Fwd: Re: timeout waiting for DMA

From: Jasmeet Sidhu (jsidhu@arraycomm.com)
Date: Mon Feb 26 2001 - 15:47:56 EST


>Date: Mon, 26 Feb 2001 12:47:30 -0800
>To: Jason Rappleye <rappleye@cse.Buffalo.EDU>
>From: Jasmeet Sidhu <jsidhu@arraycomm.com>
>Subject: Re: timeout waiting for DMA
>
>I had the same exact problem last night using the IBM drives and the ULTRA
>ata/100 controller from Promise. Could this be due to an irq conflict?
>
>kernel: hda: timeout waiting for DMA
>kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
>kernel: hdi: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
>
>and after a few messages my system freazes and can only be brought up by a
>hard reset. Could this be due to faulty cables as well? or is there
>something else that is messing up? I was suspecting an IRQ problem, maybe
>USB is using the same irq (nothing on the USB ports though)... but I am
>not certain. Anybody else out there with similar problems? Any Solutions?
>
>This was suing Kernel 2.4.2 with ac3 patch. Is there a need to apply
>Andre Hedrick's ide patches from kernel 2.4.1?
>
>Jasmeet
>
>
>At 03:41 PM 2/26/2001 -0500, you wrote:
>
>>Hi,
>>
>>I'm running kernel 2.4.2 on an SGI 1100 (dual PIIIs) with a Serverworks
>>III LE based motherboard. The disk is a Seagate ST330630A. The disk has
>>DMA enabled at boot time :
>>
>>hda: ST330630A, ATA DISK drive
>>hda: 59777640 sectors (30606 MB) w/2048KiB Cache, CHS=3720/255/63, UDMA(33)
>>
>>(also verified using hdparm)
>>
>>but after a while (eg partway through running bonnie with a 1GB file) I
>>get the following errors:
>>
>>Feb 24 22:51:02 nash2 kernel: hda: timeout waiting for DMA
>>Feb 24 22:51:02 nash2 kernel: ide_dmaproc: chipset supported ide_dma_timeout
>>func only: 14
>>Feb 24 22:51:02 nash2 kernel: hda: irq timeout: status=0x58 { DriveReady
>>SeekComplete DataRequest }
>><repeats a few times>
>>Feb 24 22:51:32 nash2 kernel: hda: DMA disabled
>>
>>I can reenable DMA without any problems, but after some additional disk
>>activity (eg running bonnie again), the error occurs again.
>>
>>Additional information on my hardware is given below. Any suggestions on
>>how this can be resolved?
>>
>>Thanks,
>>
>>Jason
>>
>>hdparm -i /dev/hda
>>
>>/dev/hda:
>>
>> Model=ST330630A, FwRev=3.21, SerialNo=3CK0JDFE
>> Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
>> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
>> BuffType=0(?), BuffSize=2048kB, MaxMultSect=16, MultSect=off
>> DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
>> CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=59777640
>> tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
>> IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
>> UDMA modes: mode0 mode1 *mode2 mode3 mode4
>>
>>Relevant portion of /proc/pci:
>>
>> Bus 0, device 15, function 1:
>> IDE interface: PCI device 1166:0211 (ServerWorks) (rev 0).
>> Master Capable. Latency=64.
>> I/O at 0x3080 [0x308f].
>>
>>Relevant portion of lspci -v:
>>
>>00:0f.1 IDE interface: Relience Computer: Unknown device 0211 (prog-if 8a
>>[Master SecP PriP])
>> Flags: bus master, medium devsel, latency 64
>> I/O ports at 3080 [size=16]
>>
>>
>>--
>>Jason Rappleye
>>rappleye@buffalo.edu
>>http://www.ccr.buffalo.edu/jason.htm
>>
>>
>>-
>>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>>the body of a message to majordomo@vger.kernel.org
>>More majordomo info at http://vger.kernel.org/majordomo-info.html
>>Please read the FAQ at http://www.tux.org/lkml/
>
>
>- - -
>Jasmeet Sidhu
>Unix Systems Administrator
>ArrayComm, Inc.
>jsidhu@arraycomm.com
>www.arraycomm.com

- - -
Jasmeet Sidhu
Unix Systems Administrator
ArrayComm, Inc.
jsidhu@arraycomm.com
www.arraycomm.com

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/



This archive was generated by hypermail 2b29 : Wed Feb 28 2001 - 21:00:12 EST