Has anyone managed to get this motherboard's (tyan tsunami AT) on board
usb to work? I'm currently using an add on pci card to use the usb devices
I have but would _love_ to free that PCI slot up.
Specifics:
Tsunami MB (AT Form factor)
Single processor:
model name : Pentium II (Deschutes)
stepping : 2
cpu MHz : 334.095
cache size : 512 KB
Bios Version 1.16
USB Controller:
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ef80 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 ef 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 04 00 00
Symptoms:
The kernel detects the hub just fine:
usb-uhci.c: $Revision: 1.259 $ time 11:21:32 May 26 2001
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xef80, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
However pluging _anything_ into that hub just don't work, Lots of error
messages about EMI, usb-uhci.c: interrupt, status 3 frame# <blah> Device
disconnects etc etc.
Needless to say said device never gets initalized, though it is detected
as being inserted. So just to be sure I went and got another pair of usb
ports to connect to the header. No joy.
I tried with an external (powered) hub and things atleast got initialized
but was still unable to use the devices (went into that spew about
usb-uhci: interrup, status 3, frame# <blah> over and over again)
Pokeing around I see that the mother board's bios will _always_ assign the
usb controller to IRQ 9, what makes me wonder a bit is this next bit from
lspci:
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00: 86 80 13 71 01 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Thats also routed to IRQ 9 (could this be the problem?)
However _this_ USB controller works just fine:
00:13.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 04) (prog-if
00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 4: I/O ports at ef40 [size=32]
00: 06 11 38 30 17 01 00 42 04 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 ef 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
So its also routed to IRQ 9.
I've tried kernels 2.4.0 -> 2.4.5 all with pretty much the same result
(except 2.4.4 which oops on boot in the usb controller ;) )
I've rummaged around on the linux-usb lists and didn't see anything there.
So is this a known problem with this motherboard/bios version?
Thanks for any tips,
Greg
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Thu May 31 2001 - 21:00:36 EST