sean darcy wrote:
> ide-scsi refuses to boot with A NULL pointer oops (is there a patch
> yet?). But I figured it didn't matter because I could use cdrecord
> without the scsi layer. So I rebuilt 2.5.54 w/o scsi. Here's the dmesg:
>
> .............
> VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
> ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
> hda: Maxtor 6Y120P0, ATA DISK drive
> hdb: MAXTOR 6L060J3, ATA DISK drive
> hda: DMA disabled
> hdb: DMA disabled
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: SONY CD-RW CRX195E1, ATAPI CD/DVD-ROM drive
> hdc: DMA disabled
> ide1 at 0x170-0x177,0x376 on irq 15
> spurious 8259A interrupt: IRQ7.
> hda: host protected area => 1
> hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=238216/16/63,
> UDMA(133)
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
> hdb: host protected area => 1
> hdb: 117266688 sectors (60041 MB) w/1820KiB Cache, CHS=116336/16/63,
> UDMA(133)
> hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 hdb7 hdb8 >
> ...........
>
> I got cdrecord 2.0:
>
> [root@amd1900 root]# cdrecord -scanbus -dev=ATAPI
> Cdrecord 2.0 (i686-pc-linux-gnu) Copyright (C) 1995-2002 J?rg Schilling
> scsidev: 'ATAPI'
> devname: 'ATAPI'
> scsibus: -2 target: -2 lun: -2
> Warning: Using ATA Packet interface.
> Warning: The related libscg interface code is in pre alpha.
> Warning: There may be fatal problems.
> cdrecord: No such device or address. Cannot open SCSI driver.
> cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you
> are root.
> cdrecord: For possible transport specifiers try 'cdrecord dev=help'.
Did you try cdrecord dev=help like it says? The output of that will
tell you that -scanbus isn't supported with ATAPI devices. I got it
to work blind using 'cdrecord speed=8 dev=ATAPI:0,1,0 -v my.iso' for
a CD-RW at hdb. So, I'm assuming the first 0 is the IDE channel,
the 1 is for a slave (so 0 for master?), and the third I'll just leave
as zero. Of course, don't use the ide-scsi module. Use the ide-cd
module instead.
Hope this helps,
Andy Johnson
>
> FWIW, I also tried just cdrecord -scanbus
>
> What am I missing? I thought we didn't need the scsi layer anymore.
>
> Here are snips from .config:
>
> CONFIG_IDE=y
>
> #
> # IDE, ATA and ATAPI Block devices
> #
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
>
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_IDEDISK_MULTI_MODE=y
>
> CONFIG_BLK_DEV_IDECD=y
>
> # IDE chipset support/bugfixes
> #
>
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_BLK_DEV_GENERIC=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
>
> CONFIG_IDEDMA_PCI_AUTO=y
>
> CONFIG_BLK_DEV_IDEDMA=y
>
> CONFIG_BLK_DEV_ADMA=y
>
> CONFIG_BLK_DEV_VIA82CXXX=y
> CONFIG_IDEDMA_AUTO=y
>
> CONFIG_BLK_DEV_IDE_MODES=y
>
> #
> # SCSI device support
> #
> # CONFIG_SCSI is not set
>
>
>
>
>
>
>
>
>
>
>
> _________________________________________________________________
> Protect your PC - get McAfee.com VirusScan Online
> http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Tue Jan 07 2003 - 22:00:27 EST