Problem: My xwindows did not open and my sound card don't work.
Xwindows:
I am a novice. I am using redhat linux 8. It detects my graphics
card
correctly but when i tried to open xwindows, my system hangs.
Sound:
Linux has detected my sound card once but not configured it and
after
that nor it is working nither it is detected by my linux.
GRUB:
Also, i can boot my linux through LILO only. GRUB wont work, it
gives
error "Not enough memory".
I have re-installed linux on my computer but the problem
remains.
All other detailes are follows.
Kernel version:
Linux version 2.4.18-14 (bhcompile@astest.test.redhat.com)
(gcc version 3.2 20020903 (Red Hat Linux 8.0 3.2-7))
#1 Wed Sep 4 12:13:11 EDT 2002
Commond which triggers the problem:
startx
Processor information:
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(TM) XP 1700+
stepping : 2
cpu MHz : 1469.861
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 2920.57
Module information:
nls_iso8859-1 3516 1 (autoclean)
nls_cp437 5116 1 (autoclean)
vfat 13084 1 (autoclean)
fat 38744 0 (autoclean)
[vfat]
autofs 13348 0 (autoclean) (unused)
ipt_REJECT 3736 2 (autoclean)
iptable_filter 2412 1 (autoclean)
ip_tables 14840 2 [ipt_REJECT iptable_filter]
mousedev 5524 0 (unused)
keybdev 2976 0 (unused)
hid 22244 0 (unused)
input 5888 0 [mousedev keybdev hid]
usb-ohci 21288 0 (unused)
usbcore 77056 1 [hid usb-ohci]
ext3 70400 1
jbd 52212 1 [ext3]
Loaded driver and hardware information:
0000-001f : dma
1
0020-003f : pic
1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic
2
00c0-00df : dma
2
00f0-00ff : fpu
01f0-01f7 : ide
0
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide
0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf
1
5000-500f : PCI device 10de:01b4 (nVidia Corporation)
5100-511f : PCI device 10de:01b4 (nVidia Corporation)
5500-550f : PCI device 10de:01b4 (nVidia Corporation)
a800-a80f : nVidia Corporation nForce IDE
a800-a807 : ide0
a808-a80f : ide1
b000-bfff : PCI Bus #01
b800-b807 : Rockwell International HCF 56k Data/Fax/Voice/Spkp
(w/Handset) Modem
d800-d807 : PCI device 10de:01c3 (nVidia Corporation)
e000-e07f : PCI device 10de:01b1 (nVidia Corporation)
e100-e1ff : PCI device 10de:01b1 (nVidia Corporation)
00000000-0007ffff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-06febfff : System RAM
00100000-00247f2e : Kernel code
00247f2f-0033ed03 : Kernel data
06fec000-06feefff : ACPI Tables
06fef000-06ffefff : reserved
06fff000-06ffffff : ACPI Non-volatile Storage
eb000000-ec7fffff : PCI Bus #02
eb000000-ebffffff : nVidia Corporation GeForce2 Integrated GPU
ec800000-ecffffff : PCI Bus #01
ec800000-ec80ffff : Rockwell International HCF 56k
Data/Fax/Voice/Spkp (w/Handset) Modem
ed000000-ed000fff : PCI device 10de:01b1 (nVidia Corporation)
ed800000-ed87ffff : PCI device 10de:01b0 (nVidia Corporation)
ee000000-ee0003ff : PCI device 10de:01c3 (nVidia Corporation)
ee800000-ee800fff : PCI device 10de:01c2 (nVidia Corporation)
ee800000-ee800fff : usb-ohci
e
f000000-ef000fff : PCI device
10de:01c2 (nVidia Corporation)
ef000000-ef000fff : usb-ohci
e
ff00000-f7ffffff : PCI Bus #02
f0000000-f7ffffff : nVidia Corporation GeForce2 Integrated GPU
f8000000-fbffffff : PCI device
10de:01a4 (nVidia Corporation)
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
PCI information:
00:00.0 Host bridge: nVidia Corporation nForce CPU bridge (rev
b2)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [40] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x1
Capabilities: [60] #08 [2001]
00:00.1 RAM memory: nVidia Corporation nForce 220/420 Memory
Controller (rev b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: nVidia Corporation nForce 220/420 Memory
Controller (rev b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation: Unknown device 01aa (rev
b2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:01.0 ISA bridge: nVidia Corporation nForce ISA Bridge (rev
c3)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [50] #08 [01e1]
00:01.1 SMBus: nVidia Corporation nForce PCI System Management
(rev c1)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 5000 [size=16]
Region 1: I/O ports at 5500 [size=16]
Region 2: I/O ports at 5100 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation: Unknown device 01c2
(rev c3) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ef000000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: nVidia Corporation: Unknown device 01c2
(rev c3) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ee800000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: nVidia Corporation: Unknown device
01c3 (rev c2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ee000000 (32-bit, non-prefetchable)
[size=1K]
Region 1: I/O ports at d800 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: nVidia Corporation: Unknown
device 01b0 (rev c2)
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ed800000 (32-bit, non-prefetchable)
[size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce
Audio (rev c2)
Subsystem: nVidia Corporation: Unknown device 8384
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e100 [size=256]
Region 1: I/O ports at e000 [size=128]
Region 2: Memory at ed000000 (32-bit, non-prefetchable)
[disabled] [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 PCI bridge: nVidia Corporation nForce PCI-to-PCI bridge
(rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ec800000-ecffffff
Prefetchable memory behind bridge: f8000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:09.0 IDE interface: nVidia Corporation nForce IDE (rev c3)
(prog-if 8a [Master SecP PriP])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at a800 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: nVidia Corporation nForce AGP to PCI Bridge
(rev b2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000a000-00009fff
Memory behind bridge: eb000000-ec7fffff
Prefetchable memory behind bridge: eff00000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
01:08.0 Communication controller: Rockwell International HCF 56k
Data/Fax/Voice/Spkp (w/Handset) Modem (rev 01)
Subsystem: Rockwell International HCF 56k Data/Fax/Voice/Spkp
(w/Handset) Modem
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ec800000 (32-bit, non-prefetchable)
[size=64K]
Region 1: I/O ports at b800 [size=8]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
02:00.0 VGA compatible controller: nVidia Corporation NV15
[GeForce2 - nForce GPU] (rev b1) (prog-if 00 [VGA])
Subsystem: nVidia Corporation: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at eb000000 (32-bit, non-prefetchable)
[size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable)
[size=128M]
Expansion ROM at efff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
XF86Config:
# File generated by anaconda.
Section "ServerLayout"
Identifier "Anaconda Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Mouse1" "SendCoreEvents"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of
the
# file minus the extension (like ".txt" or ".db"). There is
normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated
together)
# By default, Red Hat 6.0 and later now use a font server
independent of
# the X server to render fonts.
FontPath "unix/:7100"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "dri"
Load "glx"
Load "record"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
# Option "AutoRepeat" "500 5"
# when using XQUEUE, comment out the above line, and uncomment
the
# following line
# Option "Protocol" "Xqueue"
# Specify which keyboard LEDs can be user-controlled (eg, with
xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify
the
# lines below (which are the defaults). For example, for a
non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
#Option "XkbVariant" ""
#Option "XkbOptions" ""
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/psaux"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "Protocol" "IMPS/2"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 30-55
VertRefresh 50-120
Option "dpms"
EndSection
Section "Device"
# no known options
Identifier "NVIDIA GeForce 2 MX (generic)"
Driver "nv"
VendorName "NVIDIA GeForce 2 MX (generic)"
BoardName "NVIDIA GeForce 2 MX (generic)"
#BusID
EndSection
Section "Screen"
Identifier "Screen0"
Device "NVIDIA GeForce 2 MX (generic)"
Monitor "Monitor0"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubsection
EndSection
Section "DRI"
Mode 0666
EndSection
cmdline:
auto BOOT_IMAGE=linux ro BOOT_FILE=/boot/vmlinuz-2.4.18-14
root=LABEL=/
dma:
4: cascade
intrrupts:
CPU0
0: 337647 XT-PIC timer
1: 2694 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 0 XT-PIC usb-ohci, usb-ohci
8: 1 XT-PIC rtc
12: 20 XT-PIC PS/2 Mouse
14: 27338 XT-PIC ide0
NMI: 0
ERR: 2
partitions:
major minor #blocks name rio rmerge rsect ruse wio wmerge
wsect wuse running use aveq
3 0 39121488 hda 2567 4181 52107 22201 1417 1941 26952
45880 -2 329576 7788488
3 1 5245191 hda1 9 43 104 109 0 0 0 0 0 109 109
3 2 1 hda2 0 0 0 0 0 0 0 0 0 0 0
3 5 10490413 hda5 9 43 104 95 0 0 0 0 0 95 95
3 6 11695288 hda6 50 43 145 214 7 1 8 95 0 230 310
3 7 8104761 hda7 9 43 104 132 0 0 0 0 0 132 132
3 8 3277228 hda8 2475 3966 51498 21527 1410 1940 26944
45785 0 22394 67314
3 9 305203 hda9 9 25 104 56 0 0 0 0 0 56 56
My e-mail addresses are: linux_guyus@yahoo.com and
linux_guyus@rediff.com
My postel address: 80, Ahilya Nagar Ext. Annapurna Road, Indore,
M.P.,
India. PIN 452009
please answer me soon.
Thanking you.
Saurabh Khanna.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Jan 31 2003 - 22:00:26 EST