On Wed, Dec 19, 2001 at 12:18:13PM -0400, Brendan Pike wrote:
> On Wednesday 19 December 2001 12:01 pm, Jan Niehusmann wrote:
> > On Wed, Dec 19, 2001 at 11:44:47AM -0400, Brendan Pike wrote:
> > > I dont really know, I dont think its possible to get higher then that
> > > from a 5400 RPM disk. Heres mine,
> >
> > /dev/hda:
> > Timing buffered disk reads: 64 MB in 2.32 seconds = 27.59 MB/sec
> >
> > bash-2.05a# cat /proc/ide/hda/model
> > Maxtor 98196H8
> >
> > This is a 5400rpm drive, too.
> >
> > Jan
> >
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/
>
> wowie, that is quite slow then. well udma33 mode is probebly why. if getting
> an ata100 offboard card (since i have an ata100 drive) would make such a big
> differance, im all for it. would there be any others reasons for such
> slowness? is udma33 capible of more then 9MB/sec ??
Yes. Reaching up to 16 MB/sec with udma33 is quite possible.
> [root@spikes spike]# cat /proc/ide/via
> ----------VIA BusMastering IDE Configuration----------------
> Driver Version: 3.29
> South Bridge: VIA vt82c586b
> Revision: ISA 0x47 IDE 0x6
> Highest DMA rate: UDMA33
> BM-DMA base: 0xe000
> PCI clock: 33MHz
> Master Read Cycle IRDY: 1ws
> Master Write Cycle IRDY: 1ws
> BM IDE Status Register Read Retry: yes
> Max DRDY Pulse Width: No limit
> -----------------------Primary IDE-------Secondary IDE------
> Read DMA FIFO flush: yes yes
> End Sector FIFO flush: no no
> Prefetch Buffer: yes yes
> Post Write Buffer: yes no
> Enabled: yes yes
> Simplex only: no no
> Cable Type: 40w 40w
> -------------------drive0----drive1----drive2----drive3-----
> Transfer Mode: UDMA PIO PIO PIO
> Address Setup: 30ns 120ns 30ns 120ns
> Cmd Active: 90ns 90ns 90ns 90ns
> Cmd Recovery: 30ns 30ns 30ns 30ns
> Data Active: 90ns 330ns 90ns 330ns
> Data Recovery: 30ns 270ns 30ns 270ns
> Cycle Time: 90ns 600ns 120ns 600ns
> Transfer Rate: 22.0MB/s 3.3MB/s 16.5MB/s 3.3MB/s
>
> dont know if that info would help much but there it is. also uses the via
> kernel driver.
But for some reason your drive is running at udma22 (udma1).
-- Vojtech Pavlik SuSE Labs - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Dec 23 2001 - 21:00:19 EST