 5 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 6 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 8 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 9 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 10 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 11 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 12 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 13 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 14 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
scsi scan: INQUIRY to host 0 channel 0 id 15 lun 0
scsi scan: 1st INQUIRY failed with code 0x30000
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Once i get null modem serial cable i will try to get more info from
serial console.
Regards,
Paul
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu Aug 07 2003 - 22:00:27 EST