klogd 1.4-0, log source = /proc/kmsg started.
Inspecting /boot/System.map-2.4.19-pre4-ac3
Loaded 16316 symbols from /boot/System.map-2.4.19-pre4-ac3.
Symbols match kernel version 2.4.19.
No module symbols loaded.
Linux version 2.4.19-pre4-ac3 (manfred@clmsdev.localdomain) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #21 SMP Fri Mar 29 21:32:52 CET 2002
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000003000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 12288
zone(0): 4096 pages.
zone(1): 8192 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=301 BOOT_FILE=/boot/vmlinuz
No local APIC present or hardware disabled
Initializing CPU#0
Console: colour VGA+ 80x25
Calibrating delay loop... 119.60 BogoMIPS
Memory: 45256k/49152k available (1262k kernel code, 3512k reserved, 839k data, 232k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
kdb version 2.1 by Scott Lurndal, Keith Owens. Copyright SGI, All Rights Reserved
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Enabling CPUID on Cyrix processor.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Cyrix ARR
CPU0: Cyrix 6x86L 2x Core/Bus Clock stepping 02
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
PCI: PCI BIOS revision 2.10 entry at 0xfb610, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 80 slots per queue, batch=20
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 2
VP_IDE: not 100%% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586 (rev 02) IDE MWDMA16 controller on pci00:07.1
    ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:pio, hdd:pio
PDC20269: IDE controller on PCI bus 00 dev 50
PDC20269: chipset revision 2
PDC20269: not 100%% native mode: will probe irqs later
    ide2: BM-DMA at 0x6700-0x6707, BIOS settings: hde:pio, hdf:pio
reset_proc is 0h.
    ide3: BM-DMA at 0x6708-0x670f, BIOS settings: hdg:pio, hdh:pio
reset_proc is 0h.
hda: IBM-DCAA-34330, ATA DISK drive
hde: Maxtor 4G160J8, ATA DISK drive
hdg: Maxtor 4G160J8, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0x6300-0x6307,0x6402 on irq 12
ide3 at 0x6500-0x6507,0x6602 on irq 12
hda: 8467200 sectors (4335 MB) w/96KiB Cache, CHS=527/255/63, DMA
hde: 320173056 sectors (163929 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(33)
hdg: 320173056 sectors (163929 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3
 hde: hde1
 hdg: hdg1
loop: loaded (max 8 devices)
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
  http://www.scyld.com/network/ne2k-pci.html
eth0: RealTek RTL-8029 found at 0x6200, IRQ 10, 00:00:1C:30:58:85.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
ide-floppy driver 0.99.newide
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 232k freed
Adding Swap: 313256k swap-space (priority -1)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736, high=2, low=9587304, sector=43141736
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736, high=2, low=9587304, sector=43141736
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736, high=2, low=9587304, sector=43141736
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736, high=2, low=9587304, sector=43141736
hde: DMA disabled
ide2: reset: success

SYSTEM hang!!!
I don't have the remaining lines, they were something like

ide2: MULTI-READ assume all data transfered is bad status=??
hde: task_mulin_intr: ...
hde: task_mulin_intr: ...
/// And now try_to_flush_leftover_data()->ata_input_data()->'rep;insw;'->hang.