amd74xx.c in 2.4.21-pre4-ac4 uses an uninitialized variable to set the
cable type. I have made a simple fix that I have tried it with an MSI
K7N2G-ILSR nForce2 board. With this patch the 80 wire cable on my
primary IDE is detected by the workaround, but the secondary IDE is
still incorrectly reported as 40 wire, so something may still be
wrong. See below some IDE boot messages and the small patch.
I am not subscribed to the list, so please CC me any reply. The
return e-mail address is temporary to prevent spam, if the mail
bounces, resend it to hzoli instead of amd_80w.
Zoli
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
AMD_IDE: Bios didn't set cable bits corectly. Enabling workaround.
AMD_IDE: PCI device 10de:0065 (nVidia Corporation) (rev a2) UDMA100 controller o
n pci00:09.0
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD1200JB-75CRA0, ATA DISK drive
hdc: RIDATA DVD+RW DRIVE, ATAPI CD/DVD-ROM drive
----------AMD BusMastering IDE Configuration----------------
Driver Version: 2.9
South Bridge: PCI device 10de:0065 (nVidia Corporation)
Revision: IDE 0xa2
Highest DMA rate: UDMA100
BM-DMA base: 0xf000
PCI clock: 33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA DMA UDMA DMA
Address Setup: 30ns 90ns 30ns 90ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 30ns 270ns
Cycle Time: 20ns 600ns 60ns 600ns
Transfer Rate: 99.9MB/s 3.3MB/s 33.3MB/s 3.3MB/s
--- drivers/ide/pci/amd74xx.c~ Fri Feb 14 10:22:25 2003
+++ drivers/ide/pci/amd74xx.c Tue Feb 25 11:31:53 2003
@@ -309,7 +309,8 @@
case AMD_UDMA_100:
pci_read_config_byte(dev, AMD_CABLE_DETECT, &t);
- amd_80w = ((u & 0x3) ? 1 : 0) | ((u & 0xc) ? 2 : 0);
+ amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0);
+ pci_read_config_dword(dev, AMD_UDMA_TIMING, &u);
for (i = 24; i >= 0; i -= 8)
if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) {
printk(KERN_WARNING "AMD_IDE: Bios didn't set cable bits corectly. Enabling workaround.\n");
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Feb 28 2003 - 22:00:30 EST